The range of Mho's scale of hardness is from (A) 1 to 15 (B) 1 to 8 (C) 1 to10 (D) 0 to 10

The range of Mho's scale of hardness is from
(A) 1 to 15
(B) 1 to 8
(C) 1 to10
(D) 0 to 10
by

1 Answer

Answer :

(C) 1 to10
by

Related questions

Mho's scale of hardness, which consists of 10 standard minerals is used for the measurement of __________ hardness. (A) Scratch (B) Indentation (C) Dynamic (D) Rebound

Description : Mho's scale of hardness, which consists of 10 standard minerals is used for the measurement of __________ hardness. (A) Scratch (B) Indentation (C) Dynamic (D) Rebound

Last Answer : (A) Scratch

The softest material in Mho's scale (for measuring hardness) is (A) Talc (B) Gypsum (C) Rubber (D) None of these

Description : The softest material in Mho's scale (for measuring hardness) is (A) Talc (B) Gypsum (C) Rubber (D) None of these

Last Answer : (A) Talc

The softest material just next to talc in the Mhos scale is (A) Quartz (B) Gypsum (C) Feldspar (D) Fluorite

Description : The softest material just next to talc in the Mhos scale is (A) Quartz (B) Gypsum (C) Feldspar (D) Fluorite

Last Answer : (B) Gypsum

The hardest material just prior to diamond in Mho's scale is (A) Topaz (B) Carborundum (C) Corundum (D) Calcite

Description : The hardest material just prior to diamond in Mho's scale is (A) Topaz (B) Carborundum (C) Corundum (D) Calcite

Last Answer : (C) Corundum

The hardest material just prior to diamond in Mhos scale is (A) Topaz (B) Carborundum (C) Corundum (D) Calcite

Description : The hardest material just prior to diamond in Mhos scale is (A) Topaz (B) Carborundum (C) Corundum (D) Calcite

Last Answer : (C) Corundum

The softest material just next to talc in the Mho's scale is (A) Quartz (B) Gypsum (C) Feldspar (D) Fluorite

Description : The softest material just next to talc in the Mho's scale is (A) Quartz (B) Gypsum (C) Feldspar (D) Fluorite

Last Answer : (C) Feldspar

Maximum change in the hardness of martensite occurs in the carbon content range of __________ percent in steel. (A) 0.01 to 0.10 (B) 0.2 to 0.4 (C) 0.5 to 0.7 (D) 0.8 to 1.0

Description : Maximum change in the hardness of martensite occurs in the carbon content range of __________ percent in steel. (A) 0.01 to 0.10 (B) 0.2 to 0.4 (C) 0.5 to 0.7 (D) 0.8 to 1.0

Last Answer : (B) 0.2 to 0.4

Scale formation in boiler is controlled by (A) Preheating of feed water (B) Reduction in hardness, silica & alumina in feed water (C) Keeping the pH value of feed water just below 7 (D) Eliminating H2S in feed water

Description : Scale formation in boiler is controlled by (A) Preheating of feed water (B) Reduction in hardness, silica & alumina in feed water (C) Keeping the pH value of feed water just below 7 (D) Eliminating H2S in feed water

Last Answer : (B) Reduction in hardness, silica & alumina in feed water

Brinell Hardness Number (BHN) for talc is approximately in the range of (A) 1-5 (B) 20-30 (C) 100 -150 (D) 200 - 250

Description : Brinell Hardness Number (BHN) for talc is approximately in the range of (A) 1-5 (B) 20-30 (C) 100 -150 (D) 200 - 250

Last Answer : (B) 20-30

Brinell Hardness Number (BHN) for talc is approximately in the range of (A) 1-5 (B) 20-30 (C) 100-150

Description : Brinell Hardness Number (BHN) for talc is approximately in the range of (A) 1-5 (B) 20-30 (C) 100-150

Last Answer : Option B

AC circuits develop resistance, inductance, and capacitance. The inductive reactance of a circuit is expressed in _____________. A. ohms B. mhos C. henrys D. farads

Description : AC circuits develop resistance, inductance, and capacitance. The inductive reactance of a circuit is expressed in _____________. A. ohms B. mhos C. henrys D. farads

