What is the phase delay of an 800 Hz voice signal if the phase shift is 15 degrees? A. 1.25 µsec B. 52 µsec C. 83.33 µsec D. 26 µsec

What is the phase delay of an 800 Hz voice signal if the phase shift is 15 degrees?
A. 1.25 µsec
B. 52 µsec
C. 83.33 µsec
D. 26 µsec
by

1 Answer

Answer :

B. 52 µsec
by

Related questions

To the nearest rupee, what is the net present value of a replacement project whose cash flows are -Rs.104,000; Rs.34,444; Rs.39,877; Rs.25,000; and Rs.52,800 for years 0 through 4, respectively? The firm has decided to assume that the appropriate cost of capital is 10% and the appropriate risk-free rate is 6%. A. Rs.15,115 B. Rs.26,798 C. Rs.33,346 D. Rs.48,121

Description : To the nearest rupee, what is the net present value of a replacement project whose cash flows are -Rs.104,000; Rs.34,444; Rs.39,877; Rs.25,000; and Rs.52,800 for years 0 through 4, respectively? The firm has decided to ... -free rate is 6%. A. Rs.15,115 B. Rs.26,798 C. Rs.33,346 D. Rs.48,121

Last Answer : C. Rs.33,346

The laser frequency when the light has the wavelength 800 nm is a. 375 x 10^12 Hz b. 475 x 10^15 Hz c. 375 x 10^9 Hz d. 375 x 10^18 Hz

Description : The laser frequency when the light has the wavelength 800 nm is a. 375 x 10^12 Hz b. 475 x 10^15 Hz c. 375 x 10^9 Hz d. 375 x 10^18 Hz

Last Answer : a. 375 x 10^12 Hz

If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Description : If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Last Answer : A. 34.61 ns

An AM transmitter is rated 100W at 100% modulation. How much power required for the carrier? A. 33.33 W B. 66.66 W C. 83.33 W D. 100 W

Description : An AM transmitter is rated 100W at 100% modulation. How much power required for the carrier? A. 33.33 W B. 66.66 W C. 83.33 W D. 100 W

Last Answer : B. 66.66 W

What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Description : What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Last Answer : D. A frequency modulated continuous wave

In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Description : In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Last Answer : B. 93

The numerical aperture of a fiber if the angle of acceptance is 15 degrees, is a. 017 b. 0.26 c. 0.50 d. 0.75

Description : The numerical aperture of a fiber if the angle of acceptance is 15 degrees, is a. 017 b. 0.26 c. 0.50 d. 0.75

Last Answer : b. 0.26

What is the reference frequency of CCIT phosphomeric noise measurement? A. 800 HzB. 1000 Hz C. 1500 Hz D. 3400 Hz

Description : What is the reference frequency of CCIT phosphomeric noise measurement? A. 800 Hz B. 1000 Hz C. 1500 Hz D. 3400 Hz

Last Answer : A. 800 Hz

What is the reference frequency of CCITT psophometric noise measurement? A. 800 Hz B. 1500 Hz C. 3400 Hz D. 1000 Hz

Description : What is the reference frequency of CCITT psophometric noise measurement? A. 800 Hz B. 1500 Hz C. 3400 Hz D. 1000 Hz

Last Answer : A. 800 Hz

____________ is the out-of-band signaling between toll central offices (Bell System Standard) A. 2,000 Hz B. 800 Hz C. 3,835 Hz D. 3700 Hz

Description : ____________ is the out-of-band signaling between toll central offices (Bell System Standard) A. 2,000 Hz B. 800 Hz C. 3,835 Hz D. 3700 Hz

Last Answer : D. 3700 Hz

The phase constant of a wave propagation with frequency of 35 radian/sec and time delay of 7.5 sec is a) 4.66 b) 262.5 c) 46.6 d) 26.25

Description : The phase constant of a wave propagation with frequency of 35 radian/sec and time delay of 7.5 sec is a) 4.66 b) 262.5 c) 46.6 d) 26.25

Last Answer : b) 262.5

Calculate natural frequency of damped vibration, if damping factor is 0.52 and natural frequency of the system is 30 rad/sec which consists of machine supported on springs and dashpots. A 21 rad/sec B 25.62 rad/sec C 20.22 Hz D 3.15 Hz

Description : Calculate natural frequency of damped vibration, if damping factor is 0.52 and natural frequency of the system is 30 rad/sec which consists of machine supported on springs and dashpots. A 21 rad/sec B 25.62 rad/sec C 20.22 Hz D 3.15 Hz

