Description : In sunk key no slips occurs A. True B. False
Last Answer : A. True
Description : Saddle key is more suitable than sunk key for heavy duty applications. a) True b) False
Last Answer : b) False
Description : The main advantage of sunk key is that it is a _____ drive. a) Positive b) Negative c) Neutral d) None of the listed
Last Answer : a) Positive
Description : A sunk key fits in the keyway of the _____ only. a) Hub b) Sleeve c) Both hub and sleeve d) Neither hub nor sleeve
Last Answer : a) Hub
Description : Sunk key is a .............. drive. A. Positive B. Negative C. Neutral D. None
Last Answer : A. Positive
Description : Sunk key fits in the keyway of the .......... only. A. Sleeve B. Hub C. Both sleeve and hub D. neither sleeve and hub
Last Answer : B. Hub
Description : In case of sunk key, (A) The keyway is cut in the shaft only (B) The keyway is cut in the hub only (C) The keyway is cut in both the shaft and the hub (D) None of the above
Last Answer : (C) The keyway is cut in both the shaft and the hub
Description : The key in the form of semi-circular disk of uniform thickness is called, (A) Sunk key (B) Feather key (C) Woodruff key (D) Kennedy key
Last Answer : (C) Woodruff key
Description : The type of key used when the gear is required to slide on the shaft is (A) Sunk key (B) Feather key (C) Woodruff key (D) Kennedy key
Last Answer : (B) Feather key
Description : Feather key can be used to prevent axial motion between two elements. a) True b) False
Description : Hollow saddle key is superior to flat saddle key as far as power transmitting capability is concerned. a) True b) False
Description : Saddle key is transmit power or torque through friction resistant only A. True B. False
Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False
Description : Sliding contact bearings, also called plain bearings have no problem of wear. a) True b) False
Description : Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section. a) True b) False
Description : Keyed joints never lead to stress concentration on shafts. a) True b) False
Description : The operation of flywheel is continuous. a) True b) False
Last Answer : a) True
Description : Flywheel and governor can be interchanged. a) True b) False
Description : Flywheels are used in punching and shear operation. a) True b) False
Description : Is use of a flywheel recommended when a large motor is required only for a small instant of time? a) True b) False
Description : The dynamic load-carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. (a) True (b) False
Last Answer : (b) False
Description : For the majority of bearings, actual life is considerably greater than rated life. (a) True (b) False
Last Answer : (a) True
Description : The life of an individual ball bearing is the time period for which it works without any signs of failures. (a) True (b) False
Description : Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False
Description : Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False
Description : A cylinder roller creates lesser noise than a deep groove ball bearing. (a) True (b) False
Description : Angular contact bearing can take thrust as well as radial loads. (a) True (b) False
Description : Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False
Description : Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is ... (c) A is true but R is false (d) A is false but R is true
Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A
Description : Assertion (A): In hydrodynamic journal bearings, the rotating journal is held in floating condition by the hydrodynamic pressure developed in the lubricant. Reason (R): Lubricant flows in a converging-diverging channel. [IES-1994] ... A (c) A is true but R is false (d) A is false but R is true
Last Answer : (a) Both A and R are individually true and R is the correct explanation of A
Description : Assertion (A): Oil as a cutting fluid result in a lower coefficient of friction. Reason (R): Oil forms a thin liquid film between the tool face and chip, and it provides 'hydrodynamic lubrication'. [IES- 2000] (a ... explanation of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (c) A is true but R is false
Description : Assertion (A): In anti-friction bearings, the frictional resistance is very low as the shaft held by it remains in floating condition by the hydrodynamic pressure developed by the lubricant. [IES-2006] Reason (R): In hydrodynamic ... of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (d) A is false but R is true
Description : Assertion (A): In equilibrium position, the journal inside a journal bearing remains floating on the oil film. [IES-1995] Reason (R): In a journal bearing, the load on the bearing is perpendicular to the axis of the ... explanation of A (c) A is true but R is false (d) A is false but R is true
Description : Assertion (A): In steady rotating condition the journal inside a hydrodynamic journal bearing remains floating on the oil film. [IES-2008] Reason (R): The hydrodynamic pressure developed in steady rotating conditions in journal ... A (c) A is true but R is false (d) A is false but R is true
Last Answer : (a) Both A and R are true and R is the correct explanation of A
Description : Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False
Description : A single transverse weld is preferred over double transverse fillet weld. a) True b) False
Description : If fluid film pressure is high and surface rigidity is low than mode of lubrication is called as elastohydrodynamic lubrication. a) True b) False
Description : Hydrostatic and hydrodynamic lubrication are the same thing. a) True b) False
Description : Hydrodynamic bearing is a self-acting bearing. a) True b) False
Description : Needles bearing consist of rollers of small diameter and very small length. a) True b) False
Description : The dynamic load carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. a) True b) False
Description : For majority of bearings, actual life is considerably greater than rated life. a) True b) False
Description : The life of an individual ball bearing is the time period for which it works without any signs of failures. a) True b) False
Description : Stribeck equation gives dynamic load capacity of the bearing. a) True b) False