What is the problem anticipated due to CT saturation?

Question

What is the problem anticipated due to CT saturation?

asked Nov 17, 2021 by anonymous

1 Answer

Related questions

A 65 years-old woman arrived for dental therapy. The answered questionnaire shows that she is suffering from severe cirrhosis. The problem that can be anticipated in the routine dental therapy is: A. Extreme susceptibility to pain B. Tendency towards prolonged haemorrhage C. Recurring oral infection D. Increased tendency to syncope E. Difficulty in achieving adequate local anaesthesia

Description : A 65 years-old woman arrived for dental therapy. The answered questionnaire shows that she is suffering from severe cirrhosis. The problem that can be anticipated in the routine dental ... oral infection D. Increased tendency to syncope E. Difficulty in achieving adequate local anaesthesia

Last Answer : B. Tendency towards prolonged haemorrhage

Certain characteristics or circumstances may increase the susceptibility of assets to misappropriation. Opportunities to misappropriate assets increase due to the following except: a. Inventory items that are small in size, of high value, or in high demand. b. Known or anticipated future employee layoffs. c. Easily convertible assets, such as bearer bonds, diamonds, or computer chips. d. Fixed assets which are small in size, marketable, or lacking observable identification of ownership.

Description : Certain characteristics or circumstances may increase the susceptibility of assets to misappropriation. Opportunities to misappropriate assets increase due to the following except: a. Inventory items that ... which are small in size, marketable, or lacking observable identification of ownership.

Last Answer : Certain characteristics or circumstances may increase the susceptibility of assets to misappropriation. Opportunities to misappropriate assets increase due to the following except: a. Inventory items that ... which are small in size, marketable, or lacking observable identification of ownership.

A control system with excessive noise, is likely to suffer from (a) saturation in amplifying stages (b) loss of gain (c) vibrations (d) oscillations

Description : A control system with excessive noise, is likely to suffer from (a) saturation in amplifying stages (b) loss of gain (c) vibrations (d) oscillations

Last Answer : Ans: A

Before servicing the device indicated as 'A' in panels #1 and #3 of the illustration, the device labeled 'CT' must __________. EL-0003 A. have the disconnected leads taped to prevent short circuiting. B. only be connected to multimeter on the ammeter setting C. be short circuited D. have one lead grounded to discharge static electricity for the prevention of damage to electronic components

Description : Before servicing the device indicated as 'A' in panels #1 and #3 of the illustration, the device labeled 'CT' must __________. EL-0003 A. have the disconnected leads taped to prevent ... D. have one lead grounded to discharge static electricity for the prevention of damage to electronic components

Last Answer : Answer: C

Difference between Current Transformer (CT) and Potential Transformer (PT)

Description : Difference between Current Transformer (CT) and Potential Transformer (PT)

Last Answer : Current Transformers (CT) and Potential Transformers (PT) are used to measure the current and voltage in a circuit of the order of hundreds of amperes and volts respectively. A CT has large number of ... and flux density vary over a wide range whereas in PT, they vary over a limited range only

What are the errors in CT?

Description : What are the errors in CT?

Last Answer : (a) Ratio error Percentage ratio error = [(Nominal ratio – Actual ratio)/Actual ratio] x 100 The value of transformation ratio is not equal to the turns ratio. (b) Phase angle error: Phase angle =180/ [(ImCos -I1Sin )/nIs]

Where wound type CT used and where not used?

Description : Where wound type CT used and where not used?

Last Answer : Used where low CT ratio req. Not used where high short ckt. Current exists.

Give the details of switchyard 220 kV CB, Isolator, CT, CVT and lightning arrestor.

Description : Give the details of switchyard 220 kV CB, Isolator, CT, CVT and lightning arrestor.

Last Answer : 220 kV SF6 Circuit Breaker 1. Make - ABB 2. Air pressure blocking a. Close Block - 17.3 bar. b. Open block - 16.7 bar. c. Auto reclose block - 19 bar. 3. SF6 pressure block a. Alarm - 5. ... , storage and erection. Rated voltage : 216 kV rms. Operating voltage : 184 kV rms.

Why CT operated over load relay is using for loads of high acceleration time upto 30 seconds? How it getting back?

