What is the material of slip ring?

What is the material of slip ring? 
by

1 Answer

Answer :

Alloy steel  
by

Related questions

If an AC generator experiences voltage failure, the cause may be _____________. A. an open in the field circuit B. the brushes shifting out of the neutral plane C. excessive locked-rotor current D. a rotating slip ring

Description : If an AC generator experiences voltage failure, the cause may be _____________. A. an open in the field circuit B. the brushes shifting out of the neutral plane C. excessive locked-rotor current D. a rotating slip ring

Last Answer : Answer: A

Which of the following statements represents the FIRST step in seating new brushes on slip rings? A. Wrap sandpaper around the slip rings and slide it back and forth between the brushes and the slip rings. B. Press the brushes against the slip ring with a wood block. C. Increase brush pressure and run at no load for 3 to 4 hours. D. Apply seating compound under the brushes and run at no load for 2 hours.

Description : Which of the following statements represents the FIRST step in seating new brushes on slip rings? A. Wrap sandpaper around the slip rings and slide it back and forth between the brushes and the slip rings. B. ... to 4 hours. D. Apply seating compound under the brushes and run at no load for 2 hours.

Last Answer : Answer: A

A degree of control over the speed of a slip ring induction motor can be obtained by _____________. A. adjusting governor linkage B. changing the number of phases to the motor C. inserting resistance into the stator circuit D. inserting resistance into the rotor circuit

Description : A degree of control over the speed of a slip ring induction motor can be obtained by _____________. A. adjusting governor linkage B. changing the number of phases to the motor C. inserting resistance into the stator circuit D. inserting resistance into the rotor circuit

Last Answer : Answer: D

Slip ring induction motor advantages and disadvantages compared to squirrel cage motors?

Description : Slip ring induction motor advantages and disadvantages compared to squirrel cage motors?

Last Answer : Advantages: High starting torque with low starting current Smooth acceleration under heavy loads No abnormal heating during starting Good running characteristics after external rotor resistances are cut out ... cage motors The speed regulation is poor when run with resistance in the rotor circuit

Mention different types of speed control of slip ring induction motor?

Description : Mention different types of speed control of slip ring induction motor?

Last Answer : a) By changing supply frequency b) By changing the number of stator poles c) By rotor rheostat control d) By operating two motors in cascade

How the slip ring motor is started?

Description : How the slip ring motor is started?

Last Answer : The slip ring motor is started by using rotor resistance starter. The starter consists of star connected resistance to slip rings. While starting the full resistance is included in the rotor circuit to ... running condition the slip rings are shorted and so it is equivalent to squirrel cage rotor.

What are the advantages of slip ring motor over squirrel cage motor?

Description : What are the advantages of slip ring motor over squirrel cage motor?

Last Answer : 1. The starting torque can be varied by adding resistance to rotor. 2. The speed of the machine can be varied by injecting an emf through slip rings to the rotor.

What is the purpose of connecting external resistors to slip ring Induction motor?

Description : What is the purpose of connecting external resistors to slip ring Induction motor?

Last Answer : It increases starting torque and decreases starting current.

How cooling is done for slip ring and brush gear?

Description : How cooling is done for slip ring and brush gear? 

Last Answer : A centrifuge fan is mounted on the shaft in between two slip rings for ventilation of the slip rings and brush gear.

Where is a slip ring used and where is a commutator used?

Description : Where is a slip ring used and where is a commutator used?

Last Answer : Slip rings are commonly found in slip ring motors, electrical generators for alternating current systems and alternators. They can be used on any rotating object to transfer power. A commutator is a common ... in the moving coil of a motor's armature, a steady rotating force (torque) is produced.

Which component is mainly used in a DC generator: a.slip ring b. commutator c. magnet d. coil

Description : Which component is mainly used in a DC generator: a.slip ring b. commutator c. magnet d. coil

Last Answer : b. commutator

Which one is not present in AC generator: a. Armature b. magnet c. slip ring d. commutator

Description : Which one is not present in AC generator: a. Armature b. magnet c. slip ring d. commutator

Last Answer : c. slip ring

State the function of following parts of slip ring induction motor: (i) Slip ring (ii) Fan (iii) Brushes (iv) Frame

Description : State the function of following parts of slip ring induction motor: (i) Slip ring (ii) Fan (iii) Brushes (iv) Frame

Last Answer : Sr. No. Name of part Function 1 Slip ring 1) The rotor winding terminals are permanently connected to the slip rings. 2) Connects external resistance to rotor circuit through ... It provides mechanical support to the entire internal parts of motor. 2) Protects the inner parts.

