What is the primary advantage of DSBSC in AM? A. Reduce bandwidth over standard AM B. All of these C. It is simpler to transmit and receive than the standard AM D. No transmitter power is wasted in the carrier

What is the primary advantage of DSBSC in AM?
A. Reduce bandwidth over standard AM
B. All of these
C. It is simpler to transmit and receive than the standard AM
D. No transmitter power is wasted in the carrier
by

1 Answer

Answer :

D. No transmitter power is wasted in the carrier
by

Related questions

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

What is the advantage of PTM over PAM? A. All of these B. Low sampling rate is required C. Much better noise immunity D. Simpler to generate

Description : What is the advantage of PTM over PAM? A. All of these B. Low sampling rate is required C. Much better noise immunity D. Simpler to generate

Last Answer : C. Much better noise immunity

An AM transmitter is rated 100W at 100% modulation. How much power required for the carrier? A. 33.33 W B. 66.66 W C. 83.33 W D. 100 W

Description : An AM transmitter is rated 100W at 100% modulation. How much power required for the carrier? A. 33.33 W B. 66.66 W C. 83.33 W D. 100 W

Last Answer : B. 66.66 W

The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Description : The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Last Answer : B. Effective Isotropic Radiated Power (EIRP)

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Last Answer : C. Carrier power

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

A single sideband emission in which the degree of carrier suppression enables the carrier to be reconstituted and to be used for demodulation. A. Reduce carrier single sideband emission B. Half carrier single sideband emission C. Full carrier single sideband emission D. Standard single sideband emission

Description : A single sideband emission in which the degree of carrier suppression enables the carrier to be reconstituted and to be used for demodulation. A. Reduce carrier single sideband emission ... single sideband emission C. Full carrier single sideband emission D. Standard single sideband emission

Last Answer : A. Reduce carrier single sideband emission

A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Description : A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Last Answer : D. 8.8 dB

A digital carrier facility used to transmit a DSI-formatted signal at 1.544. Mbps. A. T2 B. T1 C. T4 D. T3

Description : A digital carrier facility used to transmit a DSI-formatted signal at 1.544. Mbps. A. T2 B. T1 C. T4 D. T3

Last Answer : B. T1

Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Description : Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Last Answer : C. Varying of some parameters of a carrier such as its amplitude to transmit information

How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Description : How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Last Answer : D. Decrease the receiver squelch, gain.

In radio regulation, the first symbol in the designation of radio emission is ______. A. Bandwidth B. Nature of signal(s) modulation the main carrier C. Type of modulation of the main carrier D. Type of information to be transmitted

Description : In radio regulation, the first symbol in the designation of radio emission is ______. A. Bandwidth B. Nature of signal(s) modulation the main carrier C. Type of modulation of the main carrier D. Type of information to be transmitted

Last Answer : C. Type of modulation of the main carrier

How wide is the spectrum bandwidth of a single GSM carrier? A. 100 kHz B. 200 kHz C. 50 kHz D. 16 kHz

Description : How wide is the spectrum bandwidth of a single GSM carrier? A. 100 kHz B. 200 kHz C. 50 kHz D. 16 kHz

Last Answer : B. 200 kHz

The third symbol in the designation of radio emission under the ITU rules refers to A. Type of the modulation of the main carrier B. Bandwidth C. Nature of the signals modulating the main carrier D. Type of information to be transmitted

Description : The third symbol in the designation of radio emission under the ITU rules refers to A. Type of the modulation of the main carrier B. Bandwidth C. Nature of the signals modulating the main carrier D. Type of information to be transmitted

Last Answer : D. Type of information to be transmitted

The first symbol in the designation of radio emission under the ITU rules to A. Nature of signals modulating the main carrier B. Type of information to be transmitted C. Bandwidth D. Type of modulation of the main carrier

Description : The first symbol in the designation of radio emission under the ITU rules to A. Nature of signals modulating the main carrier B. Type of information to be transmitted C. Bandwidth D. Type of modulation of the main carrier

Last Answer : D. Type of modulation of the main carrier

Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Description : Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Last Answer : D. Spark emission

The first satellite to receive and transmit simultaneously A. Intelsat I B. Agila I C. Syncorn I D. Telstar I

Description : The first satellite to receive and transmit simultaneously A. Intelsat I B. Agila I C. Syncorn I D. Telstar I

Last Answer : D. Telstar I

Known to be the first satellite capable to receive and transmit simultaneously. A. Score B. Syncom I C. Telstar 1 D. Echo1

Description : Known to be the first satellite capable to receive and transmit simultaneously. A. Score B. Syncom I C. Telstar 1 D. Echo1

Last Answer : C. Telstar 1

Which of the following is not a way of minimizing if not eliminating noise? A. Use redundancy B. Increase transmitted power C. Reduce signaling rate D. Increase channel bandwidth

