What are the specifications of CT?

What are the specifications of CT? 
by

1 Answer

Answer :

Protection CT - Error. Alf. KpV.

Metering CT - Error. Burden.

Differential CT - Class PS.

Core balance or E/F CT - 5-p type.

Primary current -

Rating of CT - 1. 15 ( full load current )

Short time rating - 1 sec. 
by

Related questions

What are the specifications for procurement of grounding conductor and grounding rods?

Description : What are the specifications for procurement of grounding conductor and grounding rods?

Last Answer : Grounding conductor, pad, rods etc. should have following specifications: a. Copper : 91.8 to 94.9% b. Zinc : 2.0 to 3.0% c. Tin : 0.8 to 1.5% d. Lead : 2.0 to 2.5% e. Iron : 0.5 to ... : 0.3% maximum. b. Antimony : 0.3% maximum. c. Manganese : 0.04% maximum. d. Phosphorous : 0.04% maximum. 

Before servicing the device indicated as 'A' in panels #1 and #3 of the illustration, the device labeled 'CT' must __________. EL-0003 A. have the disconnected leads taped to prevent short circuiting. B. only be connected to multimeter on the ammeter setting C. be short circuited D. have one lead grounded to discharge static electricity for the prevention of damage to electronic components

Description : Before servicing the device indicated as 'A' in panels #1 and #3 of the illustration, the device labeled 'CT' must __________. EL-0003 A. have the disconnected leads taped to prevent ... D. have one lead grounded to discharge static electricity for the prevention of damage to electronic components

Last Answer : Answer: C

Difference between Current Transformer (CT) and Potential Transformer (PT)

Description : Difference between Current Transformer (CT) and Potential Transformer (PT)

Last Answer : Current Transformers (CT) and Potential Transformers (PT) are used to measure the current and voltage in a circuit of the order of hundreds of amperes and volts respectively. A CT has large number of ... and flux density vary over a wide range whereas in PT, they vary over a limited range only

What are the errors in CT?

Description : What are the errors in CT?

Last Answer : (a) Ratio error Percentage ratio error = [(Nominal ratio – Actual ratio)/Actual ratio] x 100 The value of transformation ratio is not equal to the turns ratio. (b) Phase angle error: Phase angle =180/ [(ImCos -I1Sin )/nIs]

Where wound type CT used and where not used?

Description : Where wound type CT used and where not used?

Last Answer : Used where low CT ratio req. Not used where high short ckt. Current exists.

Give the details of switchyard 220 kV CB, Isolator, CT, CVT and lightning arrestor.

Description : Give the details of switchyard 220 kV CB, Isolator, CT, CVT and lightning arrestor.  

Last Answer : 220 kV SF6 Circuit Breaker 1. Make - ABB 2. Air pressure blocking a. Close Block - 17.3 bar. b. Open block - 16.7 bar. c. Auto reclose block - 19 bar. 3. SF6 pressure block a. Alarm - 5. ... , storage and erection. Rated voltage : 216 kV rms. Operating voltage : 184 kV rms. 

Why CT operated over load relay is using for loads of high acceleration time upto 30 seconds? How it getting back?

Description : Why CT operated over load relay is using for loads of high acceleration time upto 30 seconds? How it getting back?

Last Answer : The saturable current transformers linearly transforms the current upto twice the set current, but above this value the transformer core gets saturated and the secondary current is proportionally less. Thus ... overload. When current reduces the core gets de-saturated, as material design is such. 

How CT is connecting in ckt?

Description : How CT is connecting in ckt? 

Last Answer : If the primary of CT is delta connected load the CT will be in star connection and vice versa. This is because to have square root 3 time compensation. 

Why ICT are used?(INTERPOSING CT)

Description : Why ICT are used?(INTERPOSING CT)

Last Answer : To correct the system primary CT errors in case of high current faults out side CT zone (ICT’s primary CT is 800/1, but in fault current may go to thousands of amps. This ICT will take care of those errors. a) Matching the ratios. b) Matching the phase angle differences. 

Why core balance CT is preferred over residual connected CT’s to sense earth fault in 6.6 kV feeders?

Description : Why core balance CT is preferred over residual connected CT’s to sense earth fault in 6.6 kV feeders?

Last Answer : a) To avoid relay mal-operation due to CT saturation b) Better sensitivity is got. c) High pickup and TMS avoided in IDMT earth fault relay. 

What are the checks on CT & PT?

Description : What are the checks on CT & PT?

Last Answer : a) Polarity checks b) Insulation checks c) Ratio checks d) Knee point voltage (only for PS class CT)- magnetising characteristic test. 

Where CT secondary of 1A we are using?

Description : Where CT secondary of 1A we are using?

Last Answer : For long distance current transmission, to reduce the IR drop.  

What is the purpose of CT & PT?

Description : What is the purpose of CT & PT?

Last Answer : For transformation of current, voltage to a lower level for the purpose of Measurement, Protection and Control. 

What is the standard CT polarity?

Description : What is the standard CT polarity?

