Normal values of overflow rate for plain sedimentation tank, is
(A) 250 to 500 litres/hr/m2
(B) 500 to 750 litres/hr/m2
(C) 750 to 1000 litres/hr/m2
(D) 1000 to 1250 litres/hr/m
(B) 500 to 750 litres/hr/m
Description : Normal values of overflow rate for plain sedimentation tank using coagulants, is (A) 750 to 1000 litres/hr/m2 (B) 1000 to 1250 litres/hr/m2 (C) 1250 to 1500 litres/hr/m2 (D) 1500 litres/hr/m
Last Answer : (B) 1000 to 1250 litres/hr/m2
Description : Normal values of overflow rate for sedimentation tanks using coagulants in litres/hr/m2 , generally range between (A) 250 to 500 (B) 500 to 750 (C) 750 to 1000 (D) 1000 to 1250
Last Answer : (D) 1000 to 1250
Description : Normal values of overflow rate for plain sedimentation tanks in litres/hr/m2 , generally range between (A) 100 to 250 (B) 250 to 500 (C) 500 to 750 (D) 750 to 1000
Last Answer : (C) 500 to 750
Description : Concrete pavement is provided if daily traffic per lane exceeds (A) 500 tonnes (B) 750 tonnes (C) 1000 tonnes (D) 1250 tonnes
Last Answer : Answer: Option C
Description : A three hinged arch is loaded with an isolated load 1000 kg at a horizontal distance of 2.5 m from the crown, 1 m above the level of hinges at the supports 10 metres apart. The horizontal thrust is (A) 1250 kg (B) 125 kg (C) 750 kg (D) 2500 kg
Last Answer : (A) 1250 kg
Description : How many mL of a 1:500 w/v stock solution should be used to make 5 liters of 1:2000 w/v solution? (A) 750 mL (B) 1000 mL (c) 1250 mL (D) 1500 mL
Last Answer : (c) 1250 mL
Description : A sells an article to B at 15% profit. B sells it to C at 10% loss. If C pays Rs 517.50 for it then A purchased it at: 1. Rs 500 2. Rs 750 3. Rs 1000 4. Rs 1250
Last Answer : 1. Rs 500
Description : The ratio of design discharge to the surface area of a sedimentation tank is called A. Surface loading B. Overflow rate C. Overflow velocity D. All of these
Last Answer : ANS: D
Description : The normal value of over flow rates for plain primary sedimentation tanks, ranges between A. 25,000 to 35,000 litres/sqm/day B. 40,000 to 50,000 litres/sqm/day C. 50,000 to 60,000 litres/sqm/day D. 80,000 to 100,000 litres/sqm/day
Last Answer : ANS: B
Description : One cubic metre of water weighs (A) 100 litres (B) 250 litres (C) 500 litres (D) 1000 litres
Last Answer : Answer: Option D
Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750
Last Answer : (A) 500
Description : The normal values of over flow rates for secondary sedimentation tanks, ranges between A. 25,000 to 35,000 litres/sqm/day B. 40,000 to 50,000 litres/sqm/day C. 50,000 to 60,000 litres/sqm/day D. 80,000 to 10,000 litres/sqm/day
Last Answer : ANS: A
Description : The normal values of over flow rates for sedimentation tanks using coagulant, ranges between A. 25,000 to 35,000 litres/sqm/day B. 40,000 to 50,000 litres/sqm/day C. 50,000 to 60,000 litres/sqm/day D. 80,000 to 100,000 litres/sqm/day
Last Answer : ANS: C
Description : Water filtration rate in a slow sand filter ranges from __________ litres/m2 /hr. (A) 10 to 20 (B) 100 to 200 (C) 1500 to 2500 (D) 4000 to 5000
Last Answer : (B) 100 to 200
Description : The amount of air breathed in and out in a single quiet respiration is about (a) 250 ml (b) 500 ml (c) 750 ml (d) 1000 ml
Last Answer : Ans:(d)
Description : The gradient of a platform is generally (a) 1 in 1000 (b) 1 in 750 (c) 1 in 500* (d) 1 in 250
Last Answer : (c) 1 in 500*
Description : The cutter bar of a tractor operated on owner makes strokes/min (a) 400 – 500 (b) 500 – 750 (c) 800 – 1200 (d) 1250 – 1500
Last Answer : (c) 800 – 1200
Description : For design purposes, the normal rate of infiltration of ground water into the sewer, is A. 500 litres/km/cm B. 1000 litres/km/cm C. 1500 litres/km/cm D. 2000 litres/km/cm
Description : Detention time for plain sedimentation tank usually ranges from (A) 2 to 4 hours (B) 4 to 8 hours (C) 6 to 10 hours (D) 8 to 12 hours
Last Answer : (B) 4 to 8 hours
Description : Velocity of flow of water in plain sedimentation water tank, is normally kept (A) 3 cm/minute (B) 10 cm/minute (C) 20 cm/minute (D) 30 cm/minute
Last Answer : (D) 30 cm/minute