Description : Which of the following is not a way of minimizing if not eliminating noise? A. Use redundancy B. Increase transmitted power C. Reduce signaling rate D. Increase channel bandwidth

Last Answer : D. Increase channel bandwidth

In the American standard, the aural transmitter maximum radiated power is _____ of peak visual transmitter power. A. 10 % B. 30 % C. 20 % D. 40 %

Description : In the American standard, the aural transmitter maximum radiated power is _____ of peak visual transmitter power. A. 10 % B. 30 % C. 20 % D. 40 %

Last Answer : C. 20 %

In the European standard, the aurial transmitter maximum radiated power is ______ of peak visual transmitter power. A. 10% B. 30% C. 20% D. 40%

Description : In the European standard, the aurial transmitter maximum radiated power is ______ of peak visual transmitter power. A. 10% B. 30% C. 20% D. 40%

Last Answer : C. 20%

An invitation from the primary to a secondary to transmit a message. A. Retransmission B. Selection C. Reuse D. Polling

Description : An invitation from the primary to a secondary to transmit a message. A. Retransmission B. Selection C. Reuse D. Polling

Last Answer : D. Polling

The transmitter technique adopted to reduce the noise effect of the preceding question is called A. noise masking B. anitnoise C. noise killing D. preemphasis

Description : The transmitter technique adopted to reduce the noise effect of the preceding question is called A. noise masking B. anitnoise C. noise killing D. preemphasis

Last Answer : D. preemphasis

What is the channel bandwidth of a standard analogue telephone system? A. 300-500 Hz B. 1200 kHz C. 100-300 Hz D. 300-3400 Hz

Description : What is the channel bandwidth of a standard analogue telephone system? A. 300-500 Hz B. 1200 kHz C. 100-300 Hz D. 300-3400 Hz

Last Answer : D. 300-3400 Hz

Binary communications systems are better because A. they can interface directly with the analog telephone network B. the components are simpler, less costly, and more reliable C. people think better in binary D. interstate calls are less costly

Description : Binary communications systems are better because A. they can interface directly with the analog telephone network B. the components are simpler, less costly, and more reliable C. people think better in binary D. interstate calls are less costly

Last Answer : B. the components are simpler, less costly, and more reliable

What region around a broadcasting transmitter in which satisfactory reception of broadcasting signal is not obtained? A. Fringe area B. Primary are C. Secondary area D. Tertiary area

Description : What region around a broadcasting transmitter in which satisfactory reception of broadcasting signal is not obtained? A. Fringe area B. Primary are C. Secondary area D. Tertiary area

Last Answer : A. Fringe area

How far is the visual carrier from the lowest frequency in the spectrum of a monochrome TV broadcast channel following the NTSC standard? A. 1.5 MHz B. 1.25 MHz C. 4.5 MHz D. 0.25 MHz

Description : How far is the visual carrier from the lowest frequency in the spectrum of a monochrome TV broadcast channel following the NTSC standard? A. 1.5 MHz B. 1.25 MHz C. 4.5 MHz D. 0.25 MHz

Last Answer : B. 1.25 MHz

The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at

Description : The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at 80% is A) 50 W B) 66 W C) 68 W D) 70 W 

Last Answer : The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at 80% is 66 W

If the radiated power of AM transmitter is 10 KW, the power in the carrier for modulation index of 0.6 is...

Description : If the radiated power of AM transmitter is 10 KW, the power in the carrier for modulation index of 0.6 is nearly:  (1) 8.24 KW (2) 9.26 KW (3) 8.47 KW (4) 9.6 KW

Last Answer : If the radiated power of AM transmitter is 10 KW, the power in the carrier for modulation index of 0.6 is nearly: 8.47 KW.

What is antenna bandwidth? A. Antenna length divided by the number of elements B. The angle between the half-power radiation points C. The angle formed between two imaginary lines drawn through D. The frequency range over which an antenna can be expected to operate satisfactorily

Description : What is antenna bandwidth? A. Antenna length divided by the number of elements B. The angle between the half-power radiation points C. The angle formed between two imaginary lines drawn through D. The frequency range over which an antenna can be expected to operate satisfactorily

Last Answer : D. The frequency range over which an antenna can be expected to operate satisfactorily

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured C. A random voltage across the resistor does not exist D. All formula referring to random noise are applicable only to the value of such noise.

Description : Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured ... exist D. All formula referring to random noise are applicable only to the value of such noise.