Compare squirrel cage induction motor and slip ring induction motor any four points.

Description : Compare squirrel cage induction motor and slip ring induction motor any four points.

Last Answer : Comparison Between Squirrel Cage Induction Motor and Slip Ring Induction Motor: Sr. No. Squirrel Cage Induction Motor Slip Ring Induction Motor 1 Rotor is in the form of short circuited bars ... drive e.g. Lathe machine. Used where high starting torque is required e.g. Lifts.

Develop power and control diagram for secondary frequency acceleration starter of slip ring induction motor.

Description : Develop power and control diagram for secondary frequency acceleration starter of slip ring induction motor. 

Last Answer : Power and Control Circuit diagram for secondary frequency acceleration starter of slip ring induction motor:

Draw power and control circuit for definite time-limit starter for slip-ring induction motor. Explain its working.

Description : Draw power and control circuit for definite time-limit starter for slip-ring induction motor. Explain its working.

Last Answer : Definite Time-limit Starter for Slip-ring Induction Motor: This starter is used for automatic control of acceleration of slip-ring induction motor at the time of starting. In this starter, the ... each phase, shorting the rotor winding terminals and final acceleration of the motor takes place. 

The stator of a 415V, 50 Hz, 4-pole slip ring Induction Motor is excited by rated frequency with slip rings open

Description : The stator of a 415V, 50 Hz, 4-pole slip ring Induction Motor is excited by rated frequency with slip rings open circuited. The rotor is made to rotate at a speed of 600 rpm in the opposite direction to the ... frequency of induced voltage across slip ring is A) 30 Hz B) 70 Hz C) 20 Hz D) 35 Hz

Last Answer : The stator of a 415V, 50 Hz, 4-pole slip ring Induction Motor is excited by rated frequency with slip rings open circuited. The rotor is made to rotate at a speed of 600 rpm in the opposite direction to the normal direction, The frequency of induced voltage across slip ring is 70 Hz

A three phase slip ring induction motor is fed from the rotor side with stator winding short circuited stator is:

Description : A three phase slip ring induction motor is fed from the rotor side with stator winding short circuited stator is: (1) Slip frequency (2) Supply frequency (3) Frequency corresponding to rotor speed (4) Zero

Last Answer : A three phase slip ring induction motor is fed from the rotor side with stator winding short circuited stator is: Slip frequency

A three phase slip ring induction motor with chopper controlled resistance has its torque

Description : A three phase slip ring induction motor with chopper controlled resistance has its torque proportional to   (a) Rotor current (b) Stator resistance (c) Square of rotor current (d) Square root of rotor current 

Last Answer : A three phase slip ring induction motor with chopper controlled resistance has its torque proportional to Square of rotor current

The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted

Description : The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be

Last Answer : The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be 0.5 Ohm

In a 3-phase slip-ring induction motor, the slip at some speed is 0.05. The speed is reduced by inserting an

Description : In a 3-phase slip-ring induction motor, the slip at some speed is 0.05. The speed is reduced by inserting an external resistance in the rotor circuit and the slip is 0.15. If the rotor winding resistance per phase is 0.2 Ω, the external resistance is (A) 0.2 Ω (B) 0.3 Ω (C) 0.4 Ω (D) 0.5 Ω

Last Answer : In a 3-phase slip-ring induction motor, the slip at some speed is 0.05. The speed is reduced by inserting an external resistance in the rotor circuit and the slip is 0.15. If the rotor winding resistance per phase is 0.2 Ω, the external resistance is 0.3 Ω

A 3 phase 50 Hz induction motor has full load speed of 970 rpm. Calculate no of poles and slip frequency.

Description : A 3 phase 50 Hz induction motor has full load speed of 970 rpm. Calculate no of poles and slip frequency.

