Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft. a) True b) False
Last Answer : a) True
Description : Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned
Last Answer : d) All of the mentioned
Description : The static load carrying capacity of fine threads is greater than that of coarse threads. a) True b) False
Last Answer : b) False
Description : Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False
Last Answer : (b) False
Description : Cylindrical load bearing has lower load capacity as compared to deep groove ball bearing. a) True b) False
Description : The permanent mode of deformation of a material known as _____________ a) Elasticity b) Plasticity c) Slip deformation d) Twinning deformation
Last Answer : b) Plasticity
Description : Which of the following facts are true for resilience? a) Ability of material to absorb energy when deformed elastically b) Ability to retain deformation under the application of load or after removal ... c) Ability of material to absorb energy when deformed plastically d) None of the mentioned
Last Answer : a) Ability of material to absorb energy when deformed elastically
Description : There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance. a) True b) False
Description : The dynamic load-carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. (a) True (b) False
Description : Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False
Description : The dynamic load carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. a) True b) False
Description : Stribeck equation gives dynamic load capacity of the bearing. a) True b) False
Description : Cotter joint is a permanent fastening. a) true b) false
Last Answer : b) false
Description : The life of an individual ball bearing is the time period for which it works without any signs of failures. (a) True (b) False
Description : A cylinder roller creates lesser noise than a deep groove ball bearing. (a) True (b) False
Description : The life of an individual ball bearing is the time period for which it works without any signs of failures. a) True b) False
Description : Cylinder roller creates lesser noise than deep groove ball bearing. a) True b) False
Description : Balls and the races of the deep groove ball may roll freely without any sliding. a) True b) False
Description : Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False
Description : Needles bearing consist of rollers of small diameter and very small length. a) True b) False
Description : The spring index is the ratio of wire diameter to mean coil diameter. a) True b) False
Description : Nominal diameter of the screw thread is the same as core diameter. a) True b) False
Description : The static load is defined as the load acting on the bearing when the shaft is _____. (a) stationary (b) rotating at rpm
Last Answer : (a) stationary
Description : Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm
Last Answer : a) Stationary
Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three
Last Answer : (D) All the three
Description : The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load
Last Answer : (d) completely reversed load
Description : In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load
Last Answer : a) Ductile material under static load
Description : The capacity of welded structures to damp vibrations is quite good. a) True b) False
Description : What Properties Are Needed To Be Considered For Application Calling For Following Requirements? I) Rigidity. Ii) Strength Of No Plastic Deformation Under Static Load. Iii) Strength To Withstand Overload Without Fracture.
Last Answer : i) Reliability – elastic modulus and yield strength. ii) Strength (for no plastic deformation under static loading) – yield point. iii) Strength (overload) – Toughness and impact resistance. iv) Wear resistance – Hardness. v) Reliability and safety – Endurance limit and yield.
Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact
Last Answer : (C) There should be elastic deformation of the parts in contact
Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact
Last Answer : (B) There should be external source like pump to supply lubricant under pressure
Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact
Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space
Description : Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed
Last Answer : d) All of the listed
Description : Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture
Last Answer : c) Creep
Description : The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength
Last Answer : b) Yield strength
Description : The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed
Last Answer : d) None of the listed
Description : The shock absorbing capacity of bolt can be increased by making the shank diameter ________ the root diameter. a) Lesser than b) Equal to c) Greater than d) No effect
Last Answer : b) Equal to
Description : The shock absorbing capacity of a bolt can be increased by (A) Increasing shank diameter (B) Making shank diameter equal to core diameter of threads (C) Using castle nut in place of ordinary hexagonal nut (D) Using a washer
Last Answer : (B) Making shank diameter equal to core diameter of threads
Description : The shock absorbing capacity of a bolt can be increased by (A) Increasing stress in shank (B) Increasing stress in core diameter of threads (C) Decreasing stress in shank (D) Decreasing stress in core diameter of threads
Last Answer : (A) Increasing stress in shank
Description : Assertion (A): In equilibrium position, the journal inside a journal bearing remains floating on the oil film. [IES-1995] Reason (R): In a journal bearing, the load on the bearing is perpendicular to the axis of the ... explanation of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A
Description : Assertion (A): In steady rotating condition the journal inside a hydrodynamic journal bearing remains floating on the oil film. [IES-2008] Reason (R): The hydrodynamic pressure developed in steady rotating conditions in journal ... A (c) A is true but R is false (d) A is false but R is true
Last Answer : (a) Both A and R are true and R is the correct explanation of A
Description : A radial bearing supports the load that acts along the axis of the shaft. a) True b) False
Description : Certain types of radial bearings can also take thrust load. a) True b) False
Description : The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN
Last Answer : (b) 37.29 kN
Description : Which one of the following bearing is intended for a very heavy radial load? (a) Ball bearing (b) Self-aligning roller bearing (c) Roller bearing (d) Thrust bearing
Last Answer : (b) Self-aligning roller bearing
Description : Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing
Last Answer : (c) Thrust ball bearing
Description : Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing
Last Answer : (c) Cylindrical (straight) roller bearing
Description : Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed
Last Answer : (d) combined thrust and radial loads at high speed
Description : Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For ... C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4
Last Answer : (c) 2 4 3 1