A Bingham fluid of viscosity μ = 10 Pa.s and yield stress, τ0 = 10 KPa, is shared between flat parallel plates separated by a distance of 10 -3 m. The top plate is moving with a velocity of 1 m/s. The shear stress on the plate is (A) 10 KPa (B) 20 KPa (C) 30 KPa (D) 40 KPa

A Bingham fluid of viscosity μ = 10 Pa.s and yield stress, τ0 = 10 KPa, is
shared between flat parallel plates separated by a distance of 10
-3 m. The
top plate is moving with a velocity of 1 m/s. The shear stress on the plate is
(A) 10 KPa
(B) 20 KPa
(C) 30 KPa
(D) 40 KPa
by

1 Answer

Answer :

(B) 20 KPa
by

Related questions

In case of Couette flow, the fluid flow is between two large flat parallel plates with (A) Top plate moving and the bottom plate fixed (B) Bottom plate moving and the top plate fixed (C) Both the plates fixed (D) Both the plates moving

Description : In case of Couette flow, the fluid flow is between two large flat parallel plates with (A) Top plate moving and the bottom plate fixed (B) Bottom plate moving and the top plate fixed (C) Both the plates fixed (D) Both the plates moving

Last Answer : (A) Top plate moving and the bottom plate fixed

As per Newton's law of viscosity, the shear stress for a given rate of angular deformation of fluid is proportional to (where, μ = fluid viscosity) (A) 1/μ (B) μ (C) μ 2 (D) 1/μ

Description : As per Newton's law of viscosity, the shear stress for a given rate of angular deformation of fluid is proportional to (where, μ = fluid viscosity) (A) 1/μ (B) μ (C) μ 2 (D) 1/μ

Last Answer : (B) μ

The velocity profile for a Bingham plastic fluid flowing (under laminar conditions) in a pipe is (A) Parabolic (B) Flat (C) Flat near the wall and parabolic in the middle (D) Parabolic near the wall and flat in the middle

Description : The velocity profile for a Bingham plastic fluid flowing (under laminar conditions) in a pipe is (A) Parabolic (B) Flat (C) Flat near the wall and parabolic in the middle (D) Parabolic near the wall and flat in the middle

Last Answer : (D) Parabolic near the wall and flat in the middle

The pressure drop in a 30 cm diameter horizontal pipe is 60 kPa in distance of 15m. The wall shear stress in kPa is (a) 0.1 (b) 0.2 (c) 0.3 (d) 0.4

Description : The pressure drop in a 30 cm diameter horizontal pipe is 60 kPa in distance of 15m. The wall shear stress in kPa is (a) 0.1 (b) 0.2 (c) 0.3 (d) 0.4

Last Answer : (c) 0.3

The fluid in which the shearing stress within it is proportional to the velocity gradient across the sheared section, is called a __________ fluid. (A) Bingham (B) Newtonian (C) Perfect (D) None of these

Description : The fluid in which the shearing stress within it is proportional to the velocity gradient across the sheared section, is called a __________ fluid. (A) Bingham (B) Newtonian (C) Perfect (D) None of these

Last Answer : (B) Newtonian

For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) (A) μ (B) 1/μ (C) √μ (D) 1/√μ

Description : For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) (A) μ (B) 1/μ (C) √μ (D) 1/√μ

Last Answer : (B) 1/μ

Pick out the wrong statement. (A) Momentum transfer in laminar flow results from velocity gradient (B) A fluid in equilibrium is not free from shear stress (C) The viscosity of a non-Newtonian fluid is a function of temperature only (D) Both (B) and (C)

Description : Pick out the wrong statement. (A) Momentum transfer in laminar flow results from velocity gradient (B) A fluid in equilibrium is not free from shear stress (C) The viscosity of a non-Newtonian fluid is a function of temperature only (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Newton's law of viscosity relates the (A) Shear stress and velocity (B) Velocity gradient and pressure intensity (C) Shear stress and rate of angular deformation in a fluid (D) Pressure gradient and rate of angular deformation

Description : Newton's law of viscosity relates the (A) Shear stress and velocity (B) Velocity gradient and pressure intensity (C) Shear stress and rate of angular deformation in a fluid (D) Pressure gradient and rate of angular deformation

Last Answer : (C) Shear stress and rate of angular deformation in a fluid

Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent) varies linearly as the radial distance (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Description : Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent ... of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Last Answer : (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity

At the point of boundary layer separation in fluid flow, the (A) Shear stress is maximum (B) Velocity gradient is flat (C) Density variation is maximum (D) Shear stress is zero

Description : At the point of boundary layer separation in fluid flow, the (A) Shear stress is maximum (B) Velocity gradient is flat (C) Density variation is maximum (D) Shear stress is zero