Last Answer : The number of poles in an induction motor can be calculated using the following formula: No. of poles = (120 * frequency) / speed In this case, the number of poles would be calculated as follows: No. of poles = ( ... ) - 50 Hz = 8.08 Hz So the motor has 6 poles and a slip frequency of 8.08 Hz.

The main purpose of an electric space heater installed in a large AC generator is to _____________. A. keep the lube oil warm for quick starting B. prevent moisture from condensing in the windings when the machine is shutdown C. prevent the windings from becoming brittle D. prevent acidic pitting of the slip rings

Description : The main purpose of an electric space heater installed in a large AC generator is to _____________. A. keep the lube oil warm for quick starting B. prevent moisture from condensing in the ... is shutdown C. prevent the windings from becoming brittle D. prevent acidic pitting of the slip rings

Last Answer : Answer: B

An AC generator operating in parallel loses its excitation without tripping the circuit breaker. This will __________. A. not affect the faulty generator due to the compensation of the other generators B. cause the slip rings to melt C. cause a low voltage differential to develop between the armature and the bus D. cause high currents to be induced in the field windings

Description : An AC generator operating in parallel loses its excitation without tripping the circuit breaker. This will __________. A. not affect the faulty generator due to the compensation of the other generators B. ... between the armature and the bus D. cause high currents to be induced in the field windings

Last Answer : Answer: D

An alternator will fail to produce line voltage as a result of _____________. A. a closed circuit breaker B. oxidized slip rings C. improperly staggered brushes D. exciter generator failure

Description : An alternator will fail to produce line voltage as a result of _____________. A. a closed circuit breaker B. oxidized slip rings C. improperly staggered brushes D. exciter generator failure

Last Answer : Answer: D

A four pole, 60 Hz, three-phase synchronous motor comes up to 1760 RPM when started as an induction motor. What is the percent slip after the rotor field is energized? A. 0 B. 1.1 C. 2.2 D. 3.3

Description : A four pole, 60 Hz, three-phase synchronous motor comes up to 1760 RPM when started as an induction motor. What is the percent slip after the rotor field is energized? A. 0 B. 1.1 C. 2.2 D. 3.3

Last Answer : Answer: A

Which of the following statements describes what will occur if the motor shown in the illustration is required to carry 150% of full load? EL-0056 A. The primary counter emf will be increased. B. The stator current will increase. C. The slip will decrease. D. The slip value, stator current curve, and torque curve will all coincide.

Description : Which of the following statements describes what will occur if the motor shown in the illustration is required to carry 150% of full load? EL-0056 A. The primary counter emf will be increased. B. ... slip will decrease. D. The slip value, stator current curve, and torque curve will all coincide.

Last Answer : Answer: B

The torque and current curves for a three-phase induction motor with a cage rotor, are shown in the illustration. Which of the following statements is true concerning the depicted curves? EL-0056 A. As slip increases, rotor reactance decreases. B. The pullout point on the torque curve is about seven times the normal full load torque value. C. At stand still, stator current is 150% of normal. D. If the motor is loaded to the point where 40% slip has resulted, it will stall.

Description : The torque and current curves for a three-phase induction motor with a cage rotor, are shown in the illustration. Which of the following statements is true concerning the depicted curves? EL-0056 A. As slip ... D. If the motor is loaded to the point where 40% slip has resulted, it will stall.

Last Answer : Answer: D

Which of the following materials is recommended for finishing the slip rings after grinding or turning? A. grade 00 sandpaper B. canvas wiper C. crocus cloth D. smooth file

Description : Which of the following materials is recommended for finishing the slip rings after grinding or turning? A. grade 00 sandpaper B. canvas wiper C. crocus cloth D. smooth file

Last Answer : Answer: C

A four-pole 60-hertz induction motor has a synchronous speed of 1800 RPM and a slip of 4 percent at full load. What will be its full load speed? A. 1728.0 RPM B. 1730.7 RPM C. 1800.0 RPM D. 1872.0 RPM

Description : A four-pole 60-hertz induction motor has a synchronous speed of 1800 RPM and a slip of 4 percent at full load. What will be its full load speed? A. 1728.0 RPM B. 1730.7 RPM C. 1800.0 RPM D. 1872.0 RPM

Last Answer : Answer: A

A four-pole, 60 cycle, squirrel-cage motor has a full load speed of 1725 RPM. What will be the percent of slip at full load? A. 4.16 B. 4.34 C. 95.66 D. 95.84

