In the phase shift method, How many circuits must be balanced? A. None of these B. 1 C. 4 D. 2

In the phase shift method, How many circuits must be balanced?
A. None of these
B. 1
C. 4
D. 2
by

1 Answer

Answer :

D. 2
by

Related questions

What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Description : What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Last Answer : D. A frequency modulated continuous wave

What term is used to describe a spread spectrum communications system in which a very fast binary bit stream is used to shift the phase of an RF carrier? A. Frequency hopping B. Direct sequence C. Binary phase-shift keying D. Phase compandored spread spectrum

Description : What term is used to describe a spread spectrum communications system in which a very fast binary bit stream is used to shift the phase of an RF carrier? A. Frequency hopping B. Direct sequence C. Binary phase-shift keying D. Phase compandored spread spectrum

Last Answer : B. Direct sequence

Assume a frequency of 4 MHz, determine the phase shift offered by the line in the above problem. A. 108.5˚ B. 106.5˚ C. 115.5˚ D. 166.5˚

Description : Assume a frequency of 4 MHz, determine the phase shift offered by the line in the above problem. A. 108.5˚ B. 106.5˚ C. 115.5˚ D. 166.5˚

Last Answer : D. 166.5˚

The modulation technique used by GSM cellular system A. Phase shift keying B. Frequency shift keying C. Gaussian minimum shift keying D. QAM

Description : The modulation technique used by GSM cellular system A. Phase shift keying B. Frequency shift keying C. Gaussian minimum shift keying D. QAM

Last Answer : C. Gaussian minimum shift keying

A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Description : A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Last Answer : D. 8.8 dB

What is the phase delay of an 800 Hz voice signal if the phase shift is 15 degrees? A. 1.25 µsec B. 52 µsec C. 83.33 µsec D. 26 µsec

Description : What is the phase delay of an 800 Hz voice signal if the phase shift is 15 degrees? A. 1.25 µsec B. 52 µsec C. 83.33 µsec D. 26 µsec

Last Answer : B. 52 µsec

How to produced 180° phase shift?

Description : How to produced 180° phase shift?

Last Answer : The most common way of achieving this kind of filter is using three identical cascaded resistor capacitor filters, which together produce a phase shift of zero at low frequencies, and 270 degrees at ... phase shift of 60 degrees and the whole filter circuit produces a phase shift of 180 degrees.

What is phase-shift oscillator?

Description : What is phase-shift oscillator?

Last Answer : A phase-shift oscillator is a simple electronic oscillator. It contains an inverting amplifier, and a feedback filter which 'shifts' the phase of the amplifier output by 180 degrees at the oscillation ... 180° at high frequencies, so that the phase shift at the desired oscillation frequency is 180°.

ECE Board Exam March 1996 Passive crossover components cause some frequencies to be delayed with respect to the other frequencies at the crossover point. A. Phase shift B. Phase correction C. Phase-error correction D. Time alignment

Description : ECE Board Exam March 1996 Passive crossover components cause some frequencies to be delayed with respect to the other frequencies at the crossover point. A. Phase shift B. Phase correction C. Phase-error correction D. Time alignment

Last Answer : A. Phase shift

Strong interference from one particular station can be eliminated by the use of A. noise limiters B. squelch circuits C. negative feedback D. wave traps in the antenna circuitry

Description : Strong interference from one particular station can be eliminated by the use of A. noise limiters B. squelch circuits C. negative feedback D. wave traps in the antenna circuitry

Last Answer : D. wave traps in the antenna circuitry

Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Description : Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Last Answer : A. 5.23 dB

And ITU-T specification code that deals with the telephone circuits. A. X series B. T series C. V series D. I series

Description : And ITU-T specification code that deals with the telephone circuits. A. X series B. T series C. V series D. I series

Last Answer : C. V series

______ is a term in the test language for noise testing in telephone circuits that means a one-syllable word consisting of a consonant, a vowel, and another consonant. A. Logatom B. Nosfer C. Ore D. Belcore

Description : ______ is a term in the test language for noise testing in telephone circuits that means a one-syllable word consisting of a consonant, a vowel, and another consonant. A. Logatom B. Nosfer C. Ore D. Belcore

Last Answer : A. Logatom

Three telephone circuits, each having an S/N ratio of 44 dB, are connected in tandem. What is the overall S/N ratio? A. 44 dB B. 39.2 dB C. 41 dB D. 43.52 dB

Description : Three telephone circuits, each having an S/N ratio of 44 dB, are connected in tandem. What is the overall S/N ratio? A. 44 dB B. 39.2 dB C. 41 dB D. 43.52 dB

Last Answer : B. 39.2 dB

One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. Heating of capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Description : One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. ... capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Last Answer : B. Heating of capacitor in the oscillator

What do you call the phenomenon in digital circuits that describe the duration of time a digital signal passes a circuit? A. Transmission time B. Elapsed time C. Propagation delay D. Travel delay

Description : What do you call the phenomenon in digital circuits that describe the duration of time a digital signal passes a circuit? A. Transmission time B. Elapsed time C. Propagation delay D. Travel delay

Last Answer : C. Propagation delay

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

Synchronous modems cost more than asynchronous modem because _______. A. They have larger bandwidth B. They are larger C. The production volume is larger D. They have clock recovery circuits

Description : Synchronous modems cost more than asynchronous modem because _______. A. They have larger bandwidth B. They are larger C. The production volume is larger D. They have clock recovery circuits

Last Answer : D. They have clock recovery circuits

What are the requirements for biasing circuits?

Description : What are the requirements for biasing circuits?

Last Answer : · The q point must be taken at the Centre of the active region of the output characteristics. · Stabilize the collector current against the temperature variations. · Make the q point independent of the transistor parameters. · When the transistor is replaced, it must be of same type.

What are the types of filter circuits?

Description : What are the types of filter circuits?

Last Answer : The types of filter circuits are Inductor filter Capacitor filter LC filter CLC or π filter

What are the areas of application of non-linear op- amp circuits?

Description : What are the areas of application of non-linear op- amp circuits?

Last Answer : 1. Industrial instrumentation 2. Communication 3. Signal processing

Justify the reasons for using current sources in integrated circuits.

Description : Justify the reasons for using current sources in integrated circuits.

Last Answer : (i) Superior insensitivity of circuit performance to power supply variations and temperature.  (ii) More economical than resistors in terms of die area required to provide bias currents of ... the high incremental resistance of current source results in high voltage gain at low supply voltages.

Mention the advantages of integrated circuits over discrete components.

Description : Mention the advantages of integrated circuits over discrete components.

Last Answer : *Miniaturisation and hence increased equipment density. *Cost reduction due to batch processing. *Increased system reliability due to the elimination of soldered joints. *Improved functional performance. *Matched devices. *Increased operating speeds. *Reduction in power consumption.

A satellite stay in orbit because the following two factors are balanced A. Satellite weight and speed B. Gravitational force and centrifugal force C. Centripetal force and speed D. Satellite weight and the pull of the moon and sun

Description : A satellite stay in orbit because the following two factors are balanced A. Satellite weight and speed B. Gravitational force and centrifugal force C. Centripetal force and speed D. Satellite weight and the pull of the moon and sun

Last Answer : B. Gravitational force and centrifugal force

What mixer type has the lowest spurious signals? A. Double-balanced B. Single-balanced C. Super-heterodyner D. Heterodyner

Description : What mixer type has the lowest spurious signals? A. Double-balanced B. Single-balanced C. Super-heterodyner D. Heterodyner

Last Answer : A. Double-balanced

What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Description : What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Last Answer : B. A specially configured coaxial transmission line

A transmission line consisting of two conductors that have equal resistance per unit length. A. Unbalanced line B. Open-wire line C. Balanced line D. Coaxial line

Description : A transmission line consisting of two conductors that have equal resistance per unit length. A. Unbalanced line B. Open-wire line C. Balanced line D. Coaxial line

Last Answer : C. Balanced line

The output of a balanced modulator is ____________. A. LSB and USB B. LSB C. USB D. Carrier

Description : The output of a balanced modulator is ____________. A. LSB and USB B. LSB C. USB D. Carrier

Last Answer : A. LSB and USB

Transmission lines are either balanced or unbalanced with respect to _________. A. negative terminal B. input C. ground D. positive terminal

