Description : A sunk key fits in the keyway of the _____ only. a) Hub b) Sleeve c) Both hub and sleeve d) Neither hub nor sleeve
Last Answer : a) Hub
Description : In case of sunk key, (A) The keyway is cut in the shaft only (B) The keyway is cut in the hub only (C) The keyway is cut in both the shaft and the hub (D) None of the above
Last Answer : (C) The keyway is cut in both the shaft and the hub
Description : The key, which fits in the keyway of hub, only is called, (A) Saddle key (B) Feather key (C) Woodruff key (D) Kennedy key
Last Answer : (A) Saddle key
Description : The main advantage of sunk key is that it is a _____ drive. a) Positive b) Negative c) Neutral d) None of the listed
Last Answer : a) Positive
Description : Saddle key is more suitable than sunk key for heavy duty applications. a) True b) False
Last Answer : b) False
Description : In sunk key no slips occurs A. True B. False
Last Answer : A. True
Description : Sunk key is a .............. drive. A. Positive B. Negative C. Neutral D. None
Last Answer : A. Positive
Description : The key in the form of semi-circular disk of uniform thickness is called, (A) Sunk key (B) Feather key (C) Woodruff key (D) Kennedy key
Last Answer : (C) Woodruff key
Description : The type of key used when the gear is required to slide on the shaft is (A) Sunk key (B) Feather key (C) Woodruff key (D) Kennedy key
Last Answer : (B) Feather key
Description : The keyway, (A) Reduces strength of shaft (B) Reduces rigidity of shaft (C) Increases stress concentration (D) All of above
Last Answer : (D) All of above
Description : Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed
Last Answer : b) Radial
Description : Antifriction bearings are (a) sleeve bearings (b) hydrodynamic bearings (c) thin lubricated bearings (d) none of the mentioned
Last Answer : (d) none of the mentioned
Description : Antifriction bearings are A. Sleeve bearings B. Hydrodynamic bearings C. Thin lubricated bearings D. None of the above
Last Answer : D. None of the above
Description : A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.
Last Answer : (a) butt weld
Description : For finding out the bending moment for the arm (spoke) of flywheel the arm is assumed as 1. a cantilever beam fixed at the rim and subjected to tangential force at the hub 2. a simply ... tangential force at the rim 4. a fixed beam fixed at hub and rim and carrying uniformly distributed load
Last Answer : 3. a cantilever hub fixed at the rim and subjected to tangential force at the rim
Description : The hub diameter of the flywheel is taken as 1. 2.5(shaft diameter) 2. 1.5(shaft diameter) 3. 4(shaft diameter) 4. 2(shaft diameter)
Last Answer : 4. 2(shaft diameter)
Description : The hub diameter of the flywheel is taken as, (A) 2.5 (shaft diameter) (B) 1.5 (shaft diameter) (C) 4 (shaft diameter) (D) 2 (shaft diameter)
Last Answer : (D) 2 (shaft diameter)
Description : For finding out the bending moment for the arm (spoke) of flywheel, the arm is assumed as, (A) A cantilever beam fixed at the rim and subjected to tangential force at the hub (B) A simply ... tangential force at the rim (D) A fixed beam fixed at hub and rim and carrying uniformly distributed load
Last Answer : (C) A cantilever beam fixed at the hub and subjected to tangential force at the rim
Description : Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm. a) 6.77N/mm2 b) 10.24N/mm2 c) 4.84N/mm2 d) 4.22N/mm2
Last Answer : c) 4.84N/mm2
Description : The hub is treated as a solid shaft while calculating torsional shear stress in the hub. a) True b) False
Description : Splines are used if, (A) The power to be transmitted is high (B) The torque to be transmitted is high (C) The speed is high (D) There is relative motion between shaft and hub
Last Answer : (D) There is relative motion between shaft and hub
Description : Taper is given on key is generally.......... A. Top side only B. Bottom side only C. On both side D. Any side
Last Answer : A. Top side only
Description : Which of the following doesn’t waste energy? a) Flywheel b) Governor c) Both flywheel and governor d) Neither flywheel nor governor
Last Answer : a) Flywheel
Description : Saddle key is transmit power or torque through friction resistant only A. True B. False
Description : Which among the following is the condition to avoid separation of connected members? a. Force acting on the connected members should be negative b. Force acting on the connected members should be ... acting on the connected members should be neither positive nor negative d. None of the above
Last Answer : a. Force acting on the connected members should be negative
Description : Feather key can be used to prevent axial motion between two elements. a) True b) False
Description : Allen key is used to tighten (A) Cap screw with hexagonal head (B) Cap screw with fillister head (C) Cap screw with hexagonal socket head (D) Cap screw with flat head
Last Answer : (C) Cap screw with hexagonal socket head
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed
Last Answer : b) 51.6N/mm2
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed
Last Answer : b) 25.8N/mm2
Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm
Last Answer : d) 53mm
Description : Hollow saddle key is superior to flat saddle key as far as power transmitting capability is concerned. a) True b) False
Description : Taper on rectangular sink key is ....... A. 1 in 16 B. 1 in 48 C. 1 in 100 D. 1 in 120
Last Answer : C. 1 in 100
Description : The compressive stress induced in a square key is, (A) Equal to shear stress (B) Four times of shear stress (C) Twice of shear stress (D) Half of shear stress
Last Answer : (C) Twice of shear stress
Description : While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component
Last Answer : (C) Key is the weakest component
Description : The standard length for square or flat key in terms of shaft diameter (D) is, (A) d (B) 2d (C) 1.5d (D) 2.5d
Last Answer : (C) 1.5d
Description : Kennedy key is used in (A) Light duty applications (B) Heavy duty applications (C) High speed applications (D) Precision equipments
Last Answer : (B) Heavy duty applications
Description : The distribution of the forces along the length of key fitted in a shaft (A) Varies linearly (B) Is uniform throughout (C) Varies exponentially, being more near the torque-input end (D) Varies exponentially, being less near the torque-input end
Last Answer : (C) Varies exponentially, being more near the torque-input end
Description : Write the suitable cutter for carrying following operations on milling machine (i) Gear Tooth (ii) Parting off (iii) Keyway (iv) V-grooves (v) Rounding of corner (vi) Cutting of narrow slot and groove
Last Answer : (i) Gear Tooth : Form milling cutter, Cylindrical type or End mill type, Gear cutter. (ii) Parting off: Slitting Cutter (iii) Keyway : Staggered teeth side milling cutter, End mill cutter, key ... milling cutter. Selection of a cutter depends upon type and size of slot or groove to be produced.
Description : Explain keyway milling process with standard milling cutters.
Last Answer : Keyway Milling Operation: This milling process produce keyway slot. The cutter use if thin size. This operation suited for long keyways. The position of the cutter is shown in figure. Standard ... and then the cut is taken. Woodruff key is produced by using a woodruff key slot cutter.
Description : _________is just aconnector. A) An activehub B) A passive hub C) either (a)or (b) D) neither (a)nor (b)
Last Answer : A passive hub
Description : Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity
Last Answer : (c) both radial and axial loads and the ratio of these being greater than unity