Draw impedance triangle and voltage triangle for RL series circuit

Draw impedance triangle and voltage triangle for RL series circuit
by

1 Answer

Answer :

image

impedance triangle and voltage triangle for RL series circuit

by

Related questions

Draw a circuit diagram of R.C. series circuit. Draw impedance triangle and power triangle for same circuit.

Description : Draw a circuit diagram of R.C. series circuit. Draw impedance triangle and power triangle for same circuit. 

Last Answer : Draw a circuit diagram of R.C. series circuit. Draw impedance triangle and power triangle for same circuit. 

What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively?

Description : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

Last Answer : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

How are the voltage drop across R and XL related in series RL circuit?

Description : How are the voltage drop across R and XL related in series RL circuit?

Last Answer : Voltage drop across a circuit is IZ, where I is current and Z isimpedance. In other words IZ = IR + jIX, where R is resistance andX is inductance

A unit step voltage is applied at t = 0 to a series RL circuit with zero initial conditions

Description : A unit step voltage is applied at t = 0 to a series RL circuit with zero initial conditions  A) It is possible for the current to be oscillatory B) The voltage across the resistor at t ... The energy stored in the inductor in the steady state is zero D) Theresistor current eventually falls to zero 

Last Answer : A

Two resistances Rl and Ri are connected in series across the voltage...

Description : Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across?

Last Answer : Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across Rl.

Turn-on time of an SCR in series with RL circuit can be reduced by

Description : Turn-on time of an SCR in series with RL circuit can be reduced by   (a) Increasing circuit resistance R (b) Decreasing R (c) Increasing circuit inductance L (d) Decreasing L 

Last Answer : Turn-on time of an SCR in series with RL circuit can be reduced by Decreasing L 

The component labeled 'CR1' in the circuit shown in the illustration __________________. EL-0085 A. varies its anode/cathode polarity depending on 'RL' current B. rectifies the varying voltage from the collector of 'Q1' C. acts as a low capacitive reactance to smooth ripple D. establishes a constant reference voltage for the base of 'Q1'

Description : The component labeled 'CR1' in the circuit shown in the illustration __________________. EL-0085 A. varies its anode/cathode polarity depending on 'RL' current B. rectifies the varying voltage from the ... reactance to smooth ripple D. establishes a constant reference voltage for the base of 'Q1'

Last Answer : Answer: D

An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to

Description :  An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when A) ZL = R B) ZL = jXS C) ZL = R-jXS D) ZL = R+jXS 

Last Answer :  An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when ZL = R-jXS

In an R-C-L series circuit, during resonance, the impedance will be _____.

Last Answer : In an R-C-L series circuit, during resonance, the impedance will be minimum.

In a series resonant circuit, the impedance of the circuit is?

Description : In a series resonant circuit, the impedance of the circuit is?

Last Answer : In a series resonant circuit, the impedance of the circuit is minimum.

A negative feedback loop returning a voltage to the input raised the input impedance and making the circuit a better

Description : A negative feedback loop returning a voltage to the input raised the input impedance and making the circuit a better

Last Answer : A negative feedback loop returning a voltage to the input raised the input impedance and making the circuit a better voltage sensor

Source free RL circuit 8

Description : Source free RL circuit 8

Last Answer : Source free RL circuit 8

Source free RL circuit 7

Description : Source free RL circuit 7

Last Answer : Source free RL circuit 7

Source free RL circuit 6

Description : Source free RL circuit 6

Last Answer : Source free RL circuit 6

Source free RL circuit 1

Description : Source free RL circuit 1

Last Answer : Source free RL circuit 1

Source free RL circuit 2

Description : Source free RL circuit 2

Last Answer : Source free RL circuit 2

Source free RL circuit 3

Description : Source free RL circuit 3

Last Answer : Source free RL circuit 3

Source free RL circuit 4

Last Answer : Source free RL circuit 4

Source free RL circuit 5

Last Answer : Source free RL circuit 5

Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Description : Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Last Answer : Single phase fully control bridge converter with RL load: 1. During positive half cycle of input voltage, T1 and T2 are forward biased and during negative half cycle, T3 and T4 are forward biased. Therefore, T1-T2 ... cycle till the firing of next pair of SCRs as shown in the waveform.

Draw a neat diagram of 1Ф half wave controlled converter with RL load. Give its operation.

Description : Draw a neat diagram of 1Ф half wave controlled converter with RL load. Give its operation.

