What is a dummy antenna? A. One which is used as a reference for gain measurements B. And antenna used for hand-held radio C. An non-directional transmitting antenna D. A non-radiating load for a transmitter used for testing

What is a dummy antenna?
A. One which is used as a reference for gain measurements
B. And antenna used for hand-held radio
C. An non-directional transmitting antenna
D. A non-radiating load for a transmitter used for testing
by

1 Answer

Answer :

D. A non-radiating load for a transmitter used for testing
by

Related questions

It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Description : It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Last Answer : A. when comparing the gains of directional antennas

When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern hemisphere) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Description : When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern ... ) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Last Answer : A. When comparing the gains of directional antennas

In testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Void antenna B. Dummy antenna C. Hertzian antenna D. Isotropic antenna

Description : In testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Void antenna B. Dummy antenna C. Hertzian antenna D. Isotropic antenna

Last Answer : B. Dummy antenna

When testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Dummy antenna B. Hertzian antenna C. None of these D. Void antenna

Description : When testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Dummy antenna B. Hertzian antenna C. None of these D. Void antenna

Last Answer : A. Dummy antenna

One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Description : One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Last Answer : C. Use of dummy antenna

Stacking elements in a transmitting antenna system A. increases the field strength at the receiving antenna B. increases the directivity of the transmitter antenna C. decrease the size of the lobe in the radiation pattern D. both A and B

Description : Stacking elements in a transmitting antenna system A. increases the field strength at the receiving antenna B. increases the directivity of the transmitter antenna C. decrease the size of the lobe in the radiation pattern D. both A and B

Last Answer : D. both A and B

Which of the following antennas is used for testing and adjusting a transmitter for proper modulation, amplifier operation and frequency accuracy? A. Elementary B. Real C. Isotropic D. Dummy

Description : Which of the following antennas is used for testing and adjusting a transmitter for proper modulation, amplifier operation and frequency accuracy? A. Elementary B. Real C. Isotropic D. Dummy

Last Answer : D. Dummy

Unity gain antenna A. Isotropic B. Rhombic C. Half-wave dipole D. Dummy

Description : Unity gain antenna A. Isotropic B. Rhombic C. Half-wave dipole D. Dummy

Last Answer : A. Isotropic

When adjusting an RF filter on a transmitter using a dummy load, how much watts dissipation should it stand to test a 150 watts transmitter? A. 75 watts B. 300 watts C. 50 watts D. 150 watts

Description : When adjusting an RF filter on a transmitter using a dummy load, how much watts dissipation should it stand to test a 150 watts transmitter? A. 75 watts B. 300 watts C. 50 watts D. 150 watts

Last Answer : D. 150 watts

For a space wave transmission, the radio horizon distance of a transmitting antenna with a height of 100 meters is approximately:A. 10 km B. 40 km C. 100 km D. 400 km

Description : For a space wave transmission, the radio horizon distance of a transmitting antenna with a height of 100 meters is approximately: A. 10 km B. 40 km C. 100 km D. 400 km

Last Answer : B. 40 km

The purpose of stacking elements on an antenna. A. Sharper directional pattern B. increased gain C. Improved bandpass D. All of these

Description : The purpose of stacking elements on an antenna. A. Sharper directional pattern B. increased gain C. Improved bandpass D. All of these

Last Answer : D. All of these

A theoretical reference antenna that provides a comparison for antenna measurements. A. Marconi antenna B. Isotropic radiator C. Yagi-Uda array D. Whip antenna

Description : A theoretical reference antenna that provides a comparison for antenna measurements. A. Marconi antenna B. Isotropic radiator C. Yagi-Uda array D. Whip antenna

Last Answer : B. Isotropic radiator

Radio wave concentration in the direction of the signal emitted by a directional antenna. A. Back lobe radiation B. Side lobe radiation C. Major lobe radiation D. Transmitted signal

Description : Radio wave concentration in the direction of the signal emitted by a directional antenna. A. Back lobe radiation B. Side lobe radiation C. Major lobe radiation D. Transmitted signal

Last Answer : C. Major lobe radiation

If an antenna has a gain of 3 dB, it increases the output of the transmitter by A. 10,000 times B. 1000 times C. 100 times D. 1 million times

Description : If an antenna has a gain of 3 dB, it increases the output of the transmitter by A. 10,000 times B. 1000 times C. 100 times D. 1 million times

Last Answer : B. 1000 times

What is the effective radiated power of a repeater with 200 watts transmitter power output, 4 dB feline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 317 W B. 2000 W C. 126 W D. 260 W

