Strong interference from one particular station can be eliminated by the use of A. noise limiters B. squelch circuits C. negative feedback D. wave traps in the antenna circuitry

Strong interference from one particular station can be eliminated by the use of
A. noise limiters
B. squelch circuits
C. negative feedback
D. wave traps in the antenna circuitry
by

1 Answer

Answer :

D. wave traps in the antenna circuitry
by

Related questions

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator or ferrite isolator in the feed line of the transmitter and duplexer C. By using a class C final amplifier with high driving power D. By installing a low-pass filter in the antenna feed line

Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line

Last Answer : A. Through installing a band-pass filter in the antenna feed line

When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Description : When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Last Answer : D. internal receiver noise.

In electronic circuits, DC voltages can be positive (+) or negative (-) when measured with respect to the _________. A. printed circuit board 'common' trace B. chassis, console frame or hull 'ground' C. analogue or digital circuitry 'common' bus D. all of the above

Description : In electronic circuits, DC voltages can be positive (+) or negative (-) when measured with respect to the _________. A. printed circuit board 'common' trace B. chassis, console frame or hull 'ground' C. analogue or digital circuitry 'common' bus D. all of the above

Last Answer : Answer: D

How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Description : How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Last Answer : D. Decrease the receiver squelch, gain.

The advantage of periscope antenna in microwave A. Minimize interference to and from other neighboring stations B. Shorten waveguide link C. Reduce tower height D. All of these

Description : The advantage of periscope antenna in microwave A. Minimize interference to and from other neighboring stations B. Shorten waveguide link C. Reduce tower height D. All of these

Last Answer : B. Shorten waveguide link

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

Noise that occurs via capacitive or inductive coupling in a cable. A. Crosstalk B. Quantizing noise C. Reference noise D. Tone interference

Description : Noise that occurs via capacitive or inductive coupling in a cable. A. Crosstalk B. Quantizing noise C. Reference noise D. Tone interference

Last Answer : A. Crosstalk

Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Description : Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Last Answer : C. Impulse noise

Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Description : Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Last Answer : A. Quantizing noise

Form of interference caused by rain or dust storms. A. Precipitation static B. Shot-noise C. Galactic noise D. Impulse noise

Description : Form of interference caused by rain or dust storms. A. Precipitation static B. Shot-noise C. Galactic noise D. Impulse noise

Last Answer : A. Precipitation static

nif stands for A. Non-intrinsic figure B. Noise improvement factor C. Narrow intermediate frequency D. Noise interference figure

Description : nif stands for A. Non-intrinsic figure B. Noise improvement factor C. Narrow intermediate frequency D. Noise interference figure

Last Answer : B. Noise improvement factor

_________ is the random and unpredictable electric signals from natural causes, both internal and external to the system. A. Interference B. Attenuation C. Distortion D. Noise

Description : _________ is the random and unpredictable electric signals from natural causes, both internal and external to the system. A. Interference B. Attenuation C. Distortion D. Noise

Last Answer : D. Noise

What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Description : What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Last Answer : C. Poor front-end selectivity

The band of frequencies least susceptible to atmospheric noise and interference is: A. 30 – 300 kHz B. 300 – 3000 kHz C. 3 – 30 MHz D. 300 – 3000 MHz

Description : The band of frequencies least susceptible to atmospheric noise and interference is: A. 30 – 300 kHz B. 300 – 3000 kHz C. 3 – 30 MHz D. 300 – 3000 MHz

Last Answer : D. 300 – 3000 MHz

What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Description : What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Last Answer : A. Interference to adjacent channel

Nif stands for A. Narrow intermediate frequency B. Noise interference figure C. Noise improvement factor D. Non-intrinsic fugure

Description : Nif stands for A. Narrow intermediate frequency B. Noise interference figure C. Noise improvement factor D. Non-intrinsic fugure

Last Answer : C. Noise improvement factor

Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference

Description : Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference

Last Answer : C. Out of the band

The random and unpredictable electric signal from natural causes, both internal and external to the system is know as ________. A. Distortion B. Noise C. Attenuation D. Interference

Description : The random and unpredictable electric signal from natural causes, both internal and external to the system is know as ________. A. Distortion B. Noise C. Attenuation D. Interference

Last Answer : B. Noise

An FM receiver whose intermediate frequency is 10.7 MHz, is experiencing image channel interference from a station transmitting on 121.1 MHz. If the local oscillator is tracking above, the receiver is tuned to A. 131.8 MHz B. 110.4 MHz C. 142.5 MHz D. 99.7 MHz

