The input terminal impedance at the center of a folded dipole antenna is A. 72 Ω B. 300 Ω C. 50 Ω D. 73 Ω

The input terminal impedance at the center of a folded dipole antenna is
A. 72 Ω
B. 300 Ω
C. 50 Ω
D. 73 Ω
by

1 Answer

Answer :

B. 300 Ω
by

Related questions

What is the input terminal impedance at the center if a folded dipole antenna? A. 300 ohms B. 72 ohms C. 50 ohms D. 450 ohms

Description : What is the input terminal impedance at the center if a folded dipole antenna? A. 300 ohms B. 72 ohms C. 50 ohms D. 450 ohms

Last Answer : A. 300 ohms

What is the end impedance of a half-wave dipole? A. 73 Ω B. 72 Ω C. 250 Ω D. 2500 Ω

Description : What is the end impedance of a half-wave dipole? A. 73 Ω B. 72 Ω C. 250 Ω D. 2500 Ω

Last Answer : D. 2500 Ω

What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150Ω D. 2 Ω

Description : What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150 Ω D. 2 Ω

Last Answer : C. 150 Ω

What is the characteristic impedance of a single wire with a diameter d= 0.25 mm placed at the center between grounded parallel planes separated by 1 mm apart. The wire is held by a material with a velocity factor of 0.75. A. 85 Ω B. 63 Ω C. 50 Ω D. 75 Ω

Description : What is the characteristic impedance of a single wire with a diameter d= 0.25 mm placed at the center between grounded parallel planes separated by 1 mm apart. The wire is held by a material with a velocity factor of 0.75. A. 85 Ω B. 63 Ω C. 50 Ω D. 75 Ω

Last Answer : D. 75 Ω

Which antenna is not a wideband? A. Discone B. Folded dipole C. Helical D. Marconi

Description : Which antenna is not a wideband? A. Discone B. Folded dipole C. Helical D. Marconi

Last Answer : D. Marconi

Which is a non-resonant antenna? A. Rhombic antenna B. Folded dipole C. End-fire array D. Yagi-Uda antenna

Description : Which is a non-resonant antenna? A. Rhombic antenna B. Folded dipole C. End-fire array D. Yagi-Uda antenna

Last Answer : A. Rhombic antenna

Which is the non-resonant antenna? A. Broadside Antenna B. Folded Dipole C. Rhombic antenna D. End fire array

Description : Which is the non-resonant antenna? A. Broadside Antenna B. Folded Dipole C. Rhombic antenna D. End fire array

Last Answer : C. Rhombic antenna

A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Description : A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Last Answer : D. 112 Ω

In horizontal-dipole antenna, the polarization is A. in the vertical direction B. in the horizontal direction C. circular D. measured at the center of the antenna

Description : In horizontal-dipole antenna, the polarization is A. in the vertical direction B. in the horizontal direction C. circular D. measured at the center of the antenna

Last Answer : B. in the horizontal direction

Known as the technique for adding a series inductor at or near the center of an antenna element in order to cancel the capacitive reactance of an antenna. A. Dipole B. Center loading C. Reflector D. loading coil

Description : Known as the technique for adding a series inductor at or near the center of an antenna element in order to cancel the capacitive reactance of an antenna. A. Dipole B. Center loading C. Reflector D. loading coil

Last Answer : D. loading coil

Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Description : Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Last Answer : A. Center of the antenna

A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW. What is the gain in dB, obtained by the use if the reflector. (Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Description : A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW ... Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Last Answer : B. 2.6

A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 kW. What is the gain in dB obtain by the use of the reflector ? ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Description : A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 ... ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Last Answer : D. 2.6

Most mobile satellite array uses ___________ in transforming 50 to 150 Ω impedance. A. stub B. balun C. quarter-wavelength transformer D. microstrip tapers.

Description : Most mobile satellite array uses ___________ in transforming 50 to 150 Ω impedance. A. stub B. balun C. quarter-wavelength transformer D. microstrip tapers.