Last Answer : Single phase fully controlled half wave converter:  The circuit diagram of single-phase half-wave controlled rectifier with RL load and without freewheeling diode is shown in Fig. (a). The SCR T is ... , when again pulse is applied, the SCR is turned on & the above cycle is repeated. 

For R-C series circuit draw (i) Circuit diagram (ii) Vector diagram (iii) Waveform of voltage and current

Description : For R-C series circuit draw (i) Circuit diagram (ii) Vector diagram (iii) Waveform of voltage and current

Last Answer : i) Circuit diagram ii)Vector diagram iii)Waveform of voltage and current

The formula for computing impedance in a series circuit containing resistance, capacitance, and inductance is _____________. [ NOTE: the symbol * stands for 'multiplied by' ] A. Z = RT + XL + XC B. Z = R + XL - XC C. Z * Z = R * R + (XL - XC) * (XL - XC) D. Z = R * R + (XL * XC) - (XL * XC)

Description : The formula for computing impedance in a series circuit containing resistance, capacitance, and inductance is _____________. [ NOTE: the symbol * stands for 'multiplied by' ] A. Z = RT + XL + XC B. Z = R + XL - XC C. Z * Z = R * R + (XL - XC) * (XL - XC) D. Z = R * R + (XL * XC) - (XL * XC)

Last Answer : Answer: C

The combined effect of inductive reactance, capacitive reactance, and resistance in an AC series circuit is known as _____________. A. reactance B. total reactance C. impedance D. resonance

Description : The combined effect of inductive reactance, capacitive reactance, and resistance in an AC series circuit is known as _____________. A. reactance B. total reactance C. impedance D. resonance

Last Answer : Answer: C

In a series-RLC circuit, what is the condition of the circuit if there is high impedance, low current, and low reactance voltages

Description : In a series-RLC circuit, what is the condition of the circuit if there is high impedance, low current, and low reactance voltages

Last Answer : Nonresonant (circuit is either above or below resonance)

What is the difference between calculating impedance in a series ac circuit and in a parallel ac circuit?

Description : What is the difference between calculating impedance in a series ac circuit and in a parallel ac circuit?

Last Answer : In a series circuit impedance is calculated from the values of resistance and reactance. In a parallel circuit, the values of resistive current and reactive current must be used to calculate total impedance.

What type of gating signal is used in single phase ac voltage controller with RL load?

Description : What type of gating signal is used in single phase ac voltage controller with RL load?

Last Answer : High frequency carrier gating signal is used for single phase ac voltage controller with RL load.

What is the control range of firing angle inac voltage controller with RL load?

Description : What is the control range of firing angle inac voltage controller with RL load?

Last Answer : The control range is Φ< α

In an amplifier the collector voltage equals the full V+ of 28 V instead of the normal 12 V which of the following can be the trouble? A) RL is open B) Cc is open C) RE is open D) CE is shorted.

Description : In an amplifier the collector voltage equals the full V+ of 28 V instead of the normal 12 V which of the following can be the trouble? A) RL is open B) Cc is open C) RE is open D) CE is shorted.

Last Answer : B) Cc is open

Decreasing the frequency in a capacitive circuit while maintaining a constant circuit voltage, will result in a/an _____________. A. increase in apparent power B. decrease in circuit current C. decrease in capacitive reactance D. decrease in total impedance

Description : Decreasing the frequency in a capacitive circuit while maintaining a constant circuit voltage, will result in a/an _____________. A. increase in apparent power B. decrease in circuit current C. decrease in capacitive reactance D. decrease in total impedance

Last Answer : Answer: B

Which of the electrical properties listed will always be the same for each component in a parallel circuit? A. Impedance B. Current C. Resistance D. Voltage

Description : Which of the electrical properties listed will always be the same for each component in a parallel circuit? A. Impedance B. Current C. Resistance D. Voltage

Last Answer : Answer: D

When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only and a low resistance meter for DC measurements C. whenever a low impedance meter is not available, regardless of the components being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Description : When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only ... being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Last Answer : Answer: D

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Description : ___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Last Answer : A. Psophometer

Voltage measurement in a high impedance circuit requires a voltmeter with

Description : Voltage measurement in a high impedance circuit requires a voltmeter with

Last Answer : high input impedance

. What characteristic of an RL circuit allows it to act as an integrator?

Description : . What characteristic of an RL circuit allows it to act as an integrator?

