It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

It is useful to refer to an isotropic radiator.
A. when comparing the gains of directional antennas
B. when testing a transmission line for standing wave ratio
C. when (in the northern hemisphere) directing the transmission
D. when using a dummy load to tune a transmitter
by

1 Answer

Answer :

A. when comparing the gains of directional antennas
by

Related questions

When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern hemisphere) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Description : When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern ... ) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Last Answer : A. When comparing the gains of directional antennas

Which of the following antennas is used for testing and adjusting a transmitter for proper modulation, amplifier operation and frequency accuracy? A. Elementary B. Real C. Isotropic D. Dummy

Description : Which of the following antennas is used for testing and adjusting a transmitter for proper modulation, amplifier operation and frequency accuracy? A. Elementary B. Real C. Isotropic D. Dummy

Last Answer : D. Dummy

What is a dummy antenna? A. One which is used as a reference for gain measurements B. And antenna used for hand-held radio C. An non-directional transmitting antenna D. A non-radiating load for a transmitter used for testing

Description : What is a dummy antenna? A. One which is used as a reference for gain measurements B. And antenna used for hand-held radio C. An non-directional transmitting antenna D. A non-radiating load for a transmitter used for testing

Last Answer : D. A non-radiating load for a transmitter used for testing

An isotropic radiator is A. in the northern hemisphere B. an antenna high enough in the air C. an antenna whose directive pattern is substantially incredible D. a hypothetical, omnidirectional antenna

Description : An isotropic radiator is A. in the northern hemisphere B. an antenna high enough in the air C. an antenna whose directive pattern is substantially incredible D. a hypothetical, omnidirectional antenna

Last Answer : D. a hypothetical, omnidirectional antenna

In testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Void antenna B. Dummy antenna C. Hertzian antenna D. Isotropic antenna

Description : In testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Void antenna B. Dummy antenna C. Hertzian antenna D. Isotropic antenna

Last Answer : B. Dummy antenna

One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Description : One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Last Answer : C. Use of dummy antenna

The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Description : The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Last Answer : B. Effective Isotropic Radiated Power (EIRP)

Unity gain antenna A. Isotropic B. Rhombic C. Half-wave dipole D. Dummy

Description : Unity gain antenna A. Isotropic B. Rhombic C. Half-wave dipole D. Dummy

Last Answer : A. Isotropic

Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Description : Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Last Answer : D. The standing wave ratio is one.

The standing wave ratio is equal to ________ if the load is properly matched with the transmission line. A. 1 B. 50 C. 10 D. 2

Description : The standing wave ratio is equal to ________ if the load is properly matched with the transmission line. A. 1 B. 50 C. 10 D. 2

Last Answer : A. 1

When adjusting an RF filter on a transmitter using a dummy load, how much watts dissipation should it stand to test a 150 watts transmitter? A. 75 watts B. 300 watts C. 50 watts D. 150 watts

Description : When adjusting an RF filter on a transmitter using a dummy load, how much watts dissipation should it stand to test a 150 watts transmitter? A. 75 watts B. 300 watts C. 50 watts D. 150 watts

Last Answer : D. 150 watts

When testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Dummy antenna B. Hertzian antenna C. None of these D. Void antenna

Description : When testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Dummy antenna B. Hertzian antenna C. None of these D. Void antenna

Last Answer : A. Dummy antenna

Determine the standing wave ratio of a 300-Ω line whose load is 400+j150 Ω. A. 3.55 B. 1.67 C. 5.53 D. 3.35

Description : Determine the standing wave ratio of a 300-Ω line whose load is 400+j150 Ω. A. 3.55 B. 1.67 C. 5.53 D. 3.35

Last Answer : B. 1.67

Which of the following antennas require good grounding? A. Yagi antenna B. Hertz antenna C. Marconi antenna D. Isotropic antenna

Description : Which of the following antennas require good grounding? A. Yagi antenna B. Hertz antenna C. Marconi antenna D. Isotropic antenna

Last Answer : C. Marconi antenna

What is the gain of an antenna over a half-wavelength dipole when it has 6 dB gain over an isotropic radiator? A. 6.0 dB B. 8.1 dB C. 3.9 dB D. 10.0 dB

Description : What is the gain of an antenna over a half-wavelength dipole when it has 6 dB gain over an isotropic radiator? A. 6.0 dB B. 8.1 dB C. 3.9 dB D. 10.0 dB

Last Answer : C. 3.9 dB

A theoretical reference antenna that provides a comparison for antenna measurements. A. Marconi antenna B. Isotropic radiator C. Yagi-Uda array D. Whip antenna

Description : A theoretical reference antenna that provides a comparison for antenna measurements. A. Marconi antenna B. Isotropic radiator C. Yagi-Uda array D. Whip antenna

Last Answer : B. Isotropic radiator

The directivity pattern of an isotropic radiator is A. a figure-8 B. a sphere C. a unidirectional cardioid D. a parabola

Description : The directivity pattern of an isotropic radiator is A. a figure-8 B. a sphere C. a unidirectional cardioid D. a parabola

Last Answer : B. a sphere

How does spatial isolation technique in satellite communications avoid interference? A. Use of different polarity antennas B. Use of different types of antennas C. Employment of highly directional spot-beam antennas D. Use of low gain antennas

Description : How does spatial isolation technique in satellite communications avoid interference? A. Use of different polarity antennas B. Use of different types of antennas C. Employment of highly directional spot-beam antennas D. Use of low gain antennas

Last Answer : C. Employment of highly directional spot-beam antennas

Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Description : Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Last Answer : D. load connected to the output end of a transmission line

The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.

Description : The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.

Last Answer : The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be 4.

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Description : Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Last Answer : B. The location of the antenna with respect to nearby objects

ECE Board Exam March 1996 When the transmitting and receiving antennas are in line-of-sight of each other, the mode of propagation is ________ wave. A. space or direct B. ground C. surface D. sky

Description : ECE Board Exam March 1996 When the transmitting and receiving antennas are in line-of-sight of each other, the mode of propagation is ________ wave. A. space or direct B. ground C. surface D. sky

Last Answer : A. space or direct

For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Description : For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Last Answer : B. Near the center of the vertical radiator

What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Description : What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Last Answer : A. Velocity factor

A component that samples the microwave signal travelling in one direction down to the transmission line A. Isolator B. Combiner C. Directional coupler D. Attenuator

Description : A component that samples the microwave signal travelling in one direction down to the transmission line A. Isolator B. Combiner C. Directional coupler D. Attenuator

Last Answer : C. Directional coupler

Best choice of transmission line component to couple a coaxial line to a parallel-wire line A. Shorting B. Balun C. Slotted line D. Directional coupler

Description : Best choice of transmission line component to couple a coaxial line to a parallel-wire line A. Shorting B. Balun C. Slotted line D. Directional coupler

Last Answer : B. Balun

To couple a coaxial line to parallel line, it is better to use a ______. A. Slotted line B. Quarter-wave transformer C. Directional Coupler D. Balun

Description : To couple a coaxial line to parallel line, it is better to use a ______. A. Slotted line B. Quarter-wave transformer C. Directional Coupler D. Balun

Last Answer : D. Balun

To connect coaxial line to a parallel-wire _________ is the best to use. A. directional coupler B. quarter-wave transformer C. balun D. slotted line

Description : To connect coaxial line to a parallel-wire _________ is the best to use. A. directional coupler B. quarter-wave transformer C. balun D. slotted line

Last Answer : C. balun

An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Description : An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Last Answer : B. Either A or C

Space diversity transmission means transmitting and receiving on _______. A. Two or more antennas operating on two different frequencies B. Two or more identical frequencies C. Two or more antennas operating on the same frequency D. Two or more different frequency

Description : Space diversity transmission means transmitting and receiving on _______. A. Two or more antennas operating on two different frequencies B. Two or more identical frequencies C. Two or more antennas operating on the same frequency D. Two or more different frequency

Last Answer : C. Two or more antennas operating on the same frequency

Space diversity transmission means transmitting and receiving on A. two or more antennas operating on two different frequencies B. two or more identical frequencies C. two or more different frequencies D. two or more antennas operating on the same frequencies

Description : Space diversity transmission means transmitting and receiving on A. two or more antennas operating on two different frequencies B. two or more identical frequencies C. two or more different frequencies D. two or more antennas operating on the same frequencies