Last Answer : Option A

Bulk modulus of a fluid is the ratio of (A) Shear stress to shear strain (B) Increase in volume to the viscosity of fluid (C) Increase in pressure to the volumetric strain (D) Critical velocity to the viscosity of fluid

Description : Bulk modulus of a fluid is the ratio of (A) Shear stress to shear strain (B) Increase in volume to the viscosity of fluid (C) Increase in pressure to the volumetric strain (D) Critical velocity to the viscosity of fluid

Last Answer : Answer: Option C

Consider the following statements in respect of steady laminar flow through a circular pipe: 1. Shear stress is zero on the central axis of the pipe 2. Discharge varies directly with the viscosity of the fluid 3. Velocity is maximum at the centre of the pipe. 4. Hydraulic gradient varies as the square of the mean velocity of flow. Which of these statements are correct? (a) 1, 2 , 3 & 4 (b) 1 & 3 only (c) 2 & 4 only (d)3 & 4 only

Description : Consider the following statements in respect of steady laminar flow through a circular pipe: 1. Shear stress is zero on the central axis of the pipe 2. Discharge varies directly with the viscosity of the fluid 3. Velocity is maximum at the ... 2 , 3 & 4 (b) 1 & 3 only (c) 2 & 4 only (d)3 & 4 only

Last Answer : (b) 1 & 3 only

A gas (density = 1.5 kg/m3 , viscosity = 2 × 10 ‒5 kg/m.s) flowing through a packed bed (particle size = 0.5 cm, porosity = 0.5) at a superficial velocity of 2 m/s causes a pressure drop of 8400 Pa/m. The pressure drop for another gas, with density of 1.5 kg/m3and viscosity of 3 × 10 ‒5kg/m.s flowing at 3 m/s will be (A) 8400 Pa/m (B) 12600 Pa/m (C) 18900 Pa/m (D) 16800 Pa/m

Description : A gas (density = 1.5 kg/m3 , viscosity = 2 10 -5 kg/m.s) flowing through a packed bed (particle size = 0.5 cm, porosity = 0.5) at a superficial velocity of 2 m/s causes a pressure drop of 8400 Pa/m. The ... flowing at 3 m/s will be (A) 8400 Pa/m (B) 12600 Pa/m (C) 18900 Pa/m (D) 16800 Pa/m

Last Answer : (B) 12600 Pa/m

In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are. (A) μ , α and θ all have units of m/s (B) μ , α and θ all have units of m2/s (C) α and θ have units of m2/s, while μ has unit of m/s (D) α and θ have units of m/s, while μ has unit of m2/s

Description : In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are. (A) μ , α and θ all have units of m/ ... μ has unit of m/s (D) α and θ have units of m/s, while μ has unit of m2/s

Last Answer : Option C

In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder (C) Velocity profile varies hyperbolically and the shear stress remains constant over the cross-section (D) Average flow occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Description : In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a ... occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Last Answer : (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder

The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic

Description : The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic

Last Answer : (B) Pseudo-plastic

The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian

Description : The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian

Last Answer : (A) Dilatent

The time required to stop a car moving with a velocity 20 m/sec within a distance of 40 m is equal to a.8 sec b.2 sec c.4 sec d.10 sec e.6 sec

Description : The time required to stop a car moving with a velocity 20 m/sec within a distance of 40 m is equal to a.8 sec b.2 sec c.4 sec d.10 sec e.6 sec

Last Answer : c. 4 sec

Calculate the capacitance of two parallel plates of area 2 units separated by a distance of 0.2m in air(in picofarad) a) 8.84 b) 88.4 c) 884.1 d) 0.884

Description : Calculate the capacitance of two parallel plates of area 2 units separated by a distance of 0.2m in air(in picofarad) a) 8.84 b) 88.4 c) 884.1 d) 0.884

Last Answer : b) 88.4

A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Description : A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Last Answer : (a) S = (μN s /p) (r/c) 2

Electric field strength on a dust particle having charge equal to 8 × 10- 19 when plates are separated by distance of 2 cm and have a potential difference of 5 kV is A. 2.0 × 10-13 NB. 3 NC. 5 ND. 20 N

Description : Electric field strength on a dust particle having charge equal to 8 × 10- 19 when plates are separated by distance of 2 cm and have a potential difference of 5 kV is A. 2.0 × 10-13 N B. 3 N C. 5 N D. 20 N

Last Answer : 2.0 × 10-13 N

Newton's law of viscosity, which states that the shear stress is proportional to the __________ Co-efficient of viscosity is called dynamic or absolute viscosity(where, V = velocity, Vg = velocity gradient). (A) V2 (B) 1/V2 (C) 1/Vg (D) Vg

Description : Newton's law of viscosity, which states that the shear stress is proportional to the __________ Co-efficient of viscosity is called dynamic or absolute viscosity(where, V = velocity, Vg = velocity gradient). (A) V2 (B) 1/V2 (C) 1/Vg (D) Vg