Last Answer : The ability of the inductor to oppose a change in current.

Draw series R-L-C circuit and describe resonance.

Description : Draw series R-L-C circuit and describe resonance. 

Last Answer : Series R-L-C circuit:  Explanation of Series R-L-C Resonance circuit: A series circuit containing resistance, inductance and capacitance, is said to be resonant when the circuit power ... , and as we are analyzing a series RLC circuit this resonance frequency produces a Series Resonance.

Draw circuit diagram of voltage divider biasing list two advantages of voltage divider biasing of BJT.

Description : Draw circuit diagram of voltage divider biasing list two advantages of voltage divider biasing of BJT.

Last Answer : Two advantages of voltage divider biasing of BJT. 1. It is very simple method of transistor biasing. 2. The biasing conditions can be very easily set. 3. there is no loading of ... 5. The resistor RE introduces a negative feedback. So all the advantages of negative feedback are obtained. 

Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance

Description : Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance

Last Answer : Parameter Common Base Common Collector Current gain Low (About 1) High (1+β) Voltage gain High 1  Input impedance  Low High Output impedance High Low

A 400/200 volts transformer has pu impedance of 0.05. The HV side voltage required to circulate full load...

Description : A 400/200 volts transformer has pu impedance of 0.05. The HV side voltage required to circulate full load current during short circuit test is

Last Answer : A 400/200 volts transformer has pu impedance of 0.05. The HV side voltage required to circulate full load current during short circuit test is 20 V

A travelling wave of surge resistance, Ro on a transmission line is terminated by a load resistance, RL...

Description : A travelling wave of surge resistance, Ro on a transmission line is terminated by a load resistance, RL. If RL > Ro then there is (A) no reflected wave (B) partial reflection of reversal ... (C) partial reflection of reversal of voltage only (D) reflection of reversal of both current and voltage

Last Answer : A travelling wave of surge resistance, Ro on a transmission line is terminated by a load resistance, RL. If RL > Ro then there is partial reflection of reversal of current only

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

Compare series and parallel circuit in terms of voltage and current.

Description :  Compare series and parallel circuit in terms of voltage and current.

Last Answer : Series circuits Parallel circuits Only ONE path for current to flow in a closed circuit Number of path for current to flow in a closed circuit Current remains the SAME ... Voltage is DIFFERENT across each component Voltage remains the same across each component of the circuit

Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage

Description : Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

Last Answer : Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

In a series resonant circuit, maximum voltage across L occurs at

Description : In a series resonant circuit, maximum voltage across L occurs at  (a) Resonant frequency (b) Slightly below resonant frequency (c) Slightly above resonant frequency (d) At a frequency where I is maximum

Last Answer : In a series resonant circuit, maximum voltage across L occurs at Slightly above resonant frequency

A series R-L circuit is suddenly connected to d.c. voltage source of V volts. The current in this series ...

Description : A series R-L circuit is suddenly connected to d.c. voltage source of V volts. The current in this series circuit, just after the switch is closed, is equal to (1) Zero (2) V/L (3) V/C (4) V.L/C 

Last Answer : When is a series RLC circuit is over damped

The per unit impedance of a circuit element is 0.30. If the base kV and base MVA are halved, then the new...

Description : The per unit impedance of a circuit element is 0.30. If the base kV and base MVA are halved, then the new value of the per unit impedance of the circuit element will be:  (A) 0.3 (B) 0.6 (C) 0.003 (D) 0.006 

Last Answer : 3

Draw waveform for standing waves on an open and shorted line. Prove that impedance is inverted at every quarter wavelength interval.

Description : Draw waveform for standing waves on an open and shorted line. Prove that impedance is inverted at every quarter wavelength interval.

Last Answer : Waveform- Explanation When the transmission line is short circuited voltage is zero and current is maximum.The variation is according to the wavelength. When the ... The pattern repeats for every half wavelength. Thus impedance is inverted at every quarter wavelength interval.

State different types of power in ac circuits. Write the expression and units for the same. Draw the power triangle.

Description : State different types of power in ac circuits. Write the expression and units for the same. Draw the power triangle. 

Last Answer : i) Active Power (P):- The active power is defined as the average power Pavg taken by or consumed by the given circuit.   ii) Reactive Power (Q):-  The reactive power is defined as the product of ... values of voltage (v) and current (I) it is given by    iv) Power Triangle: