Description : The main advantage of sunk key is that it is a _____ drive. a) Positive b) Negative c) Neutral d) None of the listed
Last Answer : a) Positive
Description : Sunk key is a .............. drive. A. Positive B. Negative C. Neutral D. None
Last Answer : A. Positive
Description : A sunk key fits in the keyway of the _____ only. a) Hub b) Sleeve c) Both hub and sleeve d) Neither hub nor sleeve
Last Answer : a) Hub
Description : Saddle key is more suitable than sunk key for heavy duty applications. a) True b) False
Last Answer : b) False
Description : In sunk key no slips occurs A. True B. False
Last Answer : A. True
Description : Sunk key fits in the keyway of the .......... only. A. Sleeve B. Hub C. Both sleeve and hub D. neither sleeve and hub
Last Answer : B. Hub
Description : In case of sunk key, (A) The keyway is cut in the shaft only (B) The keyway is cut in the hub only (C) The keyway is cut in both the shaft and the hub (D) None of the above
Last Answer : (C) The keyway is cut in both the shaft and the hub
Description : The key in the form of semi-circular disk of uniform thickness is called, (A) Sunk key (B) Feather key (C) Woodruff key (D) Kennedy key
Last Answer : (C) Woodruff key
Description : The type of key used when the gear is required to slide on the shaft is (A) Sunk key (B) Feather key (C) Woodruff key (D) Kennedy key
Last Answer : (B) Feather key
Description : Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed
Last Answer : b) Radial
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed
Last Answer : b) 51.6N/mm2
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed
Last Answer : b) 25.8N/mm2
Description : Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm
Last Answer : a) Stationary
Description : Which among the following is the condition to avoid separation of connected members? a. Force acting on the connected members should be negative b. Force acting on the connected members should be ... acting on the connected members should be neither positive nor negative d. None of the above
Last Answer : a. Force acting on the connected members should be negative
Description : In Mohr's circle method, compressive direct stress is represented on ____ a. positive x-axis b. positive y-axis c. negative x-axis d. negative y-axis
Last Answer : c. negative x-axis
Description : What is the main advantage of hydrodynamic bearing over roller bearing? (a) Easy to assemble [IES-2005] (b) Relatively low price (c) Superior load carrying capacity at higher speeds (d) Less frictional resistance
Last Answer : (c) Superior load carrying capacity at higher speeds
Description : Which of the following are functions of flywheel? a) Store and release energy during work cycle b) Reduce power capacity of the electric motor c) Reduce amplitude of speed fluctuations d) All of the listed
Last Answer : d) All of the listed
Description : An antifriction bearing consists of (a) rolling elements (b) races (c) cages (d) all of the listed
Last Answer : (d) all of the listed
Description : Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed
Last Answer : (d) All of the listed
Description : The listed life of a rolling bearing, in a catalog is the, (a) minimum expected life (b) maximum expected life (c) average life (d) none of the mentioned
Last Answer : (a) minimum expected life
Description : Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed
Last Answer : b) Thrust load
Description : In the expression of dynamic load capacity P=XVF(r) + YF(a), V stands for ? a) Race rotation factor b) Radial factor c) Thrust factor d) None of the listed
Last Answer : a) Race rotation factor
Description : Which of the following is expression for stribeck equation?(Number of balls=z)? a) C=kd2z/5 b) C=kd2z/15 c) C=kd2z/10 d) None of the listed
Last Answer : a) C=kd2z/5
Description : Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed
Description : Which of the following cannot take radial load? a) Cylindrical Roller bearing b) Taper roller bearing c) Thrust ball bearing d) None of the listed
Last Answer : c) Thrust ball bearing
Description : Which of the following are functions of bearings? a) Ensure free rotation of shaft with minimum friction b) Holding shaft in a correct position c) Transmit the force of the shaft to the frame d) All of the listed
Description : The strain energy stored in a spiral spring is given by? a) 12M2L/Ebtɜ b) 6M2L/Ebtɜ c) 8M2L/Ebtɜ d) None of the listed
Last Answer : b) 6M2L/Ebtɜ
Description : Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed
Last Answer : b) Due to tensile
Description : When two Belleville sprigs are arranged in series, half deflection is obtained for same force. a) One fourth deflection b) Double deflection c) Four time deflection d) None of the listed
Last Answer : b) Double deflection
Description : Angle of rotation o arbour with respect to drum is given by? a) None of the listed b) 12ML/Ebtɜ c) 8 ML/Ebtɜ d) 16ML/Ebtɜ
Last Answer : b) 12ML/Ebtɜ
Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping
Last Answer : a) Fatigue Failure
Description : Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed
Last Answer : b) It is measured in uncompressed state
Description : If number of coils are 8 and wire diameter of spring 3mm, then solid length is given by? a) None of the listed b) 27mm c) 24mm d) 21mm
Last Answer : c) 24mm
Description : The longest leaf in a leaf spring is called centre leaf. a) It is called middle leaf b) It is called master leaf c) Yes d) None of the listed
Last Answer : b) It is called master leaf
Description : The helix angle is very small about 20. The spring is open coiled spring. a) Yes b) It is closed coiled spring c) That small angle isn’t possible d) None of the listed
Last Answer : b) It is closed coiled spring
Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed
Last Answer : a) M/2πtr2
Description : While calculating bending stress in the following welded joints which of the welds moment of inertia can be neglected? a) 1 b) None of the listed c) Both 1 & 3 d) Both 2 & 4
Last Answer : b) None of the listed
Description : Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm. a) 230/t b) 360/t c) 200/t d) None of the listed
Last Answer : b) 360/t
Description : Calculate the moment of inertia about the axis parallel to welds and shift it to CG by considering thickness of welds t. a) tɜ+2000t b) None of the listed c) 250000 t d) 125000 t
Last Answer : c) 250000 t
Description : A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by a) My/I b) 2My/I c) My/2I d) None of the listed
Last Answer : a) My/I
Description : If length of weld is l and leg h, then area of throat can be given by a) 0.707 hl b) 1.414hl c) hl d) None of the listed
Last Answer : a) 0.707 hl
Description : Relation between throat and leg for a parallel fillet weld is a) t =h Cos (45’) b) h =t Cos (45’) c) h= t d) None of the listed
Last Answer : a) t =h Cos (45’)
Description : The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed
Last Answer : a) Leg
Description : Filler material is used in electric resistance welding. a) Yes b) No filler material used c) Depends on the type of welding d) None of the listed
Last Answer : b) No filler material used
Description : Forge welding involves heating of parts to elastic stage and joint is prepared by impact force. a) Yes b) No, it is done up to plastic stage c) Heating is done up to boiling point d) None of the listed
Last Answer : b) No, it is done up to plastic stage