Description : Seating the brushes on a D.C. motor is first accomplished using ________________. A. a file for cutting the approximate curvature followed by sandpaper for the final fit B. sandpaper with the motor not ... for the finishing cut D. course lapping compound, followed by a medium and then a fine grade
Last Answer : Answer: B
Description : Which of the following materials is recommended for finishing the slip rings after grinding or turning? A. grade 00 sandpaper B. canvas wiper C. crocus cloth D. smooth file
Last Answer : Answer: C
Description : Voltage generated by most AC generators is fed from the machine to the bus by means of ____________. A. brushes on a commutator B. brushes on slip rings C. slip rings on a commutator D. direct connections from the stator
Last Answer : Answer: D
Description : Brushless generators are designed to operate without the use of ___________. A. brushes B. slip rings C. commutators D. all of the above
Description : An alternator will fail to produce line voltage as a result of _____________. A. a closed circuit breaker B. oxidized slip rings C. improperly staggered brushes D. exciter generator failure
Description : If an alternator is to be inactive for a considerable period of time, which of the following actions should be taken? A. It should be disconnected from the prime mover and raised off its bearing supports ... . D. The windings and collector rings should be protected with a thin coat of grease or oil.
Description : Which of the following statements represents the FIRST step in seating new brushes on slip rings? A. Wrap sandpaper around the slip rings and slide it back and forth between the brushes and the slip rings. B. ... to 4 hours. D. Apply seating compound under the brushes and run at no load for 2 hours.
Last Answer : Answer: A
Description : The reversal of an AC, three-phase, induction motor is accomplished by ______________. A. changing all three motor leads B. reversing the position of the slip rings C. interchanging any two of the three motor leads D. interchanging any two brushes
Description : In actual applications, electrical connections to 'R1-R2' of figure 'A' and to 'R1-R2- R3' of figure 'B' shown in the illustration are made by ______________. EL-0092 A. soldered contacts B. spliced and taped connections C. slip rings and brushes D. solderless crimp-on connectors
Description : Which of the following statements is true concerning all three-phase alternators? A. Each has three separate but identical armature windings acted on by one system of rotating magnets. B. Each has one ... The three phases always provide power to the load through three sets of slip rings and brushes.
Description : In an AC generator, direct current from a separate source is passed through the windings of the rotor _____________. A. by means of slip rings and brushes B. by means of a commutator C. by means of rotating bar magnet D. to minimize the danger of arc over
Description : In an induction motor, rotor currents are circulated in the rotor by _____________. A. slip rings and brushes B. an armature and brushes C. inductive reaction of the rotating stator field D. external variable resistors
Description : What are the materials used to manufacture the brushes for slip rings of an induction motor?
Last Answer : A:The slip rings are made of brass and phosphor bronze. The brushes are made of metal graphite which is an alloy of copper and carbon.
Description : The current from the stator of an alternator is taken out to the external load circuit through (A) slip rings. (B) commutator segments. (C) solid connections. (D) carbon brushes.
Last Answer : (C) solid connections.
Description : Controller contacts should be routinely cleaned by ________. A. blowing with compressed air B. filing with a bastard file C. wiping with a clean dry cloth D. dressing with crocus cloth
Description : For routine cleaning of a commutator, you should apply _____________. A. course sandpaper in a slow back and forth motion across the commutator slots B. an emery cloth parallel to the axis of the machine C. a canvas wiper to the machine while running D. cotton swabs between the commutator bars
Description : The compound used in manufacture of emery paper or sand paper is
Last Answer : silica.
Description : While starting a main propulsion synchronous motor, the ammeter pegs out at maximum and then returns to the proper value after synchronization. This indicates the _____________. A. motor has started ... field windings are grounded C. slip rings are dirty D. power transmission cables are grounded
Description : Erratic operation of the devices represented in the diagrams shown in the illustration could be traced to ____________. EL-0092 A. improper contact at 'R' slip rings or 'S' connections B. a low three- ... . improper contact at 'S' slip rings or 'R' connections D. a high three-phase voltage supply
Description : Which of the following are the parts of a DC generator that convert the AC in the armature to DC in the external circuit. Are these parts the: w) field poles x) slip rings and the brushes y) commutator and the brushes z) armature and the core
Last Answer : ANSWER: Y -- COMMUTATOR AND THE BRUSHES
Description : Oxide layer formed on the non-ferrous metal surface after its annealing is (A) Removed by acid pickling (B) Hammered into the surface (C) Removed with coarse emery cloth
Last Answer : Option A
Description : Which of the following statements concerning the maintenance of solid-silver contacts in relays and auxiliary control circuits is correct? A. When necessary, they should always be dressed with a ... they should be held together with moderate pressure while emery paper is drawn between the contacts.
Description : If an AC generator experiences voltage failure, the cause may be _____________. A. an open in the field circuit B. the brushes shifting out of the neutral plane C. excessive locked-rotor current D. a rotating slip ring
Description : Which of the following precautions should you take when securing propulsion generators and motors for an extended period of time? A. Disconnect the brush pigtails from their contacts and circulate air ... Lift the brushes from commutator collector rings and circulate cool dry air through the units.
