Define the term BUS related to microprocessor/controller and list different buses used in microcontroller.

Define the term BUS related to microprocessor/controller and list different buses used in microcontroller.
by

1 Answer

Answer :

BUS: A Bus is a set of physical connections used for communication between CPU and peripherals.

Different buses used in microcontroller are:

1. Address Bus

2. Data Bus

3. Control Bus
by

Related questions

Differentiate between (i) Harvard and Von-neuman architecture (ii) Microprocessor and Microcontroller

Description : Differentiate between (i) Harvard and Von-neuman architecture (ii) Microprocessor and Microcontroller

Last Answer : i) Harvard Architecture and Von-neuman architecture ii) Microprocessor and Microcontroller

List specifications of 8051 microcontroller.

Description : List specifications of 8051 microcontroller.

Last Answer : 1) 8- bit data bus and 8- bit ALU. 2) 16- bit address bus - can access maximum 64KB of RAM and ROM. 3) On- chip RAM -128 bytes (Data Memory) 4) On- chip ROM - 4 KB ( ... 0592 MHz 9) Has power down and idle mode in microcontroller when no operation is performed. 10) Six interrupts are available.

Explain the various selection factors of microcontroller suitable for application.

Description : Explain the various selection factors of microcontroller suitable for application.

Last Answer : The selection of microcontroller depends upon the type of application. The following factors must be considered while selecting the microcontroller.  1. Word length: The word length of ... and for lesser production EPROM version or CPU version with external program memory is suitable

State and explain the need of the following development tools microcontroller board: (i) Editor (ii) Assembler (iii) Compiler (iv) Linker

Description : State and explain the need of the following development tools microcontroller board: (i) Editor (ii) Assembler (iii) Compiler (iv) Linker

Last Answer : 1) Editor: An editor is a program which helps you to construct your assembly language program in right format so that the assembler will translate it correctly to machine language. So, you can type your ... . Some examples of linker are ASEM-51 BL51, Keil u Vision Debugger, LX 51 Enhanced Linker etc

Draw the format of PSW register of 8051 microcontroller and explain the function of each bit.

Description : Draw the format of PSW register of 8051 microcontroller and explain the function of each bit.

Last Answer : 1. CY: Carry flag. This flag is set whenever there is a carry out from the D7 bit after an 8 bit addition or subtraction. It can also be set to 1 or 0 directly by instructions such as SETB C and ... the A register contains an odd number of 1s, then P=1. P=0 if A has an even number of 1s.

State any four important features of 8051 microcontroller.

Description : State any four important features of 8051 microcontroller.

Last Answer : Features of 8051 microcontroller:  1) 8- bit data bus and 8- bit ALU. 2) 16- bit address bus - can access maximum 64KB of RAM and ROM. 3) On- chip RAM -128 bytes (Data ... 0 and Timer 1, two external hardware interrupts- INT0 and INT1, Serial communication interrupt for both receive and transmit.

Draw and explain Internal port structure of Port 0 and Port 1 of 8051 microcontroller.

Description : Draw and explain Internal port structure of Port 0 and Port 1 of 8051 microcontroller.

Last Answer : Port-0 can be configured as a normal bidirectional I/O port or it can be used for address/data interfacing for accessing external memory. When control is '1', the port is used for address/data ... is not able to sink the current the pin voltage may rise, leading to a possible wrong reading.

Explain with sketch the interfacing of 4 ×4 matrix keypad with 8051 microcontroller.

Description : Explain with sketch the interfacing of 4 ×4 matrix keypad with 8051 microcontroller.

Last Answer : Interfacing keypad Fig. shows how to interface the 4 X 4 matrix keypad to two ports in microcontroller. The rows are connected to an output port and the columns are connected to an input port. To ... key has been pressed, the next task is to find out which column the pressed key belongs to.

Describe 8051 microcontroller as boolean processor.

Description : Describe 8051 microcontroller as boolean processor.

Last Answer : * 8051 processor is a CPU that can perform some operation on a data and gives the output. * The 8051 processor contains a complete Boolean processor for single-bit operations. * The internal RAM contains 128 ... CLR C means clear the carry bit SETB 20h means set the memory bit with bit address 20h.

Describe with sketches the procedure to troubleshoot the traffic light controller.

Description : Describe with sketches the procedure to troubleshoot the traffic light controller.

Last Answer : Considerations of Traffic Signal  1) Traffic light may have sensors integrated to provide real time traffic information  2) Based on the traffic information provided by the sensor, the duration of the ... 8) Capacity analysis of the intersection for current and future years using growth

Compare microprocessor and microcontroller

Description : Compare microprocessor and microcontroller

Last Answer : Application Microprocessor - Computer, Mobile phone, calculator Microcontroller - washing machine, microwave oven Microprocessor Microcontroller Do not have inbuilt RAM or ROM ... access Less multifunction pins on the IC Many multifunction pins on the IC

What is the difference between a microcontroller and a microprocessor?

