Description : Surge is a desirable effect in the sprigs. a) True b) False
Last Answer : b) False
Description : In concentric springs, vibrations called surge are amplified. a) True b) False
Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping
Last Answer : a) Fatigue Failure
Description : Belleville spring can be used in clutch application. a) True b) False
Last Answer : a) True
Description : The strip of spiral spring is never subjected to pure bending moment. a) True b) False
Description : For two springs connected in parallel, net force is equal to the sum of force in each spring. a) True b) False
Description : For two spring connected in series, the force acting on each spring is same and equal to half of the external force. a) True b) False
Description : A spring of stiffness constant k is cut in two equal parts. The stiffness constant of new spring will be k/2. a) True b) False
Description : Spring having square ends has 1 inactive coil. a) True b) False
Description : A spring with index=15 is prone to buckling. a) True b) False
Description : The spring index is the ratio of wire diameter to mean coil diameter. a) True b) False
Description : The helical spring ad wire of helical torsion spring, both are subjected to torsional shear stresses. a) True b) False
Description : Concentric springs are used, (A) To achieve greater load carrying capacity with given space (B) To achieve fail-safe system (C) To eliminate surge (D) Any of the above objectives
Last Answer : (D) Any of the above objectives
Description : Martin’s factor compensates for curvature effect in springs. a) True b) False
Description : Keyed joints never lead to stress concentration on shafts. a) True b) False
Description : Feather key can be used to prevent axial motion between two elements. a) True b) False
Description : The operation of flywheel is continuous. a) True b) False
Description : Flywheel and governor can be interchanged. a) True b) False
Description : Flywheels are used in punching and shear operation. a) True b) False
Description : Is use of a flywheel recommended when a large motor is required only for a small instant of time? a) True b) False
Description : The dynamic load-carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. (a) True (b) False
Last Answer : (b) False
Description : For the majority of bearings, actual life is considerably greater than rated life. (a) True (b) False
Last Answer : (a) True
Description : The life of an individual ball bearing is the time period for which it works without any signs of failures. (a) True (b) False
Description : Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False
Description : Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False
Description : A cylinder roller creates lesser noise than a deep groove ball bearing. (a) True (b) False
Description : Angular contact bearing can take thrust as well as radial loads. (a) True (b) False
Description : Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False
Description : Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is ... (c) A is true but R is false (d) A is false but R is true
Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A
Description : Assertion (A): In hydrodynamic journal bearings, the rotating journal is held in floating condition by the hydrodynamic pressure developed in the lubricant. Reason (R): Lubricant flows in a converging-diverging channel. [IES-1994] ... A (c) A is true but R is false (d) A is false but R is true
Last Answer : (a) Both A and R are individually true and R is the correct explanation of A
Description : Assertion (A): Oil as a cutting fluid result in a lower coefficient of friction. Reason (R): Oil forms a thin liquid film between the tool face and chip, and it provides 'hydrodynamic lubrication'. [IES- 2000] (a ... explanation of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (c) A is true but R is false
Description : Assertion (A): In anti-friction bearings, the frictional resistance is very low as the shaft held by it remains in floating condition by the hydrodynamic pressure developed by the lubricant. [IES-2006] Reason (R): In hydrodynamic ... of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (d) A is false but R is true
Description : Assertion (A): In equilibrium position, the journal inside a journal bearing remains floating on the oil film. [IES-1995] Reason (R): In a journal bearing, the load on the bearing is perpendicular to the axis of the ... explanation of A (c) A is true but R is false (d) A is false but R is true
Description : Assertion (A): In steady rotating condition the journal inside a hydrodynamic journal bearing remains floating on the oil film. [IES-2008] Reason (R): The hydrodynamic pressure developed in steady rotating conditions in journal ... A (c) A is true but R is false (d) A is false but R is true
Last Answer : (a) Both A and R are true and R is the correct explanation of A
Description : Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False
Description : A single transverse weld is preferred over double transverse fillet weld. a) True b) False
Description : If fluid film pressure is high and surface rigidity is low than mode of lubrication is called as elastohydrodynamic lubrication. a) True b) False
Description : Hydrostatic and hydrodynamic lubrication are the same thing. a) True b) False
Description : Hydrodynamic bearing is a self-acting bearing. a) True b) False
Description : Needles bearing consist of rollers of small diameter and very small length. a) True b) False
Description : The dynamic load carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. a) True b) False
Description : For majority of bearings, actual life is considerably greater than rated life. a) True b) False
Description : The life of an individual ball bearing is the time period for which it works without any signs of failures. a) True b) False
Description : Stribeck equation gives dynamic load capacity of the bearing. a) True b) False
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft. a) True b) False
Description : Cylinder roller creates lesser noise than deep groove ball bearing. a) True b) False
Description : Angular contact bearing can take thrust as well as radial loads. a) True b) False
Description : Cylindrical load bearing has lower load capacity as compared to deep groove ball bearing. a) True b) False