Description : If the velocity of moving vehicles on a road is 24 km/per hour, stopping distance is 19 metres and average length of vehicles is 6 metres, the basic capacity of lane, is (A) 500 vehicles per hour (B) 700 vehicles per hour (C) 1000 vehicles per hour (D) 1250 vehicles per hour
Description : 52 A transformer has 1000 primary turns, connected to 250V ac supply. To get 400V secondary voltage the no of secondary turns should be A. 1600 B. 250 C. 400 D. 1250
Last Answer : A. 1600
Description : A masonry dam (density = 20,000 N/m3 ) 6 m high, one metre wide at the top and 4 m wide at the base, has vertical water face. The minimum stress at the base of the dam when the reservoir is full, will be (A) 75 N/m2 (B) 750 N/m2 (C) 7500 N/m2 (D) 75000 N/m
Last Answer : (C) 7500 N/m
Description : The ratio of discharge and plan area of a continuous flow type settling tank, is known (A) Surface loading (B) Overflow (C) Overflow rate (D) All the above
Last Answer : (D) All the above
Description : A well penetrates to 30 m below the static water table. After 24 hours of pumping at 31.40 litres/minute, the water level in a test well at a distance of 80 m is lowered by 0.5 m and in a well 20 m away water is ... 1.185 m2 /minute (B) 1.285 m2 /minute (C) 1.385 m2 /minute (D) 1.485 m2 /minute
Description : In plain sedimentation tanks under normal conditions, impurities are removed upto (A) 60 % (B) 70 % (C) 80 % (D) 90 %
Last Answer : (B) 70 %
Description : The Vertical Separation Minimum (VSM) for flights in accordance with IFR within controlled airspace below FL290 is: a. 500 feet (150m) b. 2500 feet (750 m) c. 1000 feet (300m) d. 2000 feet (600m)
Last Answer : c. 1000 feet (300m)
Description : The respective storm totals at three surrounding stations A, B and C are 110, 90 and 70 mm. If the normal annual precipitation amounts at stations X, A, B and C are respectively 1000, 1100, 1200 and 1250 mm, the estimated storm precipitation at X is (A) 75 mm (B) 77 mm (C) 79 mm
Last Answer : Answer: Option B
Description : To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length of the ... the water horse power of the pump is (A) 400 (B) 450 (C) 500 (D) 600
Last Answer : (D) 600
Description : Pick up the correct statement from the following: (A) Detention period for plain sedimentation tanks ranges between 4 to 8 hours (B) Detention period for sedimentation tanks, using coagulants usually ... in sedimentation tanks, is generally limited to 0.3 m/minute (D) All the above
Description : How many voice signals (4 kHz max.) would fit into a 5 MHz spectrum? A. 1250 B. 500 C. 1000 D. 1500
Last Answer : A. 1250
Description : Hydrogen content in petroleum products varies from 12 to 15% (by weight). As a result the difference between gross and net heating value of petroleum fuels varies in the range of __________ kcal/kg. (A) 600-750 (B) 250-350 (C) 1000-1500 (D) 2000-2500
Last Answer : (A) 600-750
Description : If the purchases made during the year were Rs. 60,000, the balance of stock in trade at the beginning and at the end of the year were Rs. 12,000 and Rs. 9,000 respectively and the gross profit on sales was 1/5th, when which ... year ? (A) Rs. 15,750 (B) Rs. 14,000 (C) Rs. 12,500 (D) Rs. 17,250
Last Answer : Answer: Rs. 12,500
Description : Fusion zone in the electric furnace used for reduction of phosphate rock to elemental phosphorous is maintained at __________ °C. (A) 250-300 (B) 500-750 (C) 950-1050 (D) 1400-1450
Last Answer : (D) 1400-1450
Description : Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F
Last Answer : (C) 50 -100 BTU/hr. ft. 2°F
Description : Metallic recuperators are not used for waste heat recovery, if the hot flue gas temperature is above __________ °C, because corrosion prevails at higher temperatures. (A) 350 (B) 750 (C) 1050 (D) 1250
Last Answer : (B) 750
Description : The floor of a rectangular hall has a perimeter 250 m. If the cost of painting the four walls at the rate of Rs.10 per m2 is Rs.15000, find the height of the hall. -Maths 9th
Last Answer : Let length, breadth, and height of the rectangular hall be l, b, and h respectively. Area of four walls = 2lh+2bh = 2(l+b)h Perimeter of the floor of hall = 2(l+b) = 250 m Area of four walls = 2( ... of paining the walls is Rs. 15000. 15000 = 2500h Or h = 6 Therefore, the height of the hall is 6 m.