Description : Why CT operated over load relay is using for loads of high acceleration time upto 30 seconds? How it getting back?

Last Answer : The saturable current transformers linearly transforms the current upto twice the set current, but above this value the transformer core gets saturated and the secondary current is proportionally less. Thus ... overload. When current reduces the core gets de-saturated, as material design is such.

How CT is connecting in ckt?

Description : How CT is connecting in ckt?

Last Answer : If the primary of CT is delta connected load the CT will be in star connection and vice versa. This is because to have square root 3 time compensation.

Why ICT are used?(INTERPOSING CT)

Description : Why ICT are used?(INTERPOSING CT)

Last Answer : To correct the system primary CT errors in case of high current faults out side CT zone (ICT’s primary CT is 800/1, but in fault current may go to thousands of amps. This ICT will take care of those errors. a) Matching the ratios. b) Matching the phase angle differences.

Why core balance CT is preferred over residual connected CT’s to sense earth fault in 6.6 kV feeders?

Description : Why core balance CT is preferred over residual connected CT’s to sense earth fault in 6.6 kV feeders?

Last Answer : a) To avoid relay mal-operation due to CT saturation b) Better sensitivity is got. c) High pickup and TMS avoided in IDMT earth fault relay.

What are the checks on CT & PT?

Description : What are the checks on CT & PT?

Last Answer : a) Polarity checks b) Insulation checks c) Ratio checks d) Knee point voltage (only for PS class CT)- magnetising characteristic test.

Where CT secondary of 1A we are using?

Description : Where CT secondary of 1A we are using?

Last Answer : For long distance current transmission, to reduce the IR drop.

What is the purpose of CT & PT?

Description : What is the purpose of CT & PT?

Last Answer : For transformation of current, voltage to a lower level for the purpose of Measurement, Protection and Control.

What is the standard CT polarity?

Description : What is the standard CT polarity?

Last Answer : Primary current enters at P1 and secondary current leaves at S2.

But is it advisable to keep the secondary of CT in open conditions? Will not induce very high voltage?

Description : But is it advisable to keep the secondary of CT in open conditions? Will not induce very high voltage?

Last Answer : If the CT has only one secondary winding, we should keep it always short cktd for safety, but if the CT has multiple secondary, then if one secondary voltage is kept limited by suitable loading, then the other secondary voltage is eventually limited proportionately.

A CT has 2 – secondary windings. If we use only one secondary winding can we keep the unused secondary winding short circuited?

Description : A CT has 2 – secondary windings. If we use only one secondary winding can we keep the unused secondary winding short circuited?

Last Answer : No. If it is short-circuited then the ratio will not get correctly. The turns of primary winding will be shared between 2 secondary windings. So the unused secondary winding should kept open.

What is over voltage interturn test for CT?

Description : What is over voltage interturn test for CT?

Last Answer : With secondary open, pass rated current in primary for 1 min. Then check secondary for insulation.

What is the operating point in the Magnetising characteristic of protection CT & measuring CT?

Description : What is the operating point in the Magnetising characteristic of protection CT & measuring CT?

Last Answer : Protection CT – Operation at ankle point only. Measuring CT – Operation from ankle to knee point

What are the errors of the following CT’ s 5p. 10p. 15p. At rated current?

Description : What are the errors of the following CT’ s 5p. 10p. 15p. At rated current?

Last Answer : 5p - 1 % Ratio error ± 60 min phase error 10p - 3 % Ratio error ± 60 min phase error 15p - 5 % Ratio error ± 60 min phase error

What are the specifications of CT?

Description : What are the specifications of CT?

Last Answer : Protection CT - Error. Alf. KpV. Metering CT - Error. Burden. Differential CT - Class PS. Core balance or E/F CT - 5-p type. Primary current - Rating of CT - 1. 15 ( full load current ) Short time rating - 1 sec.

Why CT should not be open circuited?

Description : Why CT should not be open circuited?

Last Answer : Very high voltage will be induced in secondary due to less back emf resulting in the failure of the insulation.

How can you de-saturate the CT?

Description : How can you de-saturate the CT?

Last Answer : Pass ac current through the primary and vary the current from zero to maximum with secondary in shorted condition. Pass dc current in the secondary and vary it from zero to maximum.