Description : A four-pole, 60 cycle, squirrel-cage motor has a full load speed of 1725 RPM. What will be the percent of slip at full load? A. 4.16 B. 4.34 C. 95.66 D. 95.84

Last Answer : Answer: A

In the illustration, the signal from the device connected to terminals 18 and 19 is __________. EL-0046 A. prime mover speed feedback B. loss of control alarm when comparing with the input signal from the resistor at the top of the speed sensing circuit card C. hall effect current to detect slip between the prime mover and the alternator D. to shut down the prime mover if overspeeding

Description : In the illustration, the signal from the device connected to terminals 18 and 19 is __________. EL-0046 A. prime mover speed feedback B. loss of control alarm when comparing with the input signal ... slip between the prime mover and the alternator D. to shut down the prime mover if overspeeding

Last Answer : Answer: A

What is the rotor speed of a four pole, 60 cycle, induction motor operating at full load with 3% slip? A. 270 RPM B. 540 RPM C. 873 RPM D. 1746 RPM

Description : What is the rotor speed of a four pole, 60 cycle, induction motor operating at full load with 3% slip? A. 270 RPM B. 540 RPM C. 873 RPM D. 1746 RPM

Last Answer : Answer: D

A three-phase, squirrel cage, induction motor will run hot due to _____________. A. open stator coils B. high power factor C. dirty or corroded slip rings D. reversed commutating poles

Description : A three-phase, squirrel cage, induction motor will run hot due to _____________. A. open stator coils B. high power factor C. dirty or corroded slip rings D. reversed commutating poles

Last Answer : Answer: A

To properly seat the brushes on slip rings, you should use ____________. A. sand paper B. crocus cloth C. emery cloth D. all of the above

Description : To properly seat the brushes on slip rings, you should use ____________. A. sand paper B. crocus cloth C. emery cloth D. all of the above

Last Answer : Answer: A

The reversal of an AC, three-phase, induction motor is accomplished by ______________. A. changing all three motor leads B. reversing the position of the slip rings C. interchanging any two of the three motor leads D. interchanging any two brushes

Description : The reversal of an AC, three-phase, induction motor is accomplished by ______________. A. changing all three motor leads B. reversing the position of the slip rings C. interchanging any two of the three motor leads D. interchanging any two brushes

Last Answer : Answer: C

Routine maintenance of a ship's service alternator should include ______________. A. changing the pedestal bearing insulation yearly B. megger testing of all rectifying diodes C. lubricating excitation slip rings D. periodic cleaning of the air filters or screens

Description : Routine maintenance of a ship's service alternator should include ______________. A. changing the pedestal bearing insulation yearly B. megger testing of all rectifying diodes C. lubricating excitation slip rings D. periodic cleaning of the air filters or screens

Last Answer : Answer: D

The main purpose of an electric space heater installed in a large AC generator is to _____________. A. prevent the windings from becoming brittle B. prevent moisture from condensing in the windings during shutdown C. prevent acidic pitting of the slip rings D. keep the lube oil warm for quick starting

Description : The main purpose of an electric space heater installed in a large AC generator is to _____________. A. prevent the windings from becoming brittle B. prevent moisture from condensing in the windings during ... C. prevent acidic pitting of the slip rings D. keep the lube oil warm for quick starting

Last Answer : Answer: B

Which of the following statements is true concerning the operating characteristics of a squirrel-cage motor? A. Rotor slip is dependent upon the motor load. B. An increase in motor load results in less slip. C. A decrease in rotor speed results in less generated current. D. A decrease in rotor speed produces a weaker magnetic field.

Description : Which of the following statements is true concerning the operating characteristics of a squirrel-cage motor? A. Rotor slip is dependent upon the motor load. B. An increase in motor load results in ... results in less generated current. D. A decrease in rotor speed produces a weaker magnetic field.