Last Answer : Answer: A

Alternating current circuits develop resistance, inductance, and capacitance. The capacitance of individual capacitors is expressed in _____________. A. ohms B. mhos C. henrys D. farads

Description : Alternating current circuits develop resistance, inductance, and capacitance. The capacitance of individual capacitors is expressed in _____________. A. ohms B. mhos C. henrys D. farads

Last Answer : Answer: D

Alternating current circuits develop resistance, inductance and capacitance. The inductance of a coil is expressed in _____________. A. ohms B. mhos C. henrys D. farads

Description : Alternating current circuits develop resistance, inductance and capacitance. The inductance of a coil is expressed in _____________. A. ohms B. mhos C. henrys D. farads

Last Answer : Answer: C

AC circuits possess characteristics of resistance, inductance, and capacitance. The capacitive reactance of a circuit is expressed in _____________. A. ohms B. mhos C. henrys D. farads

Description : AC circuits possess characteristics of resistance, inductance, and capacitance. The capacitive reactance of a circuit is expressed in _____________. A. ohms B. mhos C. henrys D. farads

Last Answer : Answer: A

A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?

Description : A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?

Last Answer : 240 volts.

Which of the following relays is used on long transmission lines ? (a) Impedance relay (b) Mho's relay (c) Reactance relay (d) None of the above

Description : Which of the following relays is used on long transmission lines ? (a) Impedance relay (b) Mho's relay (c) Reactance relay (d) None of the above

Last Answer : (b) Mho's relay

Conductance is measured in: A. Henries B. Mhos C. Hertz D. Watts

Description : Conductance is measured in: A. Henries B. Mhos C. Hertz D. Watts

Last Answer : Conductance is measured in: Mhos

What is the hardness gold on mohs scale?

Description : What is the hardness gold on mohs scale?

Last Answer : 2.5

What is the mohs scale hardness of iron ore?

Description : What is the mohs scale hardness of iron ore?

Last Answer : Depends on the ore- somewhere around a 6-8. Varies between hardand very hard. Also corrected spelling on the Mohs scale.

Mohars scale is used to determine the — of rocks. a. Hardness b. Luster c. Color d. None of these

Description : Mohars scale is used to determine the — of rocks. a. Hardness b. Luster c. Color d. None of these

Last Answer : a. Hardness

Diamond is what number on the Moh's hardness scale?

Description : Diamond is what number on the Moh's hardness scale?  

Last Answer : ANSWER: 10

Orthoclase is what number on Moh's hardness scale? w) 4 x) 5 y) 6 z) 7

Description : Orthoclase is what number on Moh's hardness scale? w) 4 x) 5 y) 6 z) 7

Last Answer : ANSWER: Y -- 6

Apatite is what number on Moh's (pron: moes: rhyme with toes) hardness scale? w) 1 x) 3 y) 5 z) 7

Description : Apatite is what number on Moh's (pron: moes: rhyme with toes) hardness scale? w) 1 x) 3 y) 5 z) 7

Last Answer : ANSWER: Y -- 5

Fluorite is what number on Moh's hardness scale? w) 1 x) 2 y) 3 z) 4

Description : Fluorite is what number on Moh's hardness scale? w) 1 x) 2 y) 3 z) 4

Last Answer : ANSWER: Z -- 4

Why are there a wide range of colours, hardness, crystal forms, luster and density found in minerals ? -SST 10th

Description : Why are there a wide range of colours, hardness, crystal forms, luster and density found in minerals ? -SST 10th

Last Answer : A wide range of colours, hardness, crystal forms, luster, and density is found in minerals because of the high levels of variations in physical and chemical conditions under which a mineral is formed.

Why are there a wide range of colours, hardness, crystal forms, lustre and density found in minerals? -SST 10th

Description : Why are there a wide range of colours, hardness, crystal forms, lustre and density found in minerals? -SST 10th

Last Answer : The ranges found in minerals are due to physical and chemical conditions.