Description : What is the effective radiated power of a repeater with 200 watts transmitter power output, 4 dB feline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 317 W B. 2000 W C. 126 W D. 260 W

Last Answer : A. 317 W

What is the effective radiated power of a repeater with 120 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 601 W B. 240 W C. 60 W D. 379 W

Description : What is the effective radiated power of a repeater with 120 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 601 W B. 240 W C. 60 W D. 379 W

Last Answer : C. 60 W

What is the effective radiated power of a repeater with 100 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 800 W B. 126 W C. 12.5 W D. 1260 W

Description : What is the effective radiated power of a repeater with 100 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 800 W B. 126 W C. 12.5 W D. 1260 W

Last Answer : B. 126 W

What is the effective radiated power of a repeater with 75 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 37.6 W B. 237 W C. 150 W D. 23.7 W

Description : What is the effective radiated power of a repeater with 75 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 37.6 W B. 237 W C. 150 W D. 23.7 W

Last Answer : A. 37.6 W

What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Description : What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Last Answer : D. 150 W

What is the effective radiated power of a repeater with 50 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 7 dB antenna gain? A. 300 W B. 315 W C. 31.5 W D. 69.9 W

Description : What is the effective radiated power of a repeater with 50 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 7 dB antenna gain? A. 300 W B. 315 W C. 31.5 W D. 69.9 W

Last Answer : C. 31.5 W

What is the effective radiated power of a repeater with 50 watts transmitter power output \, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 6 dB antenna gain? A. 158 W B. 39.7 W C. 251 W D. 69.9 W

Description : What is the effective radiated power of a repeater with 50 watts transmitter power output \, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 6 dB antenna gain? A. 158 W B. 39.7 W C. 251 W D. 69.9 W

Last Answer : B. 39.7 W

The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Description : The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Last Answer : B. Effective Isotropic Radiated Power (EIRP)

A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Description : A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Last Answer : C. 49

Determine the effective radiated power of 20 kW TV broadcast transmitter whose antenna has a field gain of 2. A. 40 kW B. 80,000 watts C. 40,000 watts D. 8,000 watts

Description : Determine the effective radiated power of 20 kW TV broadcast transmitter whose antenna has a field gain of 2. A. 40 kW B. 80,000 watts C. 40,000 watts D. 8,000 watts

Last Answer : B. 80,000 watts

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Description : ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Last Answer : C. gain of the antenna

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Description : Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Last Answer : D. Spark emission

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Last Answer : C. Carrier power

In the case if Marconi antenna, the actual length if the radiating element is A. one-half wavelength B. one-quarter wavelength C. one wavelength D. one-eight wavelength

Description : In the case if Marconi antenna, the actual length if the radiating element is A. one-half wavelength B. one-quarter wavelength C. one wavelength D. one-eight wavelength

Last Answer : B. one-quarter wavelength

ECE Board Exam March 1996 The standard reference antenna for the directive gain is ___________A. elementary doublet B. isotropic antenna C. half-wave dipole D. infinitesimal dipole

Description : ECE Board Exam March 1996 The standard reference antenna for the directive gain is ___________. A. elementary doublet B. isotropic antenna C. half-wave dipole D. infinitesimal dipole

Last Answer : B. isotropic antenna

It is the ratio of the power density radiated in a particular direction to the power density radiated to the same point by a reference antenna, assuming both antennas are radiating the same amount of power

Description : It is the ratio of the power density radiated in a particular direction to the power density radiated to the same point by a reference antenna, assuming both antennas are radiating the same amount of power

Last Answer : directive gain

A receiver is located 64 km from a space wave transmitting antenna that is 100 meters high. Find the required height of the receiving antenna. A. 36 meters high B. 64 meters high C. 100 meters high D. 182.25 meters high

Description : A receiver is located 64 km from a space wave transmitting antenna that is 100 meters high. Find the required height of the receiving antenna. A. 36 meters high B. 64 meters high C. 100 meters high D. 182.25 meters high

Last Answer : A. 36 meters high

If a transmitting antenna is 100 meters high and a separate receiving antenna is 64 meters high, what is the maximum space wave communication distance possible between them? A. 18 km B. 72 km C. 164 km D. 656 km

Description : If a transmitting antenna is 100 meters high and a separate receiving antenna is 64 meters high, what is the maximum space wave communication distance possible between them? A. 18 km B. 72 km C. 164 km D. 656 km

Last Answer : B. 72 km

A disadvantage of using a trap antenna. A. It will radiate harmonics B. It can only be used for single-bad operation C. It is too sharply directional at lower frequencies D. It must be neutralized