Last Answer : Option D

The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Description : The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Last Answer : Ans: (c) Correct Answer is: 0.45 m

According to Newton's law of viscosity, the shear stress on a layer of a fluid is __________ to the rate of shear strain. (A) Equal to (B) Directly proportional (C) Inversely proportional (D) None of these

Description : According to Newton's law of viscosity, the shear stress on a layer of a fluid is __________ to the rate of shear strain. (A) Equal to (B) Directly proportional (C) Inversely proportional (D) None of these

Last Answer : Answer: Option B

A 30-m vertical column of fluid (density 1878 kg/m3 ) is located where g= 9.65 mps2 . Find the pressure at the base of the column. (Formula: pg= gρhg/k )  a. 543680 N/m2  b. 543.68 kPa (gauge)  c. Both a & b  d. None of the above

Description : A 30-m vertical column of fluid (density 1878 kg/m3 ) is located where g= 9.65 mps2 . Find the pressure at the base of the column. (Formula: pg= gρhg/k )  a. 543680 N/m2  b. 543.68 kPa (gauge)  c. Both a & b  d. None of the above

Last Answer : Both a & b

Newton's law of viscosity is a relationship between (A) Shear stress and the rate of angular distortion (B) Shear stress and viscosity (C) Shear stress, velocity and viscosity (D) Pressure, velocity and viscosity

Description : Newton's law of viscosity is a relationship between (A) Shear stress and the rate of angular distortion (B) Shear stress and viscosity (C) Shear stress, velocity and viscosity (D) Pressure, velocity and viscosity

Last Answer : Answer: Option A

Newton's law of viscosity is a relationship between (A) Pressure, velocity and temperature (B) Shear stress and rate of shear strain (C) Shear stress and velocity (D) Rate of shear strain and temperature

Description : Newton's law of viscosity is a relationship between (A) Pressure, velocity and temperature (B) Shear stress and rate of shear strain (C) Shear stress and velocity (D) Rate of shear strain and temperature

Last Answer : Answer: Option B

Five volts are applied across the plates of a parallel plate capacitor. The distance of separation of the plates is .02 meters. What is the magnitude of the electric field inside the capacitor?

Description : Five volts are applied across the plates of a parallel plate capacitor. The distance of separation of the plates is .02 meters. What is the magnitude of the electric field inside the capacitor?

Last Answer : ANSWER: 250 VOLTS PER METER or 250 NEWTONS PER COULOMB

A fluid is termed as the Newtonian fluid, when the shear stress is __________ the velocity gradient. (A) Independent of (B) Inversely proportional to (C) Directly proportional to (D) None of these

Description : A fluid is termed as the Newtonian fluid, when the shear stress is __________ the velocity gradient. (A) Independent of (B) Inversely proportional to (C) Directly proportional to (D) None of these

Last Answer : (C) Directly proportional to

Filtration rate through a filter cake is proportional to (where, S = filtering surface R = specific cake resistance μ = viscosity of the filtrate) (A) S (B) 1/R (C) 1/μ (D) All (A), (B) & (C)

Description : Filtration rate through a filter cake is proportional to (where, S = filtering surface R = specific cake resistance μ = viscosity of the filtrate) (A) S (B) 1/R (C) 1/μ (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Last Answer : c. 20.120 N/mm2

Two straight wires each 10 cm long are parallel to one another and separated by 2 cm. when the current flowing in them is 30 A and 40 A respectively t

Description : Two straight wires each 10 cm long are parallel to one another and separated by 2 cm. when the current flowing in them is 30 A and 40 A respectively t

Last Answer : Two straight wires each 10 cm long are parallel to one another and separated by 2 cm. when the current flowing in ... 2xx10^(-3)N` D. `10.2x10^(-3)N`

. In case of turbulent flow of fluid through a circular pipe, the (A) Mean flow velocity is about 0.5 times the maximum velocity (B) Velocity profile becomes flatter and flatter with increasing Reynolds number (C) Point of maximum instability exists at a distance of 2r/3 from the pipe wall (r = pipe radius) (D) Skin friction drag, shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

Description : . In case of turbulent flow of fluid through a circular pipe, the (A) Mean flow velocity is about 0.5 times the maximum velocity (B) Velocity profile becomes flatter and flatter with ... , shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

Last Answer : (D) Skin friction drag, shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Description : According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Last Answer : a) X=30 Y=18

According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Description : According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Last Answer : a) X=30 Y=18

According to ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Description : According to ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Last Answer : a) X=30 Y=18