Description : What is the difference between a microcontroller and a microprocessor?

Last Answer : Compare microprocessor and microcontroller Microprocessor Microcontroller 1)Inbuilt RAM and ROM 1)Do not have inbuilt RAM or ROM 2)Inbuilt timer 2)Doesn't have inbuilt timer ... same memory 6)Many Multifunction pins on the IC  6)less multifunction Pins on IC.

A bus disconnect link is used to isolate _____________. A. one bus bar from another B. the generator circuit breaker from the bus C. different phases from the equalizer connection D. positive and negative buses from the neutral

Description : A bus disconnect link is used to isolate _____________. A. one bus bar from another B. the generator circuit breaker from the bus C. different phases from the equalizer connection D. positive and negative buses from the neutral

Last Answer : Answer: B

25 buses are running between two places P and Q. In how many ways can a person go from P to Q and return by a different bus? a) 300 b) 625 c) 600 d) 650

Description : 25 buses are running between two places P and Q. In how many ways can a person go from P to Q and return by a different bus? a) 300 b) 625 c) 600 d) 650

Last Answer : c) 600

When the generator buses are treated as load bus.

Description : When the generator buses are treated as load bus.

Last Answer : If the reactive power constraints of a generator bus violates the specified limits then the generator is treated as load bus.

There are 312, 260 and 156 students in class X, XI and XII respectively. Buses are to be hired to take these students to a picnic. Find the maximum number of students who can sit in a bus if each bus takes equal number of students (a) 52 (b) 56 (c) 48 (d) 63

Description : There are 312, 260 and 156 students in class X, XI and XII respectively. Buses are to be hired to take these students to a picnic. Find the maximum number of students who can sit in a bus if each bus takes equal number of students (a) 52 (b) 56 (c) 48 (d) 63

Last Answer : (a) 52

Which of the following buses available on computer system: a) Address Bus b) Data Bus c) System Bus d) All of Above e) None of These

Description : Which of the following buses available on computer system: a) Address Bus b) Data Bus c) System Bus d) All of Above e) None of These

Last Answer : d) All of Above

Busses start from a bus terminal with a speed of 20 km/hr at intervals of 10 minutes. What is the speed of a man coming from the opposite direction towards the bus terminal if he meets the buses at intervals of 8 minutes? a) 3 km/hr b) 4 km/hr c) 5 km/hr d) 7 km/hr e) None of these

Description : Busses start from a bus terminal with a speed of 20 km/hr at intervals of 10 minutes. What is the speed of a man coming from the opposite direction towards the bus terminal if he meets the buses at intervals of 8 minutes? a) 3 km/hr b) 4 km/hr c) 5 km/hr d) 7 km/hr e) None of these

Last Answer : Distance covered in 10 minutes at 20 kmph = distance covered in 8 minutes at (20+x) kmph 20× 10/60=8/60(20+x) 200 = 160 + 8x 8x = 40 x=40/8=5 kmph Answer: c)

In 2003, the people preferring to travel by bus represented approximately what per cent of the people preferring to travel by own vehicles, buses and rails together in the year? a) 46 b) 54 c) 22 d) 14 e) 37

Description : In 2003, the people preferring to travel by bus represented approximately what per cent of the people preferring to travel by own vehicles, buses and rails together in the year? a) 46 b) 54 c) 22 d) 14 e) 37

Last Answer : e) 37

In the year 2003, if all the buses reduced their rates by 40% and 50% of the people who preferred to travel by rail, now preferred buses, then how many people (in thousands) prefer to travel by bus? a) 1750 b) 1569 c) 1458 d) 1675 e) None of these

Description : In the year 2003, if all the buses reduced their rates by 40% and 50% of the people who preferred to travel by rail, now preferred buses, then how many people (in thousands) prefer to travel by bus? a) 1750 b) 1569 c) 1458 d) 1675 e) None of these

Last Answer : d) 1675

Mention the various types of buses in power system with specified quantities for each bus.

Description : Mention the various types of buses in power system with specified quantities for each bus.