Description : Transmission lines are either balanced or unbalanced with respect to _________. A. negative terminal B. input C. ground D. positive terminal

Last Answer : C. ground

When a transmission line uses ground return, it is called a/an __________ line. A. ungrounded B. balanced C. unbalanced D. grounded

Description : When a transmission line uses ground return, it is called a/an __________ line. A. ungrounded B. balanced C. unbalanced D. grounded

Last Answer : C. unbalanced

ECE Board Exam March 1996 The standard that specifies a balanced interface cable that will operate bit rates up to 10 Mbps with in a span distances up to 1200 m. A. RS-423A B. RS-422A C. RS-550A D. RS-449A

Description : ECE Board Exam March 1996 The standard that specifies a balanced interface cable that will operate bit rates up to 10 Mbps with in a span distances up to 1200 m. A. RS-423A B. RS-422A C. RS-550A D. RS-449A

Last Answer : B. RS-422A

If the current ratios of the two or more elements must be held 5% and the phase angle to 3° the antenna is called a A. end fire array B. critical phased array C. broadband array D. wideband array

Description : If the current ratios of the two or more elements must be held 5% and the phase angle to 3° the antenna is called a A. end fire array B. critical phased array C. broadband array D. wideband array

Last Answer : B. critical phased array

Data can be changed from special code to temporal code by using (A) Shift registers (B) counters (C) Combinational circuits (D) A/D converters.

Description : Data can be changed from special code to temporal code by using (A) Shift registers (B) counters (C) Combinational circuits (D) A/D converters.

Last Answer : Ans: A Data can be changed from special code to temporal code by using Shift Registers. (A Register in which data gets shifted towards left or right when clock pulses are applied is known as a Shift Register.)

Which of the following contributes to the broadening of laser emission bandwidth? a. Doppler shift of moving atoms and molecules b. Amplification within the laser medium c. Coherence of the laser light d. Optical pumping of the laser transition

Description : Which of the following contributes to the broadening of laser emission bandwidth? a. Doppler shift of moving atoms and molecules b. Amplification within the laser medium c. Coherence of the laser light d. Optical pumping of the laser transition

Last Answer : a. Doppler shift of moving atoms and molecules

Which of the following systems is not used in radio detection and ranging? A. Frequency shift B. Frequency modulation C. Pulse radar D. Amplitude modulation

Description : Which of the following systems is not used in radio detection and ranging? A. Frequency shift B. Frequency modulation C. Pulse radar D. Amplitude modulation

Last Answer : D. Amplitude modulation

ECE Board Exam March 1996 The modulation system used for telegraphy is A. frequency-shift keying B. two-tone modulation C. pulse-code modulation D. single-tone modulation

Description : ECE Board Exam March 1996 The modulation system used for telegraphy is A. frequency-shift keying B. two-tone modulation C. pulse-code modulation D. single-tone modulation

Last Answer : A. frequency-shift keying

In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings

Description :  In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings of the wattmeters are 4 kW and 2 kW respectively, the later is being taken after reversing the connections of current coil. the ... kVAR B) 0.2 & 6 √3 kVAR C) 0.32 & 2 kVAR D) 0.32 & 2 √3 kVAR

Last Answer :  In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings of the wattmeters are 4 kW and 2 kW respectively, the later is being taken after reversing the ... of current coil. the power factor and reactive power of the load is 0.2 & 6 √3 kVAR

Two wattmeter method is employed to measure power in a 3 -phase balanced system with the current coil ...

Description : Two wattmeter method is employed to measure power in a 3 -phase balanced system with the current coil connected in the A and C lines. The phase sequence is ABC. If the wattmeter with its current coil in A -phase line reads zero, then the power factor of the 3 -phase load will be

Last Answer : Two wattmeter method is employed to measure power in a 3 -phase balanced system with the current coil connected in the A and C lines. The phase sequence is ABC. If the wattmeter with its current coil in A -phase line reads zero, then the power factor of the 3 -phase load will be 0.5 lagging.