Last Answer : Primary current enters at P1 and secondary current leaves at S2.  

But is it advisable to keep the secondary of CT in open conditions? Will not induce very high voltage?

Description : But is it advisable to keep the secondary of CT in open conditions? Will not induce very high voltage?

Last Answer : If the CT has only one secondary winding, we should keep it always short cktd for safety, but if the CT has multiple secondary, then if one secondary voltage is kept limited by suitable loading, then the other secondary voltage is eventually limited proportionately. 

A CT has 2 – secondary windings. If we use only one secondary winding can we keep the unused secondary winding short circuited?

Description : A CT has 2 – secondary windings. If we use only one secondary winding can we keep the unused secondary winding short circuited?

Last Answer : No. If it is short-circuited then the ratio will not get correctly. The turns of primary winding will be shared between 2 secondary windings. So the unused secondary winding should kept open. 

What is over voltage interturn test for CT?

Description : What is over voltage interturn test for CT?

Last Answer : With secondary open, pass rated current in primary for 1 min. Then check secondary for insulation. 

What is the operating point in the Magnetising characteristic of protection CT & measuring CT?

Description : What is the operating point in the Magnetising characteristic of protection CT & measuring CT? 

Last Answer : Protection CT – Operation at ankle point only. Measuring CT – Operation from ankle to knee point 

What are the errors of the following CT’ s 5p. 10p. 15p. At rated current?

Description : What are the errors of the following CT’ s 5p. 10p. 15p. At rated current?  

Last Answer : 5p - 1 % Ratio error ± 60 min phase error 10p - 3 % Ratio error ± 60 min phase error 15p - 5 % Ratio error ± 60 min phase error 

Why CT should not be open circuited?

Description : Why CT should not be open circuited?

Last Answer : Very high voltage will be induced in secondary due to less back emf resulting in the failure of the insulation. 

How can you de-saturate the CT?

Description : How can you de-saturate the CT? 

Last Answer : Pass ac current through the primary and vary the current from zero to maximum with secondary in shorted condition. Pass dc current in the secondary and vary it from zero to maximum.

What is the problem anticipated due to CT saturation?

Description : What is the problem anticipated due to CT saturation?  

Last Answer : The CT will not be able to drive the current through the circuit causing nonoperation of relays. In some other case when the currents in the two phases are compared for relay operation the relay may operate due to unbalance. 

When will you say that the CT is saturated?

Description : When will you say that the CT is saturated?

Last Answer : When checking the CT with the secondary injection method a 10% increases in the voltage causes a 50% increase in the current the CT is said to be saturated. 

Show the CT characteristics.

Description : Show the CT characteristics.

Last Answer : CT characteristics :  

How to reduce the CT error?

Description : How to reduce the CT error? 

Last Answer : Error reduces if load increases.  

Explain with simple diagram the core balance CT.

Description : Explain with simple diagram the core balance CT.

Last Answer : In core balance CT all the three phases go through the core and the resultant magnetic flux is zero. Because the flux of three phases cancel each other. So the secondary output of CT is zero and ... energised to trip the circuit. Saturation is no problem because the core size is very big.  

Explain the procedure for finding out the polarity and ratio test in a CT with circuit diagram.

Description : Explain the procedure for finding out the polarity and ratio test in a CT with circuit diagram. 

Last Answer : Polarity test: Connect the circuit as shown in figure with a battery, switch and AVOmeter. Now momentarily close the switch S and see the deflection in the AVOmeter. If it is in the direction as shown in the ... A2. Then see whether it confirms to reading of nameplate. Ratio = A1/A2. 

Define knee point voltage of a CT.

Description : Define knee point voltage of a CT.

Last Answer : When the primary of a CT is open circuited and supply (variable) of system frequency is given to secondary, then a 10% increase in voltage constitutes 50% increase in current. That voltage is the knee point ... Above kpv the ratio of transformer will not be applicable. kpv = RCT + RLEADS + RRELAY  

Where core balance CT is used?

Description : Where core balance CT is used?

Last Answer : Core balance CT is used in earth fault protection.  

Draw a neat sketch and explain the use of CT and PT for measurement of power in a single-phase circuit?

Description : Draw a neat sketch and explain the use of CT and PT for measurement of power in a single-phase circuit?

Last Answer : If wattmeter of proper range is not available or if voltage and current ranges are high we can usr CT and PT of suitable ratio. Connect the CT and PT as shown in figure. The reading of wattmeter can be multiplied by the ratio to get the actual power.   

The boundary of the protective zone is determined by the (A) Location of CT (B) sensitivity of relay used (C) Location of PT (D) None of these

Description : The boundary of the protective zone is determined by the (A) Location of CT (B) sensitivity of relay used (C) Location of PT (D) None of these

Last Answer : Ans: B The boundary of the protective zone is determined by the sensitivity of relay used. If the relay is more sensitive, the protective zone will be increased.

Where can I find information about GMail html specifications?

Description : Where can I find information about GMail html specifications?