Last Answer : C. quarter-wavelength transformer

What is the impedance of a balance 4-wire with a diameter of 0.25 cm and spaced 2.5 cm apart using an insulator with a dielectric constant of 2.56? A. 100Ω B. 65Ω C. 75 Ω D. 50 Ω

Description : What is the impedance of a balance 4-wire with a diameter of 0.25 cm and spaced 2.5 cm apart using an insulator with a dielectric constant of 2.56? A. 100Ω B. 65Ω C. 75 Ω D. 50 Ω

Last Answer : A. 100Ω

A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Description : A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Last Answer : B. 174K

A transmitted signal 5 meters in wavelength is received by an antenna coil having a 50-Ω resistance and a 0.01 H inductance. What is the capacitance of the tuner shunting the antenna coil at this point? A. 0.704 fF B. 0.704 μF C. 0.704 nF D. 0.704 mF

Description : A transmitted signal 5 meters in wavelength is received by an antenna coil having a 50-Ω resistance and a 0.01 H inductance. What is the capacitance of the tuner shunting the antenna coil at this point? A. 0.704 fF B. 0.704 μF C. 0.704 nF D. 0.704 mF

Last Answer : A. 0.704 fF

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

Indicate the antenna thatisnotwideband: a. Discone b. Folded Dipole c. Helical d. Marconi

Description : Indicate the antenna thatisnotwideband: a. Discone b. Folded Dipole c. Helical d. Marconi

Last Answer : d. Marconi

One ofthe followingconsistsof nonresonant antennas: a.The rhombic antenna b. The folded dipole c. The end-fire array d. The broadside array

Description : One ofthe followingconsistsof nonresonant antennas: a.The rhombic antenna b. The folded dipole c. The end-fire array d. The broadside array

Last Answer : a.The rhombic antenna

Draw the radiation pattern for Dipole antenna: (i) Half wave dipole (ii) Folded dipole.

Description : Draw the radiation pattern for Dipole antenna: (i) Half wave dipole (ii) Folded dipole.

Last Answer : The radiation pattern for Half wave dipole antenna The radiation pattern for Folded dipole antenna.

___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Description : ___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Last Answer : A. Psophometer

What is the impedance in ohms of a transformer marked for 25V, 4W, when the secondary is correctly loaded? A. 150 Ω B. 156 Ω C. 160 Ω D. 165 Ω

Description : What is the impedance in ohms of a transformer marked for 25V, 4W, when the secondary is correctly loaded? A. 150 Ω B. 156 Ω C. 160 Ω D. 165 Ω

Last Answer : B. 156 Ω

When an antenna of input resistance 73 ohm is connected to a 50-ohm line and if the losses are ignored then

Description : When an antenna of input resistance 73 ohm is connected to a 50-ohm line and if the losses are ignored then its efficiency will be nearly   (A) 0.19 (B) 0.81 (C) 0.97 (D) 1.19

Last Answer : When an antenna of input resistance 73 ohm is connected to a 50-ohm line and if the losses are ignored then its efficiency will be nearly 0.81

What quarterwave transformer will match a 100Ω line to an antenna whose value is 175Ω? A. 132.29 Ω B. 150 Ω C. 16.58 Ω D. 137.5 Ω

Description : What quarterwave transformer will match a 100Ω line to an antenna whose value is 175Ω? A. 132.29 Ω B. 150 Ω C. 16.58 Ω D. 137.5 Ω

Last Answer : A. 132.29 Ω

What is the maximum line-of-sight distance between a paging antenna 250 ft high and a pager receiver 3.5ft of the ground? A. 25 km B.25mi C. 70.73 km D. 70.73 mi

Description : What is the maximum line-of-sight distance between a paging antenna 250 ft high and a pager receiver 3.5ft of the ground? A. 25 km B.25mi C. 70.73 km D. 70.73 mi

Last Answer : B.25mi

An antenna has a radiation resistance of 72 Ω a loss resistance of 8 Ω and a power gain of 16. Find efficiency and directivity.

Description : An antenna has a radiation resistance of 72 Ω a loss resistance of 8 Ω and a power gain of 16. Find efficiency and directivity.

Last Answer : An antenna has a radiation resistance of 72 Ω a loss resistance of 8 Ω and a power gain of 16. Find efficiency and directivity.