Description : A disadvantage of using a trap antenna. A. It will radiate harmonics B. It can only be used for single-bad operation C. It is too sharply directional at lower frequencies D. It must be neutralized

Last Answer : A. It will radiate harmonics

______ is an antenna array which is highly directional at right angles to the plane of the array? A. Broadside array B. End-fire array C. Turnstile array D. Log-periodic array

Description : ______ is an antenna array which is highly directional at right angles to the plane of the array? A. Broadside array B. End-fire array C. Turnstile array D. Log-periodic array

Last Answer : A. Broadside array

_____ is an antenna with a number of half-wave antenna on it. A. Antenna array B. Tower C. Omni-directional D. Rhombic

Description : _____ is an antenna with a number of half-wave antenna on it. A. Antenna array B. Tower C. Omni-directional D. Rhombic

Last Answer : A. Antenna array

The polarization of a discone antenna is _____. A. Horizontal B. Vertical C. Omni D. Directional

Description : The polarization of a discone antenna is _____. A. Horizontal B. Vertical C. Omni D. Directional

Last Answer : B. Vertical

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

What would happen if you plugged an FM transmitter into a radio's headphone jack and set the radio to the transmitter's transmitting frequency?

Description : What would happen if you plugged an FM transmitter into a radio's headphone jack and set the radio to the transmitter's transmitting frequency?

Last Answer : You would get a positive feedback loop, probably resulting in an audible tone. The amplitude would be limited by the transmitter’s modulation limiter, so all you’d have is a very ordinary oscillator.

What is a selective fading effect? A. A fading effect caused by small changes in beam heading at the receiving station. B. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station. C. A fading effect caused by large changes in the height of the ionosphere, as experienced at the receiving station D. A fading effect caused by time differences between the receiving and transmitting stations.

Description : What is a selective fading effect? A. A fading effect caused by small changes in beam heading at the receiving station. B. A fading effect caused by phase differences between radio wave ... station D. A fading effect caused by time differences between the receiving and transmitting stations.

Last Answer : B. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station.

What is the major cause of selective fading? A. Small changes in the beam heading at the receiving station. B. Large changes in the height of the ionosphere, as experience at the receiving station. C. Time differences between the receiving and transmitting stations. D. Phase differences between radio wave components of the same transmission, as experienced at the receiving station.

Description : What is the major cause of selective fading? A. Small changes in the beam heading at the receiving station. B. Large changes in the height of the ionosphere, as experience at the ... Phase differences between radio wave components of the same transmission, as experienced at the receiving station.

Last Answer : D. Phase differences between radio wave components of the same transmission, as experienced at the receiving station.

The conversion of digital signal into analog for purposes of transmitting into the telephone line is done through ______. A. ISDN B. Radio C. RS232C D. Modem

Description : The conversion of digital signal into analog for purposes of transmitting into the telephone line is done through ______. A. ISDN B. Radio C. RS232C D. Modem

Last Answer : D. Modem

Refers to an effect of selective fading. A. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station. B. A fading effect caused by small changes in beam heading at the receiving station. C. A fading effect caused by the time differences between the receiving and transmitting stations. D. A fading effect caused by large changes in the height of the ionosphere, as experienced at the receiving station.

Description : Refers to an effect of selective fading. A. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station. B. A fading ... caused by large changes in the height of the ionosphere, as experienced at the receiving station.

Last Answer : A. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station.

Production of radiation by a radio transmitting station A. Monitoring B. Emission C. Radiation D. Transmission

Description : Production of radiation by a radio transmitting station A. Monitoring B. Emission C. Radiation D. Transmission

Last Answer : B. Emission

ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Description : ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Last Answer : B. Communications satellite

How does spatial isolation technique in satellite communications avoid interference? A. Use of different polarity antennas B. Use of different types of antennas C. Employment of highly directional spot-beam antennas D. Use of low gain antennas

Description : How does spatial isolation technique in satellite communications avoid interference? A. Use of different polarity antennas B. Use of different types of antennas C. Employment of highly directional spot-beam antennas D. Use of low gain antennas

Last Answer : C. Employment of highly directional spot-beam antennas

In radio-communication, the signals emitted by transmitting antenna are reflected on – (1) stratosphere (2) ozonosphere (3) ionosphere (4) troposphere

Description : In radio-communication, the signals emitted by transmitting antenna are reflected on – (1) stratosphere (2) ozonosphere (3) ionosphere (4) troposphere

Last Answer : (3) ionosphere Explanation: The lower atmosphere is more or less transparent to radio waves. However, the ionosphere reflects back the radio waves. Thus, a signal emitted by an antenna from a ... on the surface of Earth in the following two ways: ground wave propagation and sky wave propagation.