What do you call the phenomenon in digital circuits that describe the duration of time a digital signal passes a circuit? A. Transmission time B. Elapsed time C. Propagation delay D. Travel delay

What do you call the phenomenon in digital circuits that describe the duration of time a
digital signal passes a circuit?
A. Transmission time
B. Elapsed time
C. Propagation delay
D. Travel delay
by

1 Answer

Answer :

C. Propagation delay
by

Related questions

The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Description : The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Last Answer : A. 273 ms

What is the propagation delay when a signal is transmitter by an earth station to a geosynchronous satellite about 38,500 km above earth’s equator and then received by the same earth station? A. 256 msec B. 128 msec C. 300 msec D. 400 msec

Description : What is the propagation delay when a signal is transmitter by an earth station to a geosynchronous satellite about 38,500 km above earth’s equator and then received by the same earth station? A. 256 msec B. 128 msec C. 300 msec D. 400 msec

Last Answer : A. 256 msec

What is the propagation velocity of a signal in a transmission line whose inductance and capacitance are 5μH/m and 20μF/m respectively? A. 100x103 m/s B. 100 m/s C. 10x103 m/s D. 100x106 m/s

Description : What is the propagation velocity of a signal in a transmission line whose inductance and capacitance are 5μH/m and 20μF/m respectively? A. 100x103 m/s B. 100 m/s C. 10x103 m/s D. 100x106 m/s

Last Answer : A. 100x103 m/s

What do you call a transmission line used specifically for the purpose of achieving delay? A. Delay line B. Flat line C. Resonant line D. Non-resonant line

Description : What do you call a transmission line used specifically for the purpose of achieving delay? A. Delay line B. Flat line C. Resonant line D. Non-resonant line

Last Answer : A. Delay line

________ dispersion is caused by the difference in the propagation times of light rays that take different paths down a fiber. a. Material dispersion b. Wavelength dispersion c. Modal dispersion d. Delay dispersion

Description : ________ dispersion is caused by the difference in the propagation times of light rays that take different paths down a fiber. a. Material dispersion b. Wavelength dispersion c. Modal dispersion d. Delay dispersion

Last Answer : c. Modal dispersion

The round-trip propagation delay between two earth stations through a geosynchronous satellite is A. 500 to 600 ms B. 300 to 400 ms C. 600 to 700 ms D. 400 to 500 ms

Description : The round-trip propagation delay between two earth stations through a geosynchronous satellite is A. 500 to 600 ms B. 300 to 400 ms C. 600 to 700 ms D. 400 to 500 ms

Last Answer : A. 500 to 600 ms

The maximum propagation delay of a geostationary satellite is A. 278 ms B. 239 ms C. 300 ms D. 250 ms

Description : The maximum propagation delay of a geostationary satellite is A. 278 ms B. 239 ms C. 300 ms D. 250 ms

Last Answer : A. 278 ms

What is the minimum propagation delay of a geostationary satellite? A. 278 ms B. 239 ms C. 300 ms D. 600 ms

Description : What is the minimum propagation delay of a geostationary satellite? A. 278 ms B. 239 ms C. 300 ms D. 600 ms

Last Answer : B. 239 ms

The phenomenon of change in direction of light when it passes from one medium to another is called - (1) Propagation (2) Reflection (3) Refraction (4) Dispersion

Description : The phenomenon of change in direction of light when it passes from one medium to another is called - (1) Propagation (2) Reflection (3) Refraction (4) Dispersion

Last Answer : (3) Refraction Explanation: Refraction is the change in direction of wave propagation due to a change in its transmission medium. Due to the change of medium, the phase velocity of the wave is changed but its frequency remains constant.

The phenomenon of change in direction of light when it passes from one medium to another is called (1) Propagation (2) Reflection (3) Refraction (4) Dispersion

Description : The phenomenon of change in direction of light when it passes from one medium to another is called (1) Propagation (2) Reflection (3) Refraction (4) Dispersion

Last Answer : Refraction

Digital transmission provides a higher level of signal quality than analog transmission because A. repeaters regenerate digital pulses and remove distorstion B. digital signals are easier to sample than analog signals C. digital signals are smaller than analog signals and cannot easily be distorted D. analog signals are continuous and not easily distorted.