The coefficient of hardness of stones used in road work should be greater than (A) 10 (B) 12 (C) 15 (D) 17

Description : The coefficient of hardness of stones used in road work should be greater than (A) 10 (B) 12 (C) 15 (D) 17

Last Answer : Answer: Option D

Silicon percentage in iron castings to have maximum hardness should be about (A) 0.3 (B) 0.5 (C) 0.8 (D) 2.5

Description : Silicon percentage in iron castings to have maximum hardness should be about (A) 0.3 (B) 0.5 (C) 0.8 (D) 2.5

Last Answer : (C) 0.8

A galvanometer of 65 Ω resistance gives full scale deflection with 4 mA current. In order to convert it into ammeter, the range of 10 A is connected with it, the shunt resistance should be a) 0.1 Ω b) 0.2 Ω c) 0.06 Ω d) 0.03 Ω

Description : A galvanometer of 65 Ω resistance gives full scale deflection with 4 mA current. In order to convert it into ammeter, the range of 10 A is connected with it, the shunt resistance should be a) 0.1 Ω b) 0.2 Ω c) 0.06 Ω d) 0.03 Ω

Last Answer : d) 0.03 Ω

In natural gas, the C/H ratio (by weight) varies in the range of(A) 3-4(B) 8-10(C) 15-17(D) 20-25

Description : In natural gas, the C/H ratio (by weight) varies in the range of (A) 3-4 (B) 8-10 (C) 15-17 (D) 20-25

Last Answer : (A) 3-4

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'D'? EL-0047 A. 7.8 ohms B. 8 ohms C. 3.6 ohms D. .36 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'D'? EL-0047 A. 7.8 ohms B. 8 ohms C. 3.6 ohms D. .36 ohms

Last Answer : Answer: C

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'R'? EL-0047 A. 6 ohms B. 6.8 ohms C. 1.7 ohms D. 167 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'R'? EL-0047 A. 6 ohms B. 6.8 ohms C. 1.7 ohms D. 167 ohms

Last Answer : Answer: A

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'X'? EL-0047 A. 8 ohms B. 6.2 ohms C. 1.57 ohms D. 150 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'X'? EL-0047 A. 8 ohms B. 6.2 ohms C. 1.57 ohms D. 150 ohms

Last Answer : Answer: A

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'C'? EL-0047 A. 1.3 ohms B. 4.8 ohms C. 13 ohms D. 121 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'C'? EL-0047 A. 1.3 ohms B. 4.8 ohms C. 13 ohms D. 121 ohms

Last Answer : Answer: C

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'A'? EL-0047 A. 10 ohms B. 100 ohms C. 200 ohms D. 1,000 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'A'? EL-0047 A. 10 ohms B. 100 ohms C. 200 ohms D. 1,000 ohms

Last Answer : Answer: C

Find the range of the given data : 25, 18, 20, 22, 16, 6, 17, 15, 12, 30, 32, 10, 19, 8, 11, 20 -Maths 9th

Description : Find the range of the given data : 25, 18, 20, 22, 16, 6, 17, 15, 12, 30, 32, 10, 19, 8, 11, 20 -Maths 9th

Last Answer : Here, the minimum and maximum values of given data are 6 and 32 respectively. Range = 32 – 6 = 26

Find the range of the given data : 25, 18, 20, 22, 16, 6, 17, 15, 12, 30, 32, 10, 19, 8, 11, 20 -Maths 9th

Description : Find the range of the given data : 25, 18, 20, 22, 16, 6, 17, 15, 12, 30, 32, 10, 19, 8, 11, 20 -Maths 9th

Last Answer : Here, the minimum and maximum values of given data are 6 and 32 respectively. Range = 32 – 6 = 26

The range of the data 25, 18, 20, 22, 16, 6, 17, 15, 12, 30, 32, 10, 19, 8, 11 and 20 is -Maths 9th

Description : The range of the data 25, 18, 20, 22, 16, 6, 17, 15, 12, 30, 32, 10, 19, 8, 11 and 20 is -Maths 9th

Last Answer : In conclusion, the range of data 25, 18, 20, 22, 16, 6, 17, 15, 12, 30, 32, 10, 19, 8, 11, and 20 is 26.