A jet of water of cross-sectional area 20 sq. cm impinges on a plate at an angle of 60? with a velocity of 10 m/sec. Neglecting the friction between the jet and plate (density of water 1000/9.81 kgm-1 sec2 per cubic meter), the force exerted by the jet on the plate would be in the range a.15 - 20 kg b.20 - 25 kg c.5 - 10 kg d.25 - 30 kg e.10 - 15 kg

Description : A jet of water of cross-sectional area 20 sq. cm impinges on a plate at an angle of 60? with a velocity of 10 m/sec. Neglecting the friction between the jet and plate (density of water 1000/9.81 kgm-1 sec2 per cubic meter), the ... a.15 - 20 kg b.20 - 25 kg c.5 - 10 kg d.25 - 30 kg e.10 - 15 kg

Last Answer : a. 15 - 20 kg

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

Rubber latex is an example of a __________ fluid. (A) Pseudo plastic (B) Bingham plastic (C) Dilatent (D) Newtonian

Description : Rubber latex is an example of a __________ fluid. (A) Pseudo plastic (B) Bingham plastic (C) Dilatent (D) Newtonian

Last Answer : (A) Pseudo plastic

Sewage sludge is an example of the __________ fluid. (A) Bingham plastic (B) Newtonian (C) Pseudo plastic (D) Dilatent

Description : Sewage sludge is an example of the __________ fluid. (A) Bingham plastic (B) Newtonian (C) Pseudo plastic (D) Dilatent

Last Answer : (A) Bingham plastic

Sewage sludge is __________ type of non-Newtonian fluid. (A) Dilatant (B) Bingham plastic (C) Pseudo plastic (D) None of these

Description : Sewage sludge is __________ type of non-Newtonian fluid. (A) Dilatant (B) Bingham plastic (C) Pseudo plastic (D) None of these

Last Answer : (B) Bingham plastic

Rubber latex is an example of __________ fluid. (A) Dilatants (B) Newtonian (C) Pseudo plastic (D) Bingham plastic

Description : Rubber latex is an example of __________ fluid. (A) Dilatants (B) Newtonian (C) Pseudo plastic (D) Bingham plastic

Last Answer : (C) Pseudo plastic

Quicksand is an example of a __________ fluid. (A) Bingham plastic (B) Dilatant (C) Newtonian (D) Pseudo plastic

Description : Quicksand is an example of a __________ fluid. (A) Bingham plastic (B) Dilatant (C) Newtonian (D) Pseudo plastic

Last Answer : (B) Dilatant

Paper pulp is an example of __________ fluid.(A) Dilatant (B) Bingham plastic (C) Newtonian (D) Pseudo-plastic

Description : Paper pulp is an example of __________ fluid. (A) Dilatant (B) Bingham plastic (C) Newtonian (D) Pseudo-plastic

Last Answer : (B) Bingham plastic

A liquid mixture contains 30% o-xylene, 60% p-xylene and 10%. m￾xylene (all percentages in w/w). Which of the following statements would be true in respect of this mixture? (A) The mixture exhibits an azeotrope at 101.3 kPa (B) The composition of the mixture, in percent by volume is: o-xylene 30, p￾xylene 60. and m-xylene 10 (C) The composition of the mixture in mole percent is: o-xylene 30, p-xylene 60 and m-xyoene 10 (D) The mixture contain optical isomers

Description : A liquid mixture contains 30% o-xylene, 60% p-xylene and 10%. m￾xylene (all percentages in w/w). Which of the following statements would be true in respect of this mixture? (A) The mixture exhibits ... : o-xylene 30, p-xylene 60 and m-xyoene 10 (D) The mixture contain optical isomers

Last Answer : (A) The mixture exhibits an azeotrope at 101.3 kPa

A lubricant 100 times more viscous than water would have a viscosity (in Pa.s) (A) 0.01 (B) 0.1 (C) 1 (D) 10

Description : A lubricant 100 times more viscous than water would have a viscosity (in Pa.s) (A) 0.01 (B) 0.1 (C) 1 (D) 10

Last Answer : (B) 0.1

Unit for pressure used in weather maps is millibar. 1 millibar is equal to A. 1000 bar B. 100 kPa C. 100 Pa D. 1 atm

Description : Unit for pressure used in weather maps is millibar. 1 millibar is equal to A. 1000 bar B. 100 kPa C. 100 Pa D. 1 atm

Last Answer : 100 Pa

A pressure gage registers 50 psig in a region where the barometer is 14.25 psia. Find absolute pressure in psia, Pa. (Formula; p = patm+ pg)  a. 433 kPa  b. 443 kPa  c. 343 kPa  d. None of the above

Description : A pressure gage registers 50 psig in a region where the barometer is 14.25 psia. Find absolute pressure in psia, Pa. (Formula; p = patm+ pg)  a. 433 kPa  b. 443 kPa  c. 343 kPa  d. None of the above

Last Answer : 443 kPa

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Last Answer : a) M/2πtr2