Description : Digital transmission provides a higher level of signal quality than analog transmission because A. repeaters regenerate digital pulses and remove distorstion B. digital signals are easier to sample than ... and cannot easily be distorted D. analog signals are continuous and not easily distorted.

Last Answer : A. repeaters regenerate digital pulses and remove distorstion

What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Description : What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Last Answer : A. 0.5 s

What is transit time (time delay) of a 50-ft length transmission line of the above problem? A. 50 ns B. 100 ns C. 75 ns D. 65 ns

Description : What is transit time (time delay) of a 50-ft length transmission line of the above problem? A. 50 ns B. 100 ns C. 75 ns D. 65 ns

Last Answer : C. 75 ns

Suppose that the one-way propagation delay for a 100 Mbps Ethernet having 48-bit jamming signal is 1.04 micro-seconds. The minimum frame size in bits is: a. 112 b. 160 c. 208 d. 256

Description : Suppose that the one-way propagation delay for a 100 Mbps Ethernet having 48-bit jamming signal is 1.04 micro-seconds. The minimum frame size in bits is: a. 112 b. 160 c. 208 d. 256

Last Answer : d. 256

Suppose the round trip propagation delay for a 10 Mbps Ethernet having 48-bit jamming signal is 46.4 ms. The minimum frame size is a. 94 b. 416 c. 464

Description : Suppose the round trip propagation delay for a 10 Mbps Ethernet having 48-bit jamming signal is 46.4 ms. The minimum frame size is a. 94 b. 416 c. 464

Last Answer : c. 464

An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.

Description : An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.

Last Answer : Maximum time taken for all flip-flops to stabilize is 75ns x 8 + 50 = 650ns. Frequency of operation must be less than 1/650ns = 1.5 MHz.

What is the phase delay of an 800 Hz voice signal if the phase shift is 15 degrees? A. 1.25 µsec B. 52 µsec C. 83.33 µsec D. 26 µsec

Description : What is the phase delay of an 800 Hz voice signal if the phase shift is 15 degrees? A. 1.25 µsec B. 52 µsec C. 83.33 µsec D. 26 µsec

Last Answer : B. 52 µsec

A sender uses the Stop-and-Wait ARQ protocol for reliable transmission of frames. Frames are of size 1000 bytes and the transmission rate at the sender is 80 Kbps (1Kbps = 1000 bits/second). Size of an acknowledgement is 100 bytes and the transmission rate at the receiver is 8 Kbps. The one-way propagation delay is 100 milliseconds. Assuming no frame is lost, the sender throughput is __________ bytes/second. a. 2500 b. 2000 c. 1500 d. 500

Description : A sender uses the Stop-and-Wait ARQ protocol for reliable transmission of frames. Frames are of size 1000 bytes and the transmission rate at the sender is 80 Kbps (1Kbps = 1000 bits/second). Size of ... is lost, the sender throughput is __________ bytes/second. a. 2500 b. 2000 c. 1500 d. 500

Last Answer : a. 2500

In a token ring network the transmission speed is 10^7 bps and the propagation speed is 200 metres/micro second. The 1- bit delay in this network is equivalent to: a. 500 metres of cable. b. 200 metres of cable. c. 20 metres of cable. d. 50 metres of cable

Description : In a token ring network the transmission speed is 10^7 bps and the propagation speed is 200 metres/micro second. The 1- bit delay in this network is equivalent to: a. 500 metres of cable. b. 200 metres of cable. c. 20 metres of cable. d. 50 metres of cable

Last Answer : c. 20 metres of cable.

The digital logic family which has the lowest propagation delay time is (A) ECL (B) TTL (C) CMOS (D) PMOS

Description : The digital logic family which has the lowest propagation delay time is (A) ECL (B) TTL (C) CMOS (D) PMOS

Last Answer : Ans: A The digital logic family which has the lowest propagation delay time is ECL (Lowest propagation delay time is possible in ECL because the transistors are used in difference amplifier configuration, in which they are never driven into saturation and thereby the storage time is eliminated).

In digital ICs, Schottky transistors are preferred over normal transistors because of their (A) Lower Propagation delay. (B) Higher Propagation delay. (C) Lower Power dissipation. (D) Higher Power dissipation.