Description : An FM receiver whose intermediate frequency is 10.7 MHz, is experiencing image channel interference from a station transmitting on 121.1 MHz. If the local oscillator is tracking above, the receiver is tuned to A. 131.8 MHz B. 110.4 MHz C. 142.5 MHz D. 99.7 MHz

Last Answer : D. 99.7 MHz

Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Description : Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Last Answer : A. 5.23 dB

______ is a term in the test language for noise testing in telephone circuits that means a one-syllable word consisting of a consonant, a vowel, and another consonant. A. Logatom B. Nosfer C. Ore D. Belcore

Description : ______ is a term in the test language for noise testing in telephone circuits that means a one-syllable word consisting of a consonant, a vowel, and another consonant. A. Logatom B. Nosfer C. Ore D. Belcore

Last Answer : A. Logatom

The main benefit of light-wave communications over microwaves or any other communications media is a. Lower cost b. Better security c. Wider bandwidth d. Freedom from interference

Description : The main benefit of light-wave communications over microwaves or any other communications media is a. Lower cost b. Better security c. Wider bandwidth d. Freedom from interference

Last Answer : c. Wider bandwidth

Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Description : Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Last Answer : A. increases sensitivity to weak signals

A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Description : A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Last Answer : B. 174K

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Description : What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Last Answer : A. Low noise amplifier

ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Description : ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Last Answer : C. 174 K

Circuits that can be interconnected without additional circuitry are known as ____________ circuits.

Description : Circuits that can be interconnected without additional circuitry are known as ____________ circuits.

Last Answer : Compatible.

Which of the following was used as circuitry for first generation of computers? (1) Vacuum tube (2) Transistors (3) Integrated circuits (4) Microprocessors

Description : Which of the following was used as circuitry for first generation of computers? (1) Vacuum tube (2) Transistors (3) Integrated circuits (4) Microprocessors

Last Answer : Vacuum tube

How does the electric field strength of a standard broadcast station vary with the distance from the antenna? A. The field strength of a standard broadcast station vary with the distance from the antenna B. The field strength is directly proportional to the distance from the antenna C. The field strength remains constant regardless of the distance from the antenna D. The field strength varies inversely as the distance from the antenna

Description : How does the electric field strength of a standard broadcast station vary with the distance from the antenna? A. The field strength of a standard broadcast station vary with the distance from ... the distance from the antenna D. The field strength varies inversely as the distance from the antenna

Last Answer : D. The field strength varies inversely as the distance from the antenna

Earth station uses what type of antenna A. Despun antenna B. Helical antenna C. Toroidal antenna D. Cassegrain antenna

Description : Earth station uses what type of antenna A. Despun antenna B. Helical antenna C. Toroidal antenna D. Cassegrain antenna

Last Answer : D. Cassegrain antenna

A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW. What is the gain in dB, obtained by the use if the reflector. (Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Description : A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW ... Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Last Answer : B. 2.6

A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 kW. What is the gain in dB obtain by the use of the reflector ? ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Description : A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 ... ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Last Answer : D. 2.6

If the antenna current is doubled, the field strength at a particular position is A. doubled B. halved C. multiplied by a factor of four D. divided by a factor of four

Description : If the antenna current is doubled, the field strength at a particular position is A. doubled B. halved C. multiplied by a factor of four D. divided by a factor of four

Last Answer : A. doubled

ECE Board Exam March 1996 An antenna which is not resonant at a particular frequencies and so can be used over a wide band of frequencies and so can be used over a wide band of frequencies is called A. aperiodic B. boresight C. cassegrain D. top-loaded

Description : ECE Board Exam March 1996 An antenna which is not resonant at a particular frequencies and so can be used over a wide band of frequencies and so can be used over a wide band of frequencies is called A. aperiodic B. boresight C. cassegrain D. top-loaded

Last Answer : A. aperiodic

What is the proper procedure for suppressing electrical noise in a mobile station? A. Apply shielding and filtering where necessary B. Insulate a all plain sheet metal surfaces from each other C. Apply anti-static spray liberally to all nonmetallic D. Install filter capacitors in series with all dc wiring

Description : What is the proper procedure for suppressing electrical noise in a mobile station? A. Apply shielding and filtering where necessary B. Insulate a all plain sheet metal surfaces from each other C. ... -static spray liberally to all nonmetallic D. Install filter capacitors in series with all dc wiring

