Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False
Last Answer : (a) True
Description : Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned
Last Answer : d) All of the mentioned
Description : The static load carrying capacity of fine threads is greater than that of coarse threads. a) True b) False
Last Answer : b) False
Description : Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False
Last Answer : (b) False
Description : Cylindrical load bearing has lower load capacity as compared to deep groove ball bearing. a) True b) False
Description : The static load is defined as the load acting on the bearing when the shaft is _____. (a) stationary (b) rotating at rpm
Last Answer : (a) stationary
Description : Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm
Last Answer : a) Stationary
Description : A radial bearing supports the load that acts along the axis of the shaft. a) True b) False
Description : The permanent mode of deformation of a material known as _____________ a) Elasticity b) Plasticity c) Slip deformation d) Twinning deformation
Last Answer : b) Plasticity
Description : The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN
Last Answer : (b) 37.29 kN
Description : The hub diameter of the flywheel is taken as 1. 2.5(shaft diameter) 2. 1.5(shaft diameter) 3. 4(shaft diameter) 4. 2(shaft diameter)
Last Answer : 4. 2(shaft diameter)
Description : The hub diameter of the flywheel is taken as, (A) 2.5 (shaft diameter) (B) 1.5 (shaft diameter) (C) 4 (shaft diameter) (D) 2 (shaft diameter)
Last Answer : (D) 2 (shaft diameter)
Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm
Last Answer : d) 53mm
Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d
Last Answer : (B) 3 d
Description : Which of the following facts are true for resilience? a) Ability of material to absorb energy when deformed elastically b) Ability to retain deformation under the application of load or after removal ... c) Ability of material to absorb energy when deformed plastically d) None of the mentioned
Last Answer : a) Ability of material to absorb energy when deformed elastically
Description : There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance. a) True b) False
Description : The dynamic load-carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. (a) True (b) False
Description : Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False
Description : The dynamic load carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. a) True b) False
Description : Stribeck equation gives dynamic load capacity of the bearing. a) True b) False
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm
Last Answer : a) 27mm
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed
Last Answer : c) 41666.7N
Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm
Last Answer : b) 41.2mm
Description : Which of the following are not true for petroff’s equation? a) Shaft is considered concentric with the bearing b) Bearing is subjected to light load c) Is used to find coefficient of friction d) Frictional torque is given by fpr2l
Last Answer : d) Frictional torque is given by fpr2l
Description : Assertion (A): In anti-friction bearings, the frictional resistance is very low as the shaft held by it remains in floating condition by the hydrodynamic pressure developed by the lubricant. [IES-2006] Reason (R): In hydrodynamic ... of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (d) A is false but R is true
Description : The hub is treated as a solid shaft while calculating torsional shear stress in the hub. a) True b) False
Description : Solid shaft is costlier than hollow shaft of same weight. a) True b) False
Description : The strength of hollow shaft is more than the strength of solid shaft of same weight. a) True b) False
Last Answer : a) True
Description : The stiffness of solid shaft is more than the stiffness of hollow shaft with same weight. a) True b) False
Description : Hot rolling produces a stronger shaft then cold rolling. a) True b) False
Description : Counter shaft is a secondary shaft. a) True b) False
Description : Shaft is rotating machine element. A. True B. False
Last Answer : A. True
Description : Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage
Last Answer : (a) Inner race
Description : Cotter joint is a permanent fastening. a) true b) false
Last Answer : b) false
Description : If shaft diameter is 30mm and number of pins emplaced are 6, then the diameter of the pin will be? a) 6.4mm b) 5.6mm c) 6.1mm d) 5.9mm
Last Answer : c) 6.1mm
Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5
Last Answer : c) 4
Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm
Last Answer : b) 140mm
Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm
Last Answer : a) 100mm
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed
Last Answer : b) 51.6N/mm2
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed
Last Answer : b) 25.8N/mm2
Description : The shaft is always stepped with ________ diameter at the middle portion and __________ diameter at the shaft ends. a) Minimum, maximum b) Maximum, minimum c) Minimum, minimum d) Zero, infinity
Last Answer : b) Maximum, minimum