Last Answer : B 25.62 rad/sec

Calculate natural frequency of damped vibration, if damping factor is 0.52 and natural frequency of the system is 30 rad/sec which consists of machine supported on springs and dashpots. A 25.62 rad/sec B 20.78 rad/sec C 14.4 rad/sec D 15.33 rad/sec

Description : Calculate natural frequency of damped vibration, if damping factor is 0.52 and natural frequency of the system is 30 rad/sec which consists of machine supported on springs and dashpots. A 25.62 rad/sec B 20.78 rad/sec C 14.4 rad/sec D 15.33 rad/sec

Last Answer : A 25.62 rad/sec

Calculate natural frequency of damped vibration, if damping factor is 0.52 and A natural frequency of the system is 30 rad/sec which consists of machine supported on springs and dashpots. ( A )25.62 rad/sec ( B )20.78 rad/sec ( C )14.4 rad/sec ( D )15.33 rad/sec

Description : Calculate natural frequency of damped vibration, if damping factor is 0.52 and A natural frequency of the system is 30 rad/sec which consists of machine supported on springs and dashpots. ( A )25.62 rad/sec ( B )20.78 rad/sec ( C )14.4 rad/sec ( D )15.33 rad/sec

Last Answer : ( A )25.62 rad/sec

Calculate natural frequency of damped vibration, if damping factor is 0.52 and natural frequ the system is 30 rad/sec which consists of machine supported on springs and dashpots. a. 25.62 rad/secb. 20.78 rad/sec c. 14.4 rad/sec d. 15.33 rad/sec

Description : Calculate natural frequency of damped vibration, if damping factor is 0.52 and natural frequ the system is 30 rad/sec which consists of machine supported on springs and dashpots. a. 25.62 rad/secb. 20.78 rad/sec c. 14.4 rad/sec d. 15.33 rad/sec

Last Answer : a. 25.62 rad/sec

The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Description : The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Last Answer : A. 273 ms

Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Description : Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Last Answer : D. B and C above

What is the channel spacing for MF-HF voice frequencies? A. 2.8 kHz B. 500 Hz C. 3.5 kHz D. 3 kHz

Description : What is the channel spacing for MF-HF voice frequencies? A. 2.8 kHz B. 500 Hz C. 3.5 kHz D. 3 kHz

Last Answer : D. 3 kHz

A voice-grade circuit using the PTN has an ideal passband of A. 0 to 4 Hz B. 0 to 4 kHz C. 0 to 4 GHz D. 0 to 4 MHz

Description : A voice-grade circuit using the PTN has an ideal passband of A. 0 to 4 Hz B. 0 to 4 kHz C. 0 to 4 GHz D. 0 to 4 MHz

Last Answer : B. 0 to 4 kHz

In SPADE system, how many PCM-encoded voice band channels are there? A. 800 B. 600 C. 300 D. 240

Description : In SPADE system, how many PCM-encoded voice band channels are there? A. 800 B. 600 C. 300 D. 240

Last Answer : A. 800

How many voice band channels are there in a superjumbo group? A. 600 B. 900 C. 10,800 D. 3,600

Description : How many voice band channels are there in a superjumbo group? A. 600 B. 900 C. 10,800 D. 3,600

Last Answer : C. 10,800

What is the propagation delay when a signal is transmitter by an earth station to a geosynchronous satellite about 38,500 km above earth’s equator and then received by the same earth station? A. 256 msec B. 128 msec C. 300 msec D. 400 msec

Description : What is the propagation delay when a signal is transmitter by an earth station to a geosynchronous satellite about 38,500 km above earth’s equator and then received by the same earth station? A. 256 msec B. 128 msec C. 300 msec D. 400 msec

Last Answer : A. 256 msec

What do you call the phenomenon in digital circuits that describe the duration of time a digital signal passes a circuit? A. Transmission time B. Elapsed time C. Propagation delay D. Travel delay

Description : What do you call the phenomenon in digital circuits that describe the duration of time a digital signal passes a circuit? A. Transmission time B. Elapsed time C. Propagation delay D. Travel delay

Last Answer : C. Propagation delay

1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50'. What number is missing? -Riddles

Description : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50'. What number is missing? -Riddles

Last Answer : 22

What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Description : What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Last Answer : B. 3853 Hz

