How does a SSB transmitter output power normally expressed? A. Average power B. In terms of peak envelop power C. In terms of peak-to-peak power D. Peak power

How does a SSB transmitter output power normally expressed?
A. Average power
B. In terms of peak envelop power
C. In terms of peak-to-peak power
D. Peak power
by

1 Answer

Answer :

B. In terms of peak envelop power
by

Related questions

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Last Answer : C. Carrier power

An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak

Description : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

Last Answer : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

What modulation is normally used with digital data? A. AM B. FM C. SSB D. QPSK

Description : What modulation is normally used with digital data? A. AM B. FM C. SSB D. QPSK

Last Answer : D. QPSK

In the American standard, the aural transmitter maximum radiated power is _____ of peak visual transmitter power. A. 10 % B. 30 % C. 20 % D. 40 %

Description : In the American standard, the aural transmitter maximum radiated power is _____ of peak visual transmitter power. A. 10 % B. 30 % C. 20 % D. 40 %

Last Answer : C. 20 %

In the European standard, the aurial transmitter maximum radiated power is ______ of peak visual transmitter power. A. 10% B. 30% C. 20% D. 40%

Description : In the European standard, the aurial transmitter maximum radiated power is ______ of peak visual transmitter power. A. 10% B. 30% C. 20% D. 40%

Last Answer : C. 20%

External noise fields are measured in terms of _______. A. rms values B. dc values C. average values D. peak values

Description : External noise fields are measured in terms of _______. A. rms values B. dc values C. average values D. peak values

Last Answer : D. peak values

Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Description : Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Last Answer : D. Spark emission

An antenna “efficiency” is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x 100% C. Efficiency = (effective radiated power / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Description : An antenna efficiency is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x ... / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Last Answer : D. Efficiency = (radiation resistance / total resistance) x 100%

What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Description : What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Last Answer : C. The noise floor of the receiver

What is the effective radiated power of a repeater with 200 watts transmitter power output, 4 dB feline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 317 W B. 2000 W C. 126 W D. 260 W

Description : What is the effective radiated power of a repeater with 200 watts transmitter power output, 4 dB feline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 317 W B. 2000 W C. 126 W D. 260 W

Last Answer : A. 317 W

What is the effective radiated power of a repeater with 120 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 601 W B. 240 W C. 60 W D. 379 W

Description : What is the effective radiated power of a repeater with 120 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 601 W B. 240 W C. 60 W D. 379 W

Last Answer : C. 60 W

What is the effective radiated power of a repeater with 100 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 800 W B. 126 W C. 12.5 W D. 1260 W

Description : What is the effective radiated power of a repeater with 100 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 800 W B. 126 W C. 12.5 W D. 1260 W

Last Answer : B. 126 W

What is the effective radiated power of a repeater with 75 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 37.6 W B. 237 W C. 150 W D. 23.7 W

Description : What is the effective radiated power of a repeater with 75 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 37.6 W B. 237 W C. 150 W D. 23.7 W

Last Answer : A. 37.6 W

What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Description : What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Last Answer : D. 150 W

What is the effective radiated power of a repeater with 50 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 7 dB antenna gain? A. 300 W B. 315 W C. 31.5 W D. 69.9 W

Description : What is the effective radiated power of a repeater with 50 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 7 dB antenna gain? A. 300 W B. 315 W C. 31.5 W D. 69.9 W

Last Answer : C. 31.5 W

What is the effective radiated power of a repeater with 50 watts transmitter power output \, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 6 dB antenna gain? A. 158 W B. 39.7 W C. 251 W D. 69.9 W

Description : What is the effective radiated power of a repeater with 50 watts transmitter power output \, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 6 dB antenna gain? A. 158 W B. 39.7 W C. 251 W D. 69.9 W

Last Answer : B. 39.7 W

One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the high power output. The purpose of which is to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Last Answer : B. MOPA

What is meant by the term antenna efficiency? A. Efficiency = effective radiated power/transmitter output x 100% B. Efficiency = radiation resistance/ transmission resistance C. Efficiency = total resistance/radiation resistance x 100% D. Efficiency = radiation resistance/total resistance x 100%

Description : What is meant by the term antenna efficiency? A. Efficiency = effective radiated power/transmitter output x 100% B. Efficiency = radiation resistance/ transmission resistance C. Efficiency = total resistance/radiation resistance x 100% D. Efficiency = radiation resistance/total resistance x 100%

Last Answer : D. Efficiency = radiation resistance/total resistance x 100%

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

What type of modulation is used on voice and video signals? A. AM B. FM C. SSB D. QPSK

Description : What type of modulation is used on voice and video signals? A. AM B. FM C. SSB D. QPSK

Last Answer : B. FM

What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Description : What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Last Answer : C. 125,000

With which emission type is the capture-effect most pronounced? A. CW B. FM C. SSB D. AM

Description : With which emission type is the capture-effect most pronounced? A. CW B. FM C. SSB D. AM

Last Answer : B. FM

Used for time division multiplexing. A. Frequency modulation B. Pulsed modulation C. SSB D. Amplitude modulation