Last Answer : D. two or more antennas operating on the same frequencies

In what region of the world is sporadic-E most prevalent? A. The equatorial regions B. The northern hemisphere C. The arctic regions D. The polar regions

Description : In what region of the world is sporadic-E most prevalent? A. The equatorial regions B. The northern hemisphere C. The arctic regions D. The polar regions

Last Answer : A. The equatorial regions

An antenna with unity gain A. Rhombic B. Half-wave dipole C. Isotropic D. Whip

Description : An antenna with unity gain A. Rhombic B. Half-wave dipole C. Isotropic D. Whip

Last Answer : C. Isotropic

ECE Board Exam March 1996 The standard reference antenna for the directive gain is ___________A. elementary doublet B. isotropic antenna C. half-wave dipole D. infinitesimal dipole

Description : ECE Board Exam March 1996 The standard reference antenna for the directive gain is ___________. A. elementary doublet B. isotropic antenna C. half-wave dipole D. infinitesimal dipole

Last Answer : B. isotropic antenna

If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Description : If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Last Answer : D. 6 watts

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Last Answer : C. Carrier power

A device that radiates electromagnetic energy and or intercepts electromagnetic radation. A. Antenna B. Transmitter C. Transmission line D. Transceiver

Description : A device that radiates electromagnetic energy and or intercepts electromagnetic radation. A. Antenna B. Transmitter C. Transmission line D. Transceiver

Last Answer : A. Antenna

What is the meaning of the term “velocity factor” of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial cable. C. The velocity of the wave on the transmission line multiplied by the velocity of light in a vacuum. D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Description : What is the meaning of the term velocity factor of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of light in vacuum C. The ratio of the characteristic impedance of the line to the terminating impedance D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Description : What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

For transmission line, the incident voltage Ei = 6V, and Er = 3V. Calculate: (1) Reflection coefficient (2) Standing wave ratio

Description : For transmission line, the incident voltage Ei = 6V, and Er = 3V. Calculate: (1) Reflection coefficient (2) Standing wave ratio

Last Answer : (1)Reflection coefficient  (2) Standing wave ratio (1)Reflection coefficient Reflection coefficient R=Er/Ei  =3/6  R=0.5 (2) Standing wave ratio SWR=Ei+Er/Ei-Er  =6+3/6-3  SWR =3

_____ is an antenna with a number of half-wave antenna on it. A. Antenna array B. Tower C. Omni-directional D. Rhombic

Description : _____ is an antenna with a number of half-wave antenna on it. A. Antenna array B. Tower C. Omni-directional D. Rhombic

Last Answer : A. Antenna array

Radio wave concentration in the direction of the signal emitted by a directional antenna. A. Back lobe radiation B. Side lobe radiation C. Major lobe radiation D. Transmitted signal

Description : Radio wave concentration in the direction of the signal emitted by a directional antenna. A. Back lobe radiation B. Side lobe radiation C. Major lobe radiation D. Transmitted signal

Last Answer : C. Major lobe radiation

An antenna “efficiency” is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x 100% C. Efficiency = (effective radiated power / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Description : An antenna efficiency is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x ... / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Last Answer : D. Efficiency = (radiation resistance / total resistance) x 100%

One of the following is not a useful quantity for comparing the noise performance receivers. A. Input noise voltage B. Equivalent noise resistance C. Noise temperature D. Noise figure.

Description : One of the following is not a useful quantity for comparing the noise performance receivers. A. Input noise voltage B. Equivalent noise resistance C. Noise temperature D. Noise figure.

Last Answer : A. Input noise voltage

Find the standing wave ratio, when a load impedance of 250 ohm is connected to a 75 ohm line. a) 0.3 b) 75 c) 250 d) 3.33

Description : Find the standing wave ratio, when a load impedance of 250 ohm is connected to a 75 ohm line. a) 0.3 b) 75 c) 250 d) 3.33

Last Answer : d) 3.33

Explain isotropic radiator with neat sketch.

Description : Explain isotropic radiator with neat sketch. 

Last Answer : An isotropic radiator is a point source that radiates equally in all the directions. It is a hypothetical antenna used as a reference to describe real antenna. The radiation is represented by a sphere with center coincides with location of isotropic radiator.