Handheld phase sequence indicators are useful when ________. A. preparing to parallel alternators B. connecting lighting branch circuits C. troubleshooting DC motors D. connecting shore power lines to the ship

Description : Handheld phase sequence indicators are useful when ________. A. preparing to parallel alternators B. connecting lighting branch circuits C. troubleshooting DC motors D. connecting shore power lines to the ship

Last Answer : Answer: D

Define following terms used in A.C. circuits : (i) Cycle (ii) Rms value (iii) Phase difference (iv) Average value

Description : Define following terms used in A.C. circuits : (i) Cycle (ii) Rms value (iii) Phase difference (iv) Average value

Last Answer : (i) Cycle:   A complete set of variation of an alternating quantity which is repeated at regular interval of time is called as a cycle. OR  Each repetition of an alternating quantity ... charge as is transferred by the alternating current during the same time under the same conditions. 

During Phase 2 of action potential in cardiac cell, depolarizing current through calcium channels is balanced by (a) Delayed rectifier potassium current (b) outward chloride channel (c) Both (a) and (b) (d) None of the above

Description : During Phase 2 of action potential in cardiac cell, depolarizing current through calcium channels is balanced by (a) Delayed rectifier potassium current (b) outward chloride channel (c) Both (a) and (b) (d) None of the above

Last Answer : Ans: A

A balanced three-phase, 50 Hz voltage is applied to a 3 phase, 4 pole, induction motor. When the motor is delivering rated output, the slip is found to be 0.05. The speed of the rotor m.m.f. relative to the rotor structure is (A) 1500 r.p.m. (B) 1425 r.p.m. (C) 25 r.p.m. (D) 75 r.p.m.

Description : A balanced three-phase, 50 Hz voltage is applied to a 3 phase, 4 pole, induction motor. When the motor is delivering rated output, the slip is found to be 0.05. The speed of the rotor m.m.f. relative to the rotor structure is (A) 1500 r.p.m. (B) 1425 r.p.m. (C) 25 r.p.m. (D) 75 r.p.m.

Last Answer : (D) 75 r.p.m.

Define balanced 3 phase load.

Description : Define balanced 3 phase load.

Last Answer : Balanced 3 phase Load: Balanced three phase load is defined as star or delta connection of three equal impedances having equal real parts and equal imaginary parts. It takes same current of equal magnitude and equal phase angle.

Define balanced and unbalanced load in three phase circuit.

Description : Define balanced and unbalanced load in three phase circuit.

Last Answer : Balanced Load: When all the imedances of 3 phases are equal in magnitude and of same nature then load is said to be balanced.  Unbalanced Load: When all the imedances of 3 phases are not equal in magnitude and of different nature then load is said to be unbalanced.

The minimum number of wattmeter(s) required to measure 3-phase, 3-wire balanced or unbalanced power is

Description : The minimum number of wattmeter(s) required to measure 3-phase, 3-wire balanced or unbalanced power is  A) 1 B) 2 C) 3 D) 4

Last Answer : B

What should be kVA rating of each transformer in V-V bank when three phase balanced load is

Description : What should be kVA rating of each transformer in V-V bank when three phase balanced load is 40 kVA ? (A) 19 (B) 28 (C) 37 (D) 23

Last Answer : What should be kVA rating of each transformer in V-V bank when three phase balanced load is 40 kVA ? (A) 19 (B) 28 (C) 37 (D) 23

Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L load is

Description : Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L load is

Last Answer : Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L load is constant

At a particular instant, the R-phase voltage of a balanced 3-phase system is + 30 V, and the Y-phase voltage is ...

Description : At a particular instant, the R-phase voltage of a balanced 3-phase system is + 30 V, and the Y-phase voltage is – 90 V. The voltage of B-phase at that instant is (A) + 120 V (B) – 120 V (C) – 60 V (D) + 60 V

Last Answer : At a particular instant, the R-phase voltage of a balanced 3-phase system is + 30 V, and the Y-phase voltage is – 90 V. The voltage of B-phase at that instant is + 60 V

Three equal impedances are first connected in delta across a 3 -phase balanced supply. If the same...

Description : Three equal impedances are first connected in delta across a 3 -phase balanced supply. If the same impedances are connected in star across the same supply then,

Last Answer : A