Description : Used for time division multiplexing. A. Frequency modulation B. Pulsed modulation C. SSB D. Amplitude modulation

Last Answer : B. Pulsed modulation

ECE Board Exam March 1996 SSB transmission requires only ______ of the bandwidth for a DSBFC transmission. A. ¼ B. 2/3 C. ½ D. ¾

Description : ECE Board Exam March 1996 SSB transmission requires only ______ of the bandwidth for a DSBFC transmission. A. ¼ B. 2/3 C. ½ D. ¾

Last Answer : C. ½

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

If an antenna has a gain of 3 dB, it increases the output of the transmitter by A. 10,000 times B. 1000 times C. 100 times D. 1 million times

Description : If an antenna has a gain of 3 dB, it increases the output of the transmitter by A. 10,000 times B. 1000 times C. 100 times D. 1 million times

Last Answer : B. 1000 times

Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Description : Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Last Answer : D. load connected to the output end of a transmission line

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

Which is the proper measurement of average power emitted by a pulsed laser? a. Energy x time b. Pulse energy x repetition rate c. Pulse energy / repetition rate d. Peak power x pulse length

Description : Which is the proper measurement of average power emitted by a pulsed laser? a. Energy x time b. Pulse energy x repetition rate c. Pulse energy / repetition rate d. Peak power x pulse length

Last Answer : b. Pulse energy x repetition rate

Cable attenuation is usually expressed in terms of a. Loss per foot b. dB/km c. intensity per mile d. voltage drop per inch

Description : Cable attenuation is usually expressed in terms of a. Loss per foot b. dB/km c. intensity per mile d. voltage drop per inch

Last Answer : b. dB/km

The vibration in a vehicle is normally expressed in the terms of the ______________. (A) displacement (B) velocity (C) acceleration (D) none of the above

Description : The vibration in a vehicle is normally expressed in the terms of the ______________. (A) displacement (B) velocity (C) acceleration (D) none of the above

Last Answer : (C) acceleration

The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Description : The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Last Answer : B. Effective Isotropic Radiated Power (EIRP)

What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Description : What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Last Answer : A. The power traveling from the transmitter to the antenna.

If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Description : If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Last Answer : D. 6 watts

A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Description : A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Last Answer : C. 49

How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Description : How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Last Answer : C. Use of regulated power supply

Determine the effective radiated power of 20 kW TV broadcast transmitter whose antenna has a field gain of 2. A. 40 kW B. 80,000 watts C. 40,000 watts D. 8,000 watts

Description : Determine the effective radiated power of 20 kW TV broadcast transmitter whose antenna has a field gain of 2. A. 40 kW B. 80,000 watts C. 40,000 watts D. 8,000 watts

Last Answer : B. 80,000 watts

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

A transmitter supplies 8 kW to the antenna when it is unmodulated, determine the total radiated power when modulated at 90%. A. 5 kW B. 20 kW C. 15 kW D. 8.36 kW

Description : A transmitter supplies 8 kW to the antenna when it is unmodulated, determine the total radiated power when modulated at 90%. A. 5 kW B. 20 kW C. 15 kW D. 8.36 kW

Last Answer : D. 8.36 kW

How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator or ferrite isolator in the feed line of the transmitter and duplexer C. By using a class C final amplifier with high driving power D. By installing a low-pass filter in the antenna feed line

Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line

Last Answer : A. Through installing a band-pass filter in the antenna feed line

The final power amplifier in an FM transmitter usually operates class ______. A. AB B. C C. B D. A

Description : The final power amplifier in an FM transmitter usually operates class ______. A. AB B. C C. B D. A

Last Answer : B. C

An AM transmitter is rated 100W at 100% modulation. How much power required for the carrier? A. 33.33 W B. 66.66 W C. 83.33 W D. 100 W

Description : An AM transmitter is rated 100W at 100% modulation. How much power required for the carrier? A. 33.33 W B. 66.66 W C. 83.33 W D. 100 W

Last Answer : B. 66.66 W

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : B. 2.656 watts

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : A. PAM

What is the primary advantage of DSBSC in AM? A. Reduce bandwidth over standard AM B. All of these C. It is simpler to transmit and receive than the standard AM D. No transmitter power is wasted in the carrier

Description : What is the primary advantage of DSBSC in AM? A. Reduce bandwidth over standard AM B. All of these C. It is simpler to transmit and receive than the standard AM D. No transmitter power is wasted in the carrier

Last Answer : D. No transmitter power is wasted in the carrier

ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Description : ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Last Answer : C. gain of the antenna

The product of antenna input power and the antenna power gain expressed in kW is called __. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Description : The product of antenna input power and the antenna power gain expressed in kW is called __. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Last Answer : A. Effective Radiated Power (ERP)

Power is always __________. A. a definite amount of energy B. all of these C. the rate at which energy is used D. expressed in watts

Description : Power is always __________. A. a definite amount of energy B. all of these C. the rate at which energy is used D. expressed in watts

Last Answer : B. all of these