Last Answer : C. A random voltage across the resistor does not exist

What is meant by the term antenna bandwidth A. Antenna length divided by the number of elements. B. The angle between the half-power radiation points C. The frequency range over which and antenna can be expected to perform well D. The angle formed between two imaginary line drawn through the ends of the elements

Description : What is meant by the term antenna bandwidth A. Antenna length divided by the number of elements. B. The angle between the half-power radiation points C. The frequency range over which and antenna ... perform well D. The angle formed between two imaginary line drawn through the ends of the elements

Last Answer : C. The frequency range over which and antenna can be expected to perform well

What do you call the service area of a standard AM broadcast where fading is allowed but not objectionable co-channel interference? A. Experimental B. Secondary C. Tertiary D. Primary

Description : What do you call the service area of a standard AM broadcast where fading is allowed but not objectionable co-channel interference? A. Experimental B. Secondary C. Tertiary D. Primary

Last Answer : B. Secondary

The product of antenna input power and the antenna power gain expressed in kW is called __. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Description : The product of antenna input power and the antenna power gain expressed in kW is called __. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Last Answer : A. Effective Radiated Power (ERP)

The advantage of periscope antenna in microwave A. Minimize interference to and from other neighboring stations B. Shorten waveguide link C. Reduce tower height D. All of these

Description : The advantage of periscope antenna in microwave A. Minimize interference to and from other neighboring stations B. Shorten waveguide link C. Reduce tower height D. All of these

Last Answer : B. Shorten waveguide link

How do you transmit through multiplexing, a thousand of voice channel information over a single fiber optic using on e wavelength? A. Polar division B. Time division C. Fiber division D. Frequency division

Description : How do you transmit through multiplexing, a thousand of voice channel information over a single fiber optic using on e wavelength? A. Polar division B. Time division C. Fiber division D. Frequency division

Last Answer : B. Time division

In AM, the carrier carries ____________ intelligence.A. no B. difference C. distorted D. same

Description : In AM, the carrier carries ____________ intelligence. A. no B. difference C. distorted D. same

Last Answer : A. no

The final amplifier of either FM or AM transmitter operates as A. Class B B. Class C C. Class A D. Class D

Description : The final amplifier of either FM or AM transmitter operates as A. Class B B. Class C C. Class A D. Class D

Last Answer : B. Class C

The synchronous modems are more costly than the asynchronous modems because a. they produce large volume of data b. they contain clock recovery circuits c. they transmit the data with stop and start bits d. they operate with a larger bandwidth e. none of above

Description : The synchronous modems are more costly than the asynchronous modems because a. they produce large volume of data b. they contain clock recovery circuits c. they transmit the data with stop and start bits d. they operate with a larger bandwidth e. none of above

Last Answer : they contain clock recovery circuits

The total noise power present in a 1-Hz bandwidth . A. Noise density B. Noise figure C. Noise limit D. Noise intensity

Description : The total noise power present in a 1-Hz bandwidth . A. Noise density B. Noise figure C. Noise limit D. Noise intensity

Last Answer : A. Noise density

If bandwidth is doubled, the signal power is _________. A. not changed B. quadrupled C. tripled D. doubled

Description : If bandwidth is doubled, the signal power is _________. A. not changed B. quadrupled C. tripled D. doubled

Last Answer : A. not changed

What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Description : What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Last Answer : B. 3853 Hz

lobes between end of the love at which the relative power is one half (-3dB) its value from the peak of the lobe. A. Bandwidth B. Wavelength C. Radiation D. Beamwidth

Description : Width measured in degrees of a major lobes between end of the love at which the relative power is one half (-3dB) its value from the peak of the lobe. A. Bandwidth B. Wavelength C. Radiation D. Beamwidth

Last Answer : D. Beamwidth

The main benefit of light-wave communications over microwaves or any other communications media is a. Lower cost b. Better security c. Wider bandwidth d. Freedom from interference

Description : The main benefit of light-wave communications over microwaves or any other communications media is a. Lower cost b. Better security c. Wider bandwidth d. Freedom from interference

Last Answer : c. Wider bandwidth

The square of the thermal noise voltage generated by a resistor is proportional to A. its resistance B. its temperature C. the bandwidth over which it is measured D. All of the above

Description : The square of the thermal noise voltage generated by a resistor is proportional to A. its resistance B. its temperature C. the bandwidth over which it is measured D. All of the above

Last Answer : D. All of the above

At 17˚ C, the noise voltage generated by 5kΩ resistor, operating over a bandwidth of 20KHz is A. 1.3 nV B. 1.3 µV C. 1.3 pV D. 1.3 mV

Description : At 17˚ C, the noise voltage generated by 5kΩ resistor, operating over a bandwidth of 20KHz is A. 1.3 nV B. 1.3 µV C. 1.3 pV D. 1.3 mV

Last Answer : B. 1.3 µV

Ho w many times bigger does the bandwidth of a fiber optic multimode have over a cable? A. 50 times bigger B. 100 times bigger C. 10 times bigger D. 5 times bigger

Description : Ho w many times bigger does the bandwidth of a fiber optic multimode have over a cable? A. 50 times bigger B. 100 times bigger C. 10 times bigger D. 5 times bigger

Last Answer : B. 100 times bigger

An antenna “efficiency” is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x 100% C. Efficiency = (effective radiated power / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Description : An antenna efficiency is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x ... / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Last Answer : D. Efficiency = (radiation resistance / total resistance) x 100%