A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Description : A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Last Answer : C. 999.8 kHz, 1000 kHz, and 1000.2 kHz

A carrier signal has ______. A. Constant peak amplitude B. The information C. Frequency range 20-20000 Hz D. A varying amplitude

Description : A carrier signal has ______. A. Constant peak amplitude B. The information C. Frequency range 20-20000 Hz D. A varying amplitude

Last Answer : A. Constant peak amplitude

In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load,

Description : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

Last Answer : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is alternating rectangular pulses

What is the delay time for satellite transmissions from earth transmitter to earth receiver? A. 0.5 s B. 1s C. 5 ms D. 0.25 s

Description : What is the delay time for satellite transmissions from earth transmitter to earth receiver? A. 0.5 s B. 1s C. 5 ms D. 0.25 s

Last Answer : A. 0.5 s

What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Description : What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Last Answer : A. 0.5 s

A project has the following cash inflows Rs.34,444; Rs.39,877; Rs.25,000; and Rs.52,800 for years 1 through 4, respectively. The initial cash outflow is Rs.104,000. Which of the following four statements is correct concerning the project internal rate of return (IRR)? A. The IRR is less than 10%. B. The IRR is greater than or equal to 10%, but less than 14%. C. The IRR is greater than or equal to 14%, but less than 18%. D. The IRR is greater than or equal to 18%.

Description : A project has the following cash inflows Rs.34,444; Rs.39,877; Rs.25,000; and Rs.52,800 for years 1 through 4, respectively. The initial cash outflow is Rs.104,000. Which of the following four statements ... than or equal to 14%, but less than 18%. D. The IRR is greater than or equal to 18%.

Last Answer : C. The IRR is greater than or equal to 14%, but less than 18%.

f the temperature falls below 18 degrees, the heating is switched on. When the temperature reaches 21 degrees, the heating is switched off. What is the minimum set of test input values to cover all valid equivalence partitions? A. 15, 19 and 25 degrees B. 17, 18, 20 and 21 degrees C. 18, 20 and 22 degrees D. 16 and 26 degrees

Description : f the temperature falls below 18 degrees, the heating is switched on. When the temperature reaches 21 degrees, the heating is switched off. What is the minimum set of test input values to cover all valid equivalence ... 17, 18, 20 and 21 degrees C. 18, 20 and 22 degrees D. 16 and 26 degrees

Last Answer : A. 15, 19 and 25 degrees

A thermometer measures temperature in whole degrees only. If the temperature falls below 18 degrees, the heating is switched off. It is switched on again when the temperature reaches 21 degrees. What are the best values in degrees to cover all equivalence partitions? A. 15,19 and 25. B. 17,18 and19. C. 18, 20 and22. D. 16, 26 and 32.

Description : A thermometer measures temperature in whole degrees only. If the temperature falls below 18 degrees, the heating is switched off. It is switched on again when the temperature reaches 21 degrees. What are the best values in degrees to ... and 25. B. 17,18 and19. C. 18, 20 and22. D. 16, 26 and 32.

Last Answer : A. 15,19 and 25.

What carrier system multiplexes 96 voice band channels into a single 6.312 Mbps data signal? A. T1 carrier system B. T2 carrier system C. T1C carrier system D. T3 carrier system

Description : What carrier system multiplexes 96 voice band channels into a single 6.312 Mbps data signal? A. T1 carrier system B. T2 carrier system C. T1C carrier system D. T3 carrier system

Last Answer : B. T2 carrier system

ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the same as that of the intermediate frequency C. Generates a 1kHz note for Morse code reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Description : ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the ... reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Last Answer : C. Generates a 1kHz note for Morse code reception

What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Description : What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Last Answer : C. 125,000

What is the resulting pressure when one pound of air at 15 psia and 200 ˚F is heated at constant volume to 800 ˚F?  A.15 psia  B. 28.6 psia  C. 36.4 psia.  D. 52.1 psia Formula : T1/p1 = T2/p2 p2= p1T2 / T1

Description : What is the resulting pressure when one pound of air at 15 psia and 200 ˚F is heated at constant volume to 800 ˚F?  A.15 psia  B. 28.6 psia  C. 36.4 psia.  D. 52.1 psia Formula : T1/p1 = T2/p2 p2= p1T2 / T1