Description : In digital ICs, Schottky transistors are preferred over normal transistors because of their (A) Lower Propagation delay. (B) Higher Propagation delay. (C) Lower Power dissipation. (D) Higher Power dissipation.

Last Answer : Ans: A Lower propagation delay as shottky transistors reduce the storage time delay by preventing the transistor from going deep into saturation.

What noise is a transient short-duration disturbance distributed essentially uniformly over the useful passband of a transmission system? A. Flicker noise B. Transit-time noise C. Shot noise D. Impulse noise

Description : What noise is a transient short-duration disturbance distributed essentially uniformly over the useful passband of a transmission system? A. Flicker noise B. Transit-time noise C. Shot noise D. Impulse noise

Last Answer : D. Impulse noise

What propagation condition is usually indicated when a VHF signal is received from a station over 500 miles away? A. D-layer absorption B. Faraday rotation C. Tropospheric ducting D. Moonbounce

Description : What propagation condition is usually indicated when a VHF signal is received from a station over 500 miles away? A. D-layer absorption B. Faraday rotation C. Tropospheric ducting D. Moonbounce

Last Answer : C. Tropospheric ducting

What propagation condition is usually indicated when a VHF signal is received from a station over 5000 miles away? A. Moonbounce B. D-layer absorption C. Tropospheric ducting D. Faraday rotation

Description : What propagation condition is usually indicated when a VHF signal is received from a station over 5000 miles away? A. Moonbounce B. D-layer absorption C. Tropospheric ducting D. Faraday rotation

Last Answer : C. Tropospheric ducting

A means of beyond the line-of-sight propagation of microwave signal. A. Space wave B. Microwave link C. Troposcatter D. Point-to-point

Description : A means of beyond the line-of-sight propagation of microwave signal. A. Space wave B. Microwave link C. Troposcatter D. Point-to-point

Last Answer : C. Troposcatter

ECE Board Exam November 1996 The loss in signal power as light travels down a fiber is A. attenuation B. propagation C. absorption D. scattering

Description : ECE Board Exam November 1996 The loss in signal power as light travels down a fiber is A. attenuation B. propagation C. absorption D. scattering

Last Answer : A. attenuation

Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Description : Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Last Answer : A. 5.23 dB

What is the phase coefficient in radians per unit length of a transmission line at the frequency of 10 MHz if the velocity of propagation is 2.5x108 m/s? A. 0.25 B. 2.5 C. 0.35 D. 3.5

Description : What is the phase coefficient in radians per unit length of a transmission line at the frequency of 10 MHz if the velocity of propagation is 2.5x108 m/s? A. 0.25 B. 2.5 C. 0.35 D. 3.5

Last Answer : A. 0.25

Referred to the dielectric constant of a transmission line material. A. Inductance and capacitance B. Velocity factor C. Characteristic impedance D. Propagation velocity

Description : Referred to the dielectric constant of a transmission line material. A. Inductance and capacitance B. Velocity factor C. Characteristic impedance D. Propagation velocity

Last Answer : B. Velocity factor

Fuses placed in series with a thermal trip-type circuit breaker are used for _____________. A. time-delay protection B. short-circuit protection C. short duration surge protection D. sustained overload protection

Description : Fuses placed in series with a thermal trip-type circuit breaker are used for _____________. A. time-delay protection B. short-circuit protection C. short duration surge protection D. sustained overload protection

Last Answer : Answer: B

Refers to the duration occupancy period of call during its use. A. Occupancy period B. Traffic time C. Use time D. Holding time

Description : Refers to the duration occupancy period of call during its use. A. Occupancy period B. Traffic time C. Use time D. Holding time

Last Answer : D. Holding time

Dispersion is used to describe the a. Splitting of white light into its component colors b. Propagation of light in straight lines c. Bending of a beam of light when it goes from one medium to another d. Bending of a beam light when it strikes a mirror

Description : Dispersion is used to describe the a. Splitting of white light into its component colors b. Propagation of light in straight lines c. Bending of a beam of light when it goes from one medium to another d. Bending of a beam light when it strikes a mirror

Last Answer : a. Splitting of white light into its component colors

________ is a typeof transmission impairment in which the signal loses strength due to the different propagation speeds of each frequency that makes up the signal. A) Attenuation B) Distortion C) Noise D) Decibel