When will you say that the CT is saturated?

Description : When will you say that the CT is saturated?

Last Answer : When checking the CT with the secondary injection method a 10% increases in the voltage causes a 50% increase in the current the CT is said to be saturated.

Show the CT characteristics.

Description : Show the CT characteristics.

Last Answer : CT characteristics :

How to reduce the CT error?

Description : How to reduce the CT error?

Last Answer : Error reduces if load increases.

Explain with simple diagram the core balance CT.

Description : Explain with simple diagram the core balance CT.

Last Answer : In core balance CT all the three phases go through the core and the resultant magnetic flux is zero. Because the flux of three phases cancel each other. So the secondary output of CT is zero and ... energised to trip the circuit. Saturation is no problem because the core size is very big.

Explain the procedure for finding out the polarity and ratio test in a CT with circuit diagram.

Description : Explain the procedure for finding out the polarity and ratio test in a CT with circuit diagram.

Last Answer : Polarity test: Connect the circuit as shown in figure with a battery, switch and AVOmeter. Now momentarily close the switch S and see the deflection in the AVOmeter. If it is in the direction as shown in the ... A2. Then see whether it confirms to reading of nameplate. Ratio = A1/A2.

Define knee point voltage of a CT.

Description : Define knee point voltage of a CT.

Last Answer : When the primary of a CT is open circuited and supply (variable) of system frequency is given to secondary, then a 10% increase in voltage constitutes 50% increase in current. That voltage is the knee point ... Above kpv the ratio of transformer will not be applicable. kpv = RCT + RLEADS + RRELAY

Where core balance CT is used?

Description : Where core balance CT is used?

Last Answer : Core balance CT is used in earth fault protection.

Draw a neat sketch and explain the use of CT and PT for measurement of power in a single-phase circuit?

Description : Draw a neat sketch and explain the use of CT and PT for measurement of power in a single-phase circuit?

Last Answer : If wattmeter of proper range is not available or if voltage and current ranges are high we can usr CT and PT of suitable ratio. Connect the CT and PT as shown in figure. The reading of wattmeter can be multiplied by the ratio to get the actual power.

The boundary of the protective zone is determined by the (A) Location of CT (B) sensitivity of relay used (C) Location of PT (D) None of these

Description : The boundary of the protective zone is determined by the (A) Location of CT (B) sensitivity of relay used (C) Location of PT (D) None of these

Last Answer : Ans: B The boundary of the protective zone is determined by the sensitivity of relay used. If the relay is more sensitive, the protective zone will be increased.

If the anticipated revenue increase for acquiring a bid is $500,000 and the overhead is $40,000 and the company overhead is $75,000 and the minimum pretax must be 10% on the bid, using the overhead percentage, the bid price is equal to how much?

Description : If the anticipated revenue increase for acquiring a bid is $500,000 and the overhead is $40,000 and the company overhead is $75,000 and the minimum pretax must be 10% on the bid, using the overhead percentage, the bid price is equal to how much?

Last Answer : Construct an equation to perform the cost benefit analysis with revenue on one side and costs on the other side.

What happened to the anticipated popularity of Google Plus?

Description : What happened to the anticipated popularity of Google Plus?

Last Answer : answer:I know bunches of people who migrated there and very few are still active. I always said it would never catch on, because everyone and their grandmother is already on FB, and those ... people could then over-inflate their number of people in their circles to imagine the they were relevant.

Aside from your children, what wonderful things have happened in your life that you never would have anticipated when you were young?

Description : Aside from your children, what wonderful things have happened in your life that you never would have anticipated when you were young?

Last Answer : What I didn't realize as a child is how much better off you are as a child. I always thought everything would be better after I got older. I didn't realize how scary it would be when you no ... whole lot about your welfare. On the plus side, you don't have to ask for permission to buy candy.

Most anticipated videogame for rest of year?

Description : Most anticipated videogame for rest of year?

Last Answer : answer:Spore, Diablo or Starcraft. I don’t play videogames much, but these are the three names that get tossed around a lot.

What highly anticipated movie left you feeling disappointed?

Description : What highly anticipated movie left you feeling disappointed?

Last Answer : Matrix Resurrections. What the fuck was that?

Why housing market crash is anticipated ?