Last Answer : 28.6 psia

What term is used to describe a spread spectrum communications system in which a very fast binary bit stream is used to shift the phase of an RF carrier? A. Frequency hopping B. Direct sequence C. Binary phase-shift keying D. Phase compandored spread spectrum

Description : What term is used to describe a spread spectrum communications system in which a very fast binary bit stream is used to shift the phase of an RF carrier? A. Frequency hopping B. Direct sequence C. Binary phase-shift keying D. Phase compandored spread spectrum

Last Answer : B. Direct sequence

Assume a frequency of 4 MHz, determine the phase shift offered by the line in the above problem. A. 108.5˚ B. 106.5˚ C. 115.5˚ D. 166.5˚

Description : Assume a frequency of 4 MHz, determine the phase shift offered by the line in the above problem. A. 108.5˚ B. 106.5˚ C. 115.5˚ D. 166.5˚

Last Answer : D. 166.5˚

The modulation technique used by GSM cellular system A. Phase shift keying B. Frequency shift keying C. Gaussian minimum shift keying D. QAM

Description : The modulation technique used by GSM cellular system A. Phase shift keying B. Frequency shift keying C. Gaussian minimum shift keying D. QAM

Last Answer : C. Gaussian minimum shift keying

A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Description : A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Last Answer : D. 8.8 dB

How to produced 180° phase shift?

Description : How to produced 180° phase shift?

Last Answer : The most common way of achieving this kind of filter is using three identical cascaded resistor capacitor filters, which together produce a phase shift of zero at low frequencies, and 270 degrees at ... phase shift of 60 degrees and the whole filter circuit produces a phase shift of 180 degrees.

What is phase-shift oscillator?

Description : What is phase-shift oscillator?

Last Answer : A phase-shift oscillator is a simple electronic oscillator. It contains an inverting amplifier, and a feedback filter which 'shifts' the phase of the amplifier output by 180 degrees at the oscillation ... 180° at high frequencies, so that the phase shift at the desired oscillation frequency is 180°.

In the phase shift method, How many circuits must be balanced? A. None of these B. 1 C. 4 D. 2

Description : In the phase shift method, How many circuits must be balanced? A. None of these B. 1 C. 4 D. 2

Last Answer : D. 2

ECE Board Exam March 1996 Passive crossover components cause some frequencies to be delayed with respect to the other frequencies at the crossover point. A. Phase shift B. Phase correction C. Phase-error correction D. Time alignment

Description : ECE Board Exam March 1996 Passive crossover components cause some frequencies to be delayed with respect to the other frequencies at the crossover point. A. Phase shift B. Phase correction C. Phase-error correction D. Time alignment

Last Answer : A. Phase shift

What is considered the threshold of audibility at 3000 Hz? A. 10-12 W/m2 B. 10-16 W/m2 C. 10-12 W/cm2 D. 10-15 W/cm2

Description : What is considered the threshold of audibility at 3000 Hz? A. 10-12 W/m2 B. 10-16 W/m2 C. 10-12 W/cm2 D. 10-15 W/cm2

Last Answer : A. 10-12 W/m2

What would be the physical length of a tpical coaxial transmission line that is electrically one-quarter wavelength long at 14.1 MHz? A. 20 meters B. 3.51 meters C. 2.33 meters D. 0.25 meter

Description : What would be the physical length of a tpical coaxial transmission line that is electrically one-quarter wavelength long at 14.1 MHz? A. 20 meters B. 3.51 meters C. 2.33 meters D. 0.25 meter

Last Answer : B. 3.51 meters

How many FM stations would be accommodated I an ordinary TV channel? A. 33 B. 30 C. 40 D. 25

Description : How many FM stations would be accommodated I an ordinary TV channel? A. 33 B. 30 C. 40 D. 25

Last Answer : B. 30

The population of Khyber Pakhtunkhwa according to 2017 Census is: A. 27 Million B. 33.44 Million C. 15.54 Million D. 30.52 Million

Description : The population of Khyber Pakhtunkhwa according to 2017 Census is: A. 27 Million B. 33.44 Million C. 15.54 Million D. 30.52 Million

Last Answer : ANSWER: D

KPK The population of Khyber Pakhtunkhwa according to 2017 Census is: A. 27 Million B. 33.44 Million C. 15.54 Million D. 30.52 Million

Description : KPK The population of Khyber Pakhtunkhwa according to 2017 Census is: A. 27 Million B. 33.44 Million C. 15.54 Million D. 30.52 Million

Last Answer : ANSWER: D