Description : Tap A can fill a tank of 1000 litres capacity in 14 hours. It can fill a tank of ……… litres in 7 hours.
Last Answer : Tap A can fill a tank of 1000 litres capacity in 14 hours. It can fill a tank of ……… litres in 7 hours.
Description : One litre of water occupies a volume of (A) 100 cm3 (B) 250 cm3 (C) 500 cm3 (D) 1000 cm3
Last Answer : Answer: Option A
Description : In cement pressure grouting holes should be drilled at spacing in both direction at a) 150 – 500 mm b) 450 mm c) 500 – 750 mm* d) 1000 mm
Last Answer : c) 500 – 750 mm*
Description : The detention period for plain sedimentation water tanks, is usually (A) 4 to 8 hours (B) 8 to 16 hours (C) 16 to 24 hours (D) 24 to 36 hours
Last Answer : (D) 24 to 36 hours
Description : A goodstrain of 700 m runs at a speed of 165 km/hr. A person traveling in it observes that the mail train moving in opposite direction takes 30 seconds to cross him. Find the speed of the mail train, if it is 750 m long. A) 8.4 m/s B) 5.3 m/s C) 2.5 m/s D) 6.8 m/s
Last Answer : ANSWER:C Explanation: Speed of goods train = 165km/hr length of mail train (P) = 750m length of goods train (Q) = 700m Alternately, we can directly use the formula: Time = ( p+q) / (v1+v2) sec ( ... 45.833+v2 = 48.333 V2 = 2.5 m/s Therefore the speed of the mail train is 2.5 m/s
Description : Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per m2 of steel strip. (A) 5-10 (B) 1000-1500 (C) 120-500 (D) 1500-3000
Last Answer : Option C
Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200
Last Answer : (B) 100
Description : An excavator costs Rs. 20,00,000 and has an estimated life of 8 years. It has no salvage value at the end of 8 years. The book value of the excavator at the end of 3 years using general double declining balance method is (A) Rs. 8,43,750 (B) Rs. 8,75,000 (C) Rs. 10,50,000 (D) Rs. 11,56,250
Last Answer : (A) Rs. 8,43,750
Description : Side face reinforcement is provided when the depth of beam exceeds [ A ] 250 mm [ B ] 450 mm [ C ] 550 mm [ D ] 750 mm
Last Answer : [ D ] 750 mm
Description : Water is following at the rate of 5 km/hr through a pipe of diameter 14 cm into a rectangular tank which is 50 m long -Maths 9th
Last Answer : Convert all to metres: 5 km = 5000 m 14 cm = 0.14 m 7 cm = 0.07 m Find the radius: Radius = Diameter 2 Radius = 0.14 2 = 0.07 m Find the amount of water that flowed out in an hour: Volume ... hours needed: Number of hours = 154 77 = 2 hours It takes 2 hours to fill up the tank to rise by 7 cm
Description : The requirement of water per capita per day, is (A) 90 litres (B) 150 litres (C) 250 litres (D) 400 litres
Last Answer : (A) 90 litres
Description : The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ
Last Answer : (A) 3.6 AVS.ρ