Last Answer : A. Apply shielding and filtering where necessary

What satellite system parameter represents the quality of a satellite or an earth station receiver? A. Gain-to-Equivalent Noise Temperature Ratio (G/Te) B. Energy of Bit-to-Noise Density Ratio (Eb/No) C. Carrier-to-Noise Density Ratio (C/No) D. Bit energy

Description : What satellite system parameter represents the quality of a satellite or an earth station receiver? A. Gain-to-Equivalent Noise Temperature Ratio (G/Te) B. Energy of Bit-to-Noise Density Ratio (Eb/No) C. Carrier-to-Noise Density Ratio (C/No) D. Bit energy

Last Answer : A. Gain-to-Equivalent Noise Temperature Ratio (G/Te)

A particular circuit that rids FM of noise A. Detector B. Discriminator C. Phase Shifter D. Limiter

Description : A particular circuit that rids FM of noise A. Detector B. Discriminator C. Phase Shifter D. Limiter

Last Answer : D. Limiter

What particular circuit that rids FM of noise? A. HPF B. Phase shifter C. Limiter D. LPF

Description : What particular circuit that rids FM of noise? A. HPF B. Phase shifter C. Limiter D. LPF

Last Answer : C. Limiter

The antenna efficiency of an HF grounded vertical antenna can be made comparable to that of a half-wave antenna A. By installing a good ground radial system B. By isolating the coax shield from ground C. By shortening the vertical D. By lengthening the vertical

Description : The antenna efficiency of an HF grounded vertical antenna can be made comparable to that of a half-wave antenna A. By installing a good ground radial system B. By isolating the coax shield from ground C. By shortening the vertical D. By lengthening the vertical

Last Answer : A. By installing a good ground radial system

Where are the current nodes in a half-wave antenna? A. At the ends B. At the center C. Three-quarters of the way from the feed point toward the end D. One-half of the way from the feed point toward the end

Description : Where are the current nodes in a half-wave antenna? A. At the ends B. At the center C. Three-quarters of the way from the feed point toward the end D. One-half of the way from the feed point toward the end

Last Answer : A. At the ends

Where are the voltage nodes in a half-wave antenna? A. At the ends B. Three-quarters of the way from the feed point toward the end C. One-half of the way from the feed point toward the end D. At the feed point

Description : Where are the voltage nodes in a half-wave antenna? A. At the ends B. Three-quarters of the way from the feed point toward the end C. One-half of the way from the feed point toward the end D. At the feed point

Last Answer : D. At the feed point

The rhombic antenna is primarily used for A. ground wave propagation B. space wave propagation C. ionosphere scatter propagation D. sky wave propagation

Description : The rhombic antenna is primarily used for A. ground wave propagation B. space wave propagation C. ionosphere scatter propagation D. sky wave propagation

Last Answer : D. sky wave propagation

An antenna with unity gain A. Rhombic B. Half-wave dipole C. Isotropic D. Whip

Description : An antenna with unity gain A. Rhombic B. Half-wave dipole C. Isotropic D. Whip

Last Answer : C. Isotropic

What determines antenna polarization? A. The frequency of the radiated wave B. The direction of the radiated wave C. The direction of the magnetic field vector D. The direction of the electric field vector

Description : What determines antenna polarization? A. The frequency of the radiated wave B. The direction of the radiated wave C. The direction of the magnetic field vector D. The direction of the electric field vector

Last Answer : D. The direction of the electric field vector

_____ is an antenna with a number of half-wave antenna on it. A. Antenna array B. Tower C. Omni-directional D. Rhombic

Description : _____ is an antenna with a number of half-wave antenna on it. A. Antenna array B. Tower C. Omni-directional D. Rhombic

Last Answer : A. Antenna array

A device that converts high frequency current into electromagnetic wave. A. Antenna B. Loudspeaker C. Microphone D. Transducer

Description : A device that converts high frequency current into electromagnetic wave. A. Antenna B. Loudspeaker C. Microphone D. Transducer

Last Answer : A. Antenna

For a space wave transmission, the radio horizon distance of a receiving antenna with a height of 64 meters is approximately A. 8 km B. 32 km C. 64 km D. 256 km

Description : For a space wave transmission, the radio horizon distance of a receiving antenna with a height of 64 meters is approximately A. 8 km B. 32 km C. 64 km D. 256 km

Last Answer : B. 32 km