Description : Chattering of the collector ring brushes on a generator may be remedied by _____________. A. lubricating brush holders B. reinsulating the brushes C. cleaning the collector rings D. increasing length of pigtail
Description : Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature
Description : When an alternator is to remain idle for even a few days _________________. A. lift the brushes and disconnect the pigtails B. insulate the collector rings with strips of cardboard C. energize the heater circuit D. open the equalizing bus disconnect switch
Description : Sparking at the brushes of a DC propulsion motor can be the result of ____________. A. improper brush pressure B. improper brush seating C. reversed interpole polarity D. all of the above
Description : Etched or burned bands on the contact faces of the brushes in a direct current generator can be caused by ____________. A. high mica segments B. copper drag on the commutator C. brushes improperly positioned D. copper embedded in the brushes
Description : An open armature connection in a DC propulsion motor could be caused by ____________. A. low-load operation B. clogged ventilation ducts C. sparking at the brushes D. a grounded shunt field coil
Description : The main purpose of an electric space heater installed in a large AC generator is to _____________. A. keep the lube oil warm for quick starting B. prevent moisture from condensing in the ... is shutdown C. prevent the windings from becoming brittle D. prevent acidic pitting of the slip rings
Description : An AC generator operating in parallel loses its excitation without tripping the circuit breaker. This will __________. A. not affect the faulty generator due to the compensation of the other generators B. ... between the armature and the bus D. cause high currents to be induced in the field windings
Description : A three-phase, squirrel cage, induction motor will run hot due to _____________. A. open stator coils B. high power factor C. dirty or corroded slip rings D. reversed commutating poles
Description : Routine maintenance of a ship's service alternator should include ______________. A. changing the pedestal bearing insulation yearly B. megger testing of all rectifying diodes C. lubricating excitation slip rings D. periodic cleaning of the air filters or screens
Description : The main purpose of an electric space heater installed in a large AC generator is to _____________. A. prevent the windings from becoming brittle B. prevent moisture from condensing in the windings during ... C. prevent acidic pitting of the slip rings D. keep the lube oil warm for quick starting
Description : A generator has been exposed to water and is being checked for its safe operation. Therefore, it is necessary to _______________. A. check for shorted coils with a growler B. take moisture readings with a ... a megger D. ground the commutator, or slip rings and run it at half load for 12 hours
Description : Which of the following physical characteristics does a wound-rotor induction motor possess that a squirrel cage motor does not? A. Slip rings B. End rings C. A centrifugal switch D. End plates
Description : What are slip rings?
Last Answer : The slip rings are made of copper alloys and are fixed around the shaft insulating it. Through these slip rings and brushes the rotor winding can be connected to external circuits.
Description : What are the routines checks on slip rings?
Last Answer : a. Correct mV drops brush to be used. b. Brush tension adjustment. c. Air cleaning to reduce leakage current. d. Brush bedding before use. e. Field polarity change every 6 months.
Description : State the function of following parts of slip ring induction motor: (i) Slip ring (ii) Fan (iii) Brushes (iv) Frame
Last Answer : Sr. No. Name of part Function 1 Slip ring 1) The rotor winding terminals are permanently connected to the slip rings. 2) Connects external resistance to rotor circuit through ... It provides mechanical support to the entire internal parts of motor. 2) Protects the inner parts.
Description : The 'dielectric constant' is a numerical value indicating the effectiveness of a dielectric material in comparison to that of a standard, which is _______________. A. paper or cloth B. glass or mica C. plastic or Teflon D. dry air or a vacuum
Description : Which of the following statements best describes the material known as varnished cambric? A. Felted asbestos sealed with varnish. B. Cotton cloth coated with insulating varnish. C. Rubber ... Paper impregnated with mineral oil, specially wrapped with nonmetallic tape, and coated with varnish.
Description : What are the benefits of leather seat covers versus cloth?
Last Answer : Leather seat covers will feel better and have a better look, but can also be freezing cold in the winter and blazing hot in the summer. I
Description : Are leather seat covers more durable then cloth?
Last Answer : Not always, leather is easily ripped by sharp objects, while fabric is easily stained.
Description : Rexine (also called artificial leather), which is used for making table cover, automobile seat cover, shoes etc. is made by coating thick cloth with molten (A) Teflon (B) Bakelite (C) SBR (D) PVC
Last Answer : (D) PVC
Description : How should I trim my extra large crocus which is pushing through my lanai screen?
Last Answer : Crocus are bulbs. You will have to dig up the bulbs and thin them. Next time replant them farther from your lanai.
Description : -when can I cut the crocus leaves?
Last Answer : Cut your lawn. What remains of the crocus leaves will brown off and come out easily.
Description : Give reason: Split rings are used instead of slip rings to construct DC dynamo
Last Answer : Split rings make the current to flow in the same direction in the external circuit in both cycles.
Description : What is the purpose of the slip rings?
Last Answer : To conduct the currents induced in the armature to an external load.
Description : In D.C. generators, current to the external circuit from armature is given through (a) commutator (b) solid connection (c) slip rings (d) none of above
Last Answer : Ans: a