The range of the data 25, 18, 20, 22, 16, 6, 17, 15, 12, 30, 32, 10, 19, 8, 11 and 20 is -Maths 9th

Description : The range of the data 25, 18, 20, 22, 16, 6, 17, 15, 12, 30, 32, 10, 19, 8, 11 and 20 is -Maths 9th

Last Answer : (d) In a given data, maximum value = 32 and minimum value = 6 We know, range of the data = maximum value – minimum value = 32 – 6 = 26 Hence, the range of the given data is 26.

What is the resistance value indicated on the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'R'? EL-0047 A. 6.0 ohms B. 162.5 ohms C. 600 ohms D. 16,250 ohms

Description : What is the resistance value indicated on the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'R'? EL-0047 A. 6.0 ohms B. 162.5 ohms C. 600 ohms D. 16,250 ohms

Last Answer : Answer: C

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'F'? EL-0047 A. 0.6 ohms B. 6 ohms C. 9.6 ohms D. .38 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'F'? EL-0047 A. 0.6 ohms B. 6 ohms C. 9.6 ohms D. .38 ohms

Last Answer : Answer: A

A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the

Description : A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the resolution of the instrument will be (a) 100 mV (b) 99 mV (c) 9 mV (d) 1 mV 

Last Answer : d) 1mV 9.999v÷9999v

The project report of the reconnaissance survey should be accompanied by Index map area at a scale of 1 cm = ---- km. (a) 2.5 km* (b) 5.0 km (c) 10.0 km (d) 15.0 km (e) 20.0 km

Description : The project report of the reconnaissance survey should be accompanied by Index map area at a scale of 1 cm = ---- km. (a) 2.5 km* (b) 5.0 km (c) 10.0 km (d) 15.0 km (e) 20.0 km

Last Answer : (a) 2.5 km*

The project report of the reconnaissance survey should be accompanied by a map of the area at a scale of 1 cm= --- km. (a) 2.5 km (b) 5.0 km (c) 10.0 km (d) 15.0 km (e) 20.0 km*

Description : The project report of the reconnaissance survey should be accompanied by a map of the area at a scale of 1 cm= --- km. (a) 2.5 km (b) 5.0 km (c) 10.0 km (d) 15.0 km (e) 20.0 km*

Last Answer : (e) 20.0 km*

In ball mill operation, the feed size (Df in meters) and the ball diameter (Db in metres) are related as (where, K = grindability constant (varying from 0.9 to 1.4 in increasing order of hardness)) (A) Db 2 = K.Df (B) Db = K.Df (C) Db 3 = K.Df (D) Db 2 = K.Df

Description : In ball mill operation, the feed size (Df in meters) and the ball diameter (Db in metres) are related as (where, K = grindability constant (varying from 0.9 to 1.4 in increasing order of hardness)) (A) Db 2 = K.Df (B) Db = K.Df (C) Db 3 = K.Df (D) Db 2 = K.Df

Last Answer : (A) Db 2 = K.Df

Presence of 0.3 to 0.5% arsenic in copper increases its (A) Ductility (B) Malleability (C) Tenacity & hardness (D) Electrical conductivity

Description : Presence of 0.3 to 0.5% arsenic in copper increases its (A) Ductility (B) Malleability (C) Tenacity & hardness (D) Electrical conductivity

Last Answer : (C) Tenacity & hardness

With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Description : With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Last Answer : (A) Impact strength

The difference in one unit of Rockwell hardness number corresponds to a difference in the depth of indentation of __________ mm. (A) 0.001 (B) 0.01 (C) 0.002 (D) 0.02

Description : The difference in one unit of Rockwell hardness number corresponds to a difference in the depth of indentation of __________ mm. (A) 0.001 (B) 0.01 (C) 0.002 (D) 0.02

Last Answer : Option C

The normal range of filtration factor in an adult is (A) 0.10–0.15 (B) 0.16–0.21 (C) 0.25–0.30 (D) 0.35–0.40

Description : The normal range of filtration factor in an adult is (A) 0.10–0.15 (B) 0.16–0.21 (C) 0.25–0.30 (D) 0.35–0.40

Last Answer : Answer : B