Last Answer : Need Answer

In editing HD video using a laptop, what are the minimum specifications needed?

Description : In editing HD video using a laptop, what are the minimum specifications needed?

Last Answer : answer:What is your graphics card? You can do it on that, but even on a 2.4 GHZ dual core the video will take a long time to render and decode when you’re done. Most video editing rigs are a little beefier than that.

Specifications for buildng a chimney?

Description : Specifications for buildng a chimney?

Last Answer : Oh my. This is a sticky one with so many variables. Here's the easy part. Typically code says it should be 2 feet above the peak. but peole try to go 3 feet to draw better and reduce dirt on the ... code there? I hate to say this but I recommend you google it . There are plenty of good examples.

If you could order/design the perfect, custom, utilitarian/functional household or workplace robot what would it's specifications be?

Description : If you could order/design the perfect, custom, utilitarian/functional household or workplace robot what would it's specifications be?

Last Answer : answer:It must have a fresh pot of coffee ready for me, cup in my hand once I wake up. Weed my garden. Wash my clothes. I don’t ask fo much.

Is there a camcorder that meets these specifications?

Description : Is there a camcorder that meets these specifications?

Last Answer : Sorry buddy, but an HD cam for under $250 doesn’t currently exist. You need to save up some more otherwise you have to go non-HD. Also a videocamera for machinima? Why not get a cheap capture card. It looks a lot better too.

Can you help me with computer specifications, please?

Description : Can you help me with computer specifications, please?

Last Answer : answer:Go w/ the Fujitsu. It’s at least a brand I’ve heard of, and in general, a non-integrated graphics card will perform better. The advent has a tad faster processor, but don’t think it’s worth the price.

Write the HTML code to generate the following web page with the given below specifications: -Technology

Description : Write the HTML code to generate the following web page with the given below specifications: -Technology

Last Answer : Income Tax Slabs 2017-18INCOME TAX SLABS 2017-18S.No.Income RangeTax%10-250000NIL2250001-50000010%3500001-100000020%4>100000030%Next Page

Shambhavi has to design two Web pages with following specifications : -Technology

Description : Shambhavi has to design two Web pages with following specifications : -Technology

Last Answer : (i) Tags →, ,Attribute → type(ii) Tags →,Attribute→ bgcolour

Computers at the cheapest prices and the highest specifications?

Description : Computers at the cheapest prices and the highest specifications?

Last Answer : Need Answer

what are the specifications for a model C allis chalmers tractor

Description : what are the specifications for a model C allis chalmers tractor

Last Answer : See here > http://www.tractordata.com/farm-tractors/000/0/0/4-allis-chalmers-c.html

How are design specifications used in the construction of a structure Give examples in your answer.?

Description : How are design specifications used in the construction of a structure Give examples in your answer.?

Last Answer : What is the answer ?

What are the electrical specifications needed to operate the tanning bed?

Description : What are the electrical specifications needed to operate the tanning bed?

Last Answer : Most tanning beds require 220 volts. Most homes are not wired to supply this kind of power. It is best to call a certified electrician to install a dedicated circuit to avoid the risk of electrical overload.

What are this computer's technical specifications What type of optical drive does it have How much and what type of system memory What type of HDD What is the size of its monitor?

Description : What are this computer's technical specifications What type of optical drive does it have How much and what type of system memory What type of HDD What is the size of its monitor?

Last Answer : According to the manufacturer, the Toshiba Portege R500-S5004 has an Intel Core Duo U7600 processor, 2GB of DDR2 SDRAM, a solid state 64Gb hard drive, a built-in 802.11n wireless card, a DVD SuperMulti read/write drive, and a 12.1" widescreen monitor.

what are the specifications for rural mailbox settings ?

Description : what are the specifications for rural mailbox settings ?

Last Answer : Take a look at this USPS webpage which has information on mailbox restrictions: http://pe.usps.com/text/dmm300/508.htm

What are the specifications for air hockey table motors and where can you find replacement parts?

Description : What are the specifications for air hockey table motors and where can you find replacement parts?

Last Answer : You should try looking at your air hockey table manual. They usually have the specifications and where you could get their replacement parts.

What hardware specifications constitute a 'gaming computer'?

Description : What hardware specifications constitute a 'gaming computer'?

Last Answer : You will need to make sure that there is a really good graphics card on your computer, and also you will need a really large amount of space for your computer to run games up to speed.

What are the benefits of an LCD television versus one with led specifications?

Description : What are the benefits of an LCD television versus one with led specifications?

Last Answer : LED televisions have better color contrast than LCD televisions. LCD televisions have better viewing angles than LED televisions do, meaning that viewing to television from the side is more comfortable with the LCD televisions than with the LED televisions.

What are the specifications to obtain a grant for sports medicine?

Description : What are the specifications to obtain a grant for sports medicine?

Last Answer : Yes, there are degrees in sports medicine. You can also find certificate programs for them if you do not wish to obtain a college degree. You will have to search for schools that offer that program and apply to them.