Last Answer : Answer: A

Erratic operation of the devices represented in the diagrams shown in the illustration could be traced to ____________. EL-0092 A. improper contact at 'R' slip rings or 'S' connections B. a low three-phase voltage supply C. improper contact at 'S' slip rings or 'R' connections D. a high three-phase voltage supply

Description : Erratic operation of the devices represented in the diagrams shown in the illustration could be traced to ____________. EL-0092 A. improper contact at 'R' slip rings or 'S' connections B. a low three- ... . improper contact at 'S' slip rings or 'R' connections D. a high three-phase voltage supply

Last Answer : Answer: A

If an induction motor were to be operated at 90% rated voltage, _____________. A. there would be an increase in starting torque B. starting current would increase slightly C. synchronous speed would decrease slightly D. the slip would increase

Description : If an induction motor were to be operated at 90% rated voltage, _____________. A. there would be an increase in starting torque B. starting current would increase slightly C. synchronous speed would decrease slightly D. the slip would increase

Last Answer : Answer: D

In actual applications, electrical connections to 'R1-R2' of figure 'A' and to 'R1-R2- R3' of figure 'B' shown in the illustration are made by ______________. EL-0092 A. soldered contacts B. spliced and taped connections C. slip rings and brushes D. solderless crimp-on connectors

Description : In actual applications, electrical connections to 'R1-R2' of figure 'A' and to 'R1-R2- R3' of figure 'B' shown in the illustration are made by ______________. EL-0092 A. soldered contacts B. spliced and taped connections C. slip rings and brushes D. solderless crimp-on connectors

Last Answer : Answer: C

Using illustrated chart, when will the power factor be least efficient? EL-0006 A. When the motor is operating at full load. B. When the percentage of slip is greatest. C. When there is no load on the motor. D. the power factor is the same from no-load to locked rotor.

Description : Using illustrated chart, when will the power factor be least efficient? EL-0006 A. When the motor is operating at full load. B. When the percentage of slip is greatest. C. When there is no load on the motor. D. the power factor is the same from no-load to locked rotor.

Last Answer : Answer: C

The synchronous speed of an induction motor is the ________. A. speed at which the rotor turns B. speed of the rotating field C. frequency of the rotor current D. slip in per cent of rotor RPM

Description : The synchronous speed of an induction motor is the ________. A. speed at which the rotor turns B. speed of the rotating field C. frequency of the rotor current D. slip in per cent of rotor RPM

Last Answer : Answer: B

The difference between the synchronous speed of an induction machine and its operating speed (slip) may be correctly expressed _____________. A. as a percent of synchronous speed B. as a decimal fraction of synchronous speed C. directly in revolutions per minute D. as all of the above

Description : The difference between the synchronous speed of an induction machine and its operating speed (slip) may be correctly expressed _____________. A. as a percent of synchronous speed B. as a decimal fraction of synchronous speed C. directly in revolutions per minute D. as all of the above

Last Answer : Answer: A

The rotor of a synchronous motor operates in synchronism with the rotating field because ______________. A. of the amortisseur windings B. the rotor is magnetically locked into step with the rotating magnetic field by the excitation current C. the field strength varies directly with rotor slip D. the stator flux rotates in the opposite direction

Description : The rotor of a synchronous motor operates in synchronism with the rotating field because ______________. A. of the amortisseur windings B. the rotor is magnetically locked into step with the ... field strength varies directly with rotor slip D. the stator flux rotates in the opposite direction

Last Answer : Answer: B

A generator has been exposed to water and is being checked for its safe operation. Therefore, it is necessary to _______________. A. check for shorted coils with a growler B. take moisture readings with a hydrometer C. test insulation values with a megger D. ground the commutator, or slip rings and run it at half load for 12 hours

Description : A generator has been exposed to water and is being checked for its safe operation. Therefore, it is necessary to _______________. A. check for shorted coils with a growler B. take moisture readings with a ... a megger D. ground the commutator, or slip rings and run it at half load for 12 hours

Last Answer : Answer: C

A synchronous motor maintains synchronism with the rotating field because _____________. A. field strength varies directly with rotor slip B. DC current applied to the rotor coils causes the rotor magnets to lock in with the rotating flux of the stator C. the stator poles are dragged around due to the flux created by the excitation current D. the stator flux rotates in the opposite direction

Description : A synchronous motor maintains synchronism with the rotating field because _____________. A. field strength varies directly with rotor slip B. DC current applied to the rotor coils causes the rotor ... the flux created by the excitation current D. the stator flux rotates in the opposite direction

Last Answer : Answer: B