Last Answer : • Load bus or PQ-bus (P and Q are specified- Voltage magnitude and angle are to be obtained) • Generator bus or voltage controlled bus or PV bus (P and V are specified- Voltage angle and Q are to be obtained)

In a load flow problem solved by newton-Raphson method with polar coordinates, the size of the Jactobian is 100 × 100. If there are 20 PV buses in addition to PQ buses and a slack bus, the total number of buses in the system is_____

Description : In a load flow problem solved by newton-Raphson method with polar coordinates, the size of the Jactobian is 100 × 100. If there are 20 PV buses in addition to PQ buses and a slack bus, the total number of buses in the system is_____

Last Answer : 61

A transport company is running five buses between two towns, which are 50 kms apart. Seating capacity of each bus is 50 passengers. Actually passengers carried by each bus were 75% of seating capacity. All buses ran on all days of the month. Each bus made one round trip per day. Passenger kms are: (a) 2,81,250 (b) 1,87,500 (c) 5,62,500 (d) None of the above

Description : A transport company is running five buses between two towns, which are 50 kms apart. Seating capacity of each bus is 50 passengers. Actually passengers carried by each bus were 75% of seating capacity. All buses ran on all days of ... (a) 2,81,250 (b) 1,87,500 (c) 5,62,500 (d) None of the above

Last Answer : (c) 5,62,500

For a 15-bus power system with 3 voltage controlled buses, the size of Jacobian matrix is

Description : For a 15-bus power system with 3 voltage controlled buses, the size of Jacobian matrix is

Last Answer : For a 15-bus power system with 3 voltage controlled buses, the size of Jacobian matrix is 25 x 25

The system unit of a personal computer typically contains all of the following except: A) Microprocessor B) Disk controller C) Serial interface D) Modem

Description : The system unit of a personal computer typically contains all of the following except: A) Microprocessor B) Disk controller C) Serial interface D) Modem

Last Answer : Answer : D

The system unit of a personal computer typically contains all of the following except: a. Microprocessor b. Disk controller c. Serial interface d. Modem

Description : The system unit of a personal computer typically contains all of the following except: a. Microprocessor b. Disk controller c. Serial interface d. Modem

Last Answer : Modem

What are the differences between microprocessor and micro controller.

Description : What are the differences between microprocessor and micro controller.

Last Answer : Ans-The microprocessor is the integration of a number of useful functions into a single IC package. These functions are: The ability to execute a stored set of instructions to carry out user defined ... contain a wealth of other modules such as Serial I/O Timers and Analogue to Digital Converters.

The system unit of a personal computer typically contains all of the following except: a. Microprocessor b. Disk controller c. Serial interface d. Modem

Description : The system unit of a personal computer typically contains all of the following except: a. Microprocessor b. Disk controller c. Serial interface d. Modem

Last Answer : d. Modem

The system unit of a personal computer typically contains all of the following except: a. Microprocessor b. Disk controller c. Serial interface d. Modem

Description : The system unit of a personal computer typically contains all of the following except: a. Microprocessor b. Disk controller c. Serial interface d. Modem

Last Answer : d. Modem

List out any two instructions of following addressing modes: (i) Immediate addressing. (ii) Register addressing.

Description : List out any two instructions of following addressing modes: (i) Immediate addressing. (ii) Register addressing.

Last Answer : (i) Immediate addressing instructions: 1. MOV A, #36H 2. MOV DPTR, #27A2H (ii) Register addressing. 1. MOV A, R0 2. MOV R7, A

List SFR in 8051.

Description : List SFR in 8051.

Last Answer : ACC and B registers - 8 bit each DPTR : [DPH:DPL] - 16 bit combined PC : Program Counter - 16 bits Stack pointer SP - 8 bit PSW : Program Status Word Port Latches ... , serial control Timer Registers (TCON,TMOD,TL0/1,TH0/1) Power control Interrupt Enable, Interrupt Priority

Draw block diagram of microcontroller based pick and place Robot. List the four movements required by this Robot.

Description : Draw block diagram of microcontroller based pick and place Robot. List the four movements required by this Robot.

Last Answer : Diagram : Explanation: The robot has three axes about which motion can occur. Rotation in a clockwise or anti-clock wise direction of the unit on its base Arm extension or ... . The gripper can be opened or closed by the piston in a linear cylinder extending or retracting as.

List some important loads to 6.6 kV buses.

Description : List some important loads to 6.6 kV buses. 

Last Answer : a. Auxiliary transformers. b. PHT motors. c. BFP motors.  d. CEP motors. e. CCW motors. f. Chiller motors. g. Pressuring pump motors. 

Define Buses and their types.

Description : Define Buses and their types.

Last Answer : Ans : BUSES : A bus is a collection of wires that acts as a communication path between CPU and other devices through signal transfer. The bus width determines the speed of data transmission. There are also local buses ... a single bit at a time so 8-bits bus can transfer 8-bits at a time and so on.

What is system bus in microprocessor?

Description : What is system bus in microprocessor?

Last Answer : System bus speed in microprocessors is the speed at which a processor sends/receives data from the motherboard's memory controller. It is also called the Front Side Bus (FSB) speed in the case of Intel CPUs.