Description : ________ is a typeof transmission impairment in which the signal loses strength due to the different propagation speeds of each frequency that makes up the signal. A) Attenuation B) Distortion C) Noise D) Decibel

Last Answer : Distortion

The distance a simple signal can travel in one period is called ………… A. Wavelength B. propagation speed C. Frequency D. both a and b

Description : The distance a simple signal can travel in one period is called ………… A. Wavelength B. propagation speed C. Frequency D. both a and b

Last Answer : A. Wavelength

Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Description : Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Last Answer : B. The approximation of the quantized signal

Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Description : Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Last Answer : The approximation of the quantized signal

A component that samples the microwave signal travelling in one direction down to the transmission line A. Isolator B. Combiner C. Directional coupler D. Attenuator

Description : A component that samples the microwave signal travelling in one direction down to the transmission line A. Isolator B. Combiner C. Directional coupler D. Attenuator

Last Answer : C. Directional coupler

What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Description : What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Last Answer : D. A frequency modulated continuous wave

A pair of current-carrying conductors is not considered a transmission line unless it is at least ___ λ long at the signal frequency. A. 0.1 B. 0.3 C. 0.2 D. 0.4

Description : A pair of current-carrying conductors is not considered a transmission line unless it is at least ___ λ long at the signal frequency. A. 0.1 B. 0.3 C. 0.2 D. 0.4

Last Answer : A. 0.1

What is the first symbol of a radio signal transmission having an amplitude modulated signal carrier, double side band? A. C B. B C. H D. A

Description : What is the first symbol of a radio signal transmission having an amplitude modulated signal carrier, double side band? A. C B. B C. H D. A

Last Answer : D. A

Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Description : Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Last Answer : B. 6 dB

In indication signal for a handshake form the DCE to the DTE in response to an active condition for the request to send a signal. A. Data transmission B. Clear to send C. Receive data D. Data set ready

Description : In indication signal for a handshake form the DCE to the DTE in response to an active condition for the request to send a signal. A. Data transmission B. Clear to send C. Receive data D. Data set ready

Last Answer : B. Clear to send

Technical study which deals with production, transport and delivery of a quality signal from source to destination. A. Transmission system engineering B. Communication system engineering C. Telephony engineering D. Telegraphic engineering

Description : Technical study which deals with production, transport and delivery of a quality signal from source to destination. A. Transmission system engineering B. Communication system engineering C. Telephony engineering D. Telegraphic engineering

Last Answer : A. Transmission system engineering

What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Description : What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Last Answer : A. Interference to adjacent channel

What is the advantage of sidetone? A. High transmission efficiency B. Results to a strengthened signal C. No energy dissipation D. Assures that the telephone is working

Description : What is the advantage of sidetone? A. High transmission efficiency B. Results to a strengthened signal C. No energy dissipation D. Assures that the telephone is working

Last Answer : D. Assures that the telephone is working

Quantization noise is caused by A. binary coding techniques B. serial transmission errors C. the synchronization between encoder and decoder D. the approximation of the quantized signal

Description : Quantization noise is caused by A. binary coding techniques B. serial transmission errors C. the synchronization between encoder and decoder D. the approximation of the quantized signal

Last Answer : D. the approximation of the quantized signal

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

ECE Board Exam March 1996 The expander in a companding device provides ___________. A. greater amplification for low signal levelsB. less amplification for low signal levels C. greater amplification for high signal levels D. lesser pressure for transmission

Description : ECE Board Exam March 1996 The expander in a companding device provides ___________. A. greater amplification for low signal levels B. less amplification for low signal levels C. greater amplification for high signal levels D. lesser pressure for transmission

Last Answer : B. less amplification for low signal levels

Noise occurring in the presence of signal resulting from a mismatch between the exact value of an analog signal and the closet available quantizing step in a digital coder. A. Quantizing noise B. Thermal noise C. Impulse noise D. Crosstalk

Description : Noise occurring in the presence of signal resulting from a mismatch between the exact value of an analog signal and the closet available quantizing step in a digital coder. A. Quantizing noise B. Thermal noise C. Impulse noise D. Crosstalk

Last Answer : A. Quantizing noise