What type of control pins are needed in a microprocessor to regulate traffic on the bus, in order to prevent two devices from trying to use it at the same time? A) Bus control B) Interrupts C) Bus arbitration D) Status

Description : What type of control pins are needed in a microprocessor to regulate traffic on the bus, in order to prevent two devices from trying to use it at the same time? A) Bus control B) Interrupts C) Bus arbitration D) Status

Last Answer : Answer : C

A physical connection between the microprocessor memory and other parts of the microcomputer is known as A) Path B) Address bus C) Route D) All of the above

Description : A physical connection between the microprocessor memory and other parts of the microcomputer is known as A) Path B) Address bus C) Route D) All of the above

Last Answer : Answer : B

What type of control pins are needed in a microprocessor to regulate traffic on the bus, in order to prevent two devices from trying to use it at the same time? a. Bus control b. Interrupts c. Bus arbitration d. Status

Description : What type of control pins are needed in a microprocessor to regulate traffic on the bus, in order to prevent two devices from trying to use it at the same time? a. Bus control b. Interrupts c. Bus arbitration d. Status

Last Answer : c. Bus arbitration

A physical connection between the microprocessor memory and other parts of the m9crocomputer is known as a. Path b. Address bus c. Route d. All of the above

Description : A physical connection between the microprocessor memory and other parts of the m9crocomputer is known as a. Path b. Address bus c. Route d. All of the above

Last Answer : b. Address bus

What does microprocessor speed depends on? a) Clock b) Data bus width c) Address bus width

Description : What does microprocessor speed depends on? a) Clock b) Data bus width c) Address bus width

Last Answer : c) Address bus width

What type of control pins are needed in a microprocessor to regulate traffic on the bus, in order to prevent two devices from trying to use it at the same time? a. Bus control b. Interrupts c. Bus arbitration d. Status

Description : What type of control pins are needed in a microprocessor to regulate traffic on the bus, in order to prevent two devices from trying to use it at the same time? a. Bus control b. Interrupts c. Bus arbitration d. Status

Last Answer : c. Bus arbitration

A physical connection between the microprocessor memory and other parts of the m9crocomputer is known as a. Path b. Address bus c. Route d. All of the above

Description : A physical connection between the microprocessor memory and other parts of the m9crocomputer is known as a. Path b. Address bus c. Route d. All of the above

Last Answer : b. Address bus

A physical connection between the microprocessor memory and other parts of the m9crocomputer is known as a. Path b. Address bus c. Route d. All of the above

Description : A physical connection between the microprocessor memory and other parts of the m9crocomputer is known as a. Path b. Address bus c. Route d. All of the above

Last Answer : b. Address bus

Consider a 32 - bit microprocessor, with a 16 - bit external data bus, driven by an 8 MHz input clock. Assume that the microprocessor has a bus cycle whose minimum duration equals four input clock cycles. What is the maximum data transfer rate for this microprocessor? (A) 8x106 bytes/sec (B) 4x106 bytes/sec (C) 16x106 bytes/sec (D) 4x109 bytes/sec

Description : Consider a 32 - bit microprocessor, with a 16 - bit external data bus, driven by an 8 MHz input clock. Assume that the microprocessor has a bus cycle whose minimum duration equals four input clock cycles. What ... (A) 8x106 bytes/sec (B) 4x106 bytes/sec (C) 16x106 bytes/sec (D) 4x109 bytes/sec 

Last Answer : (B) 4x106 bytes/sec

In 8086 microprocessor , the address bus is ________ bit wide A. 12 bit B. 10 bit C. 16 bit D. 20 bit

Description : In 8086 microprocessor , the address bus is ________ bit wide A. 12 bit B. 10 bit C. 16 bit D. 20 bit

Last Answer : In 8086 microprocessor, the address bus is 20 bit

Periodic testing by a shoreside support technician using a special camera which can detect potentially dangerous loose or corroded bus bar and controller connections is termed ______________. A. heat sensitive thermography B. visual pyrotronics C. corrosion electrolysis D. electric vibroanalysis

Description : Periodic testing by a shoreside support technician using a special camera which can detect potentially dangerous loose or corroded bus bar and controller connections is termed ______________. A. heat sensitive thermography B. visual pyrotronics C. corrosion electrolysis D. electric vibroanalysis

Last Answer : Answer: A

The +5 volt regulated power supply shown in the illustration is fed directly from the _______________. EL-0094 A. 115 volt AC bus B. Annunciator Module C. +24 volt supply D. Annunciator Controller

Description : The +5 volt regulated power supply shown in the illustration is fed directly from the _______________. EL-0094 A. 115 volt AC bus B. Annunciator Module C. +24 volt supply D. Annunciator Controller

Last Answer : Answer: C

Which topology requires acentral controller or hub? A) Mesh B) Star C) Bus D) Ring

Description : Which topology requires acentral controller or hub? A) Mesh B) Star C) Bus D) Ring

Last Answer : Star

Which network topology requires a central controller or hub? a) Star b) Mesh c) Ring d) Bus

Description : Which network topology requires a central controller or hub? a) Star b) Mesh c) Ring d) Bus

Last Answer : a) Star