What is the effective radiated power of a repeater with 50 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 7 dB antenna gain? A. 300 W B. 315 W C. 31.5 W D. 69.9 W

Description : What is the effective radiated power of a repeater with 50 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 7 dB antenna gain? A. 300 W B. 315 W C. 31.5 W D. 69.9 W

Last Answer : C. 31.5 W

Which antenna is not grounded at one end? A. Hertz B. Marconi C. Dipole D. Whip

Description : Which antenna is not grounded at one end? A. Hertz B. Marconi C. Dipole D. Whip

Last Answer : C. Dipole

The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Description : The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Last Answer : C. increase the antenna’s power gain

What is the gain of an antenna over a half-wavelength dipole when it has 6 dB gain over an isotropic radiator? A. 6.0 dB B. 8.1 dB C. 3.9 dB D. 10.0 dB

Description : What is the gain of an antenna over a half-wavelength dipole when it has 6 dB gain over an isotropic radiator? A. 6.0 dB B. 8.1 dB C. 3.9 dB D. 10.0 dB

Last Answer : C. 3.9 dB

What antenna radiates equally in all directions? A. Vertical antenna B. isotropic antenna C. Horizontal antenna D. Dipole antenna

Description : What antenna radiates equally in all directions? A. Vertical antenna B. isotropic antenna C. Horizontal antenna D. Dipole antenna

Last Answer : B. isotropic antenna

In order to get maximum radiation to all surrounding points in the horizontal plane, the antenna used is a A. vertical loop B. vertical quarter-wavelength rod C. array which includes parasitic elements D. a horizontal Hertz dipole

Description : In order to get maximum radiation to all surrounding points in the horizontal plane, the antenna used is a A. vertical loop B. vertical quarter-wavelength rod C. array which includes parasitic elements D. a horizontal Hertz dipole

Last Answer : B. vertical quarter-wavelength rod

If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its resonant frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Description : If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its ... frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Last Answer : C. its resonant frequency will be increased

How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Description : How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Last Answer : D. By connecting an inductor in series with the antenna

The frequency of operation of a dipole antenna cut to a length of 3.4 m. A. 88 MHz B. 44 MHz C. 22 MHz D. 11 MHz

Description : The frequency of operation of a dipole antenna cut to a length of 3.4 m. A. 88 MHz B. 44 MHz C. 22 MHz D. 11 MHz

Last Answer : B. 44 MHz

An antenna which is one-tenth wavelength long A. Hertzian dipole B. Loop antenna C. Marconi antenna D. Elementary doublet

Description : An antenna which is one-tenth wavelength long A. Hertzian dipole B. Loop antenna C. Marconi antenna D. Elementary doublet

Last Answer : D. Elementary doublet

An antenna with unity gain A. Rhombic B. Half-wave dipole C. Isotropic D. Whip

Description : An antenna with unity gain A. Rhombic B. Half-wave dipole C. Isotropic D. Whip

Last Answer : C. Isotropic

What is the radiation characteristic of a dipole antenna? A. Omnidirectional B. Bidirectional C. Unidirectional D. Hemispherical

Description : What is the radiation characteristic of a dipole antenna? A. Omnidirectional B. Bidirectional C. Unidirectional D. Hemispherical

Last Answer : B. Bidirectional

Which antenna is a properly terminated? A. Marconi B. Rhombic C. Dipole D. Yagi-Uda

Description : Which antenna is a properly terminated? A. Marconi B. Rhombic C. Dipole D. Yagi-Uda

Last Answer : B. Rhombic

What is the gain of the Hertzian dipole over isotropic antenna? A. 1.64 dB B. 2.15 dB C. 1.76 dB D. 1.55 dB

Description : What is the gain of the Hertzian dipole over isotropic antenna? A. 1.64 dB B. 2.15 dB C. 1.76 dB D. 1.55 dB

Last Answer : C. 1.76 dB

What antenna can be used to minimize the effect of Faraday rotation of polarization? A. Dipole B. Parabolic C. Helical D. Rhombic

Description : What antenna can be used to minimize the effect of Faraday rotation of polarization? A. Dipole B. Parabolic C. Helical D. Rhombic

Last Answer : C. Helical

Type of antenna which is normally used for satellite tracking service. A. Omni B. Helical C. Yagi D. Dipole

Description : Type of antenna which is normally used for satellite tracking service. A. Omni B. Helical C. Yagi D. Dipole

Last Answer : B. Helical

Refers to a type of beam antenna which uses two or more straight elements arranged in line with each other. A. Dipole antenna B. Yagi antenna C. Whip antenna D. Rhombic antenna

Description : Refers to a type of beam antenna which uses two or more straight elements arranged in line with each other. A. Dipole antenna B. Yagi antenna C. Whip antenna D. Rhombic antenna

Last Answer : B. Yagi antenna

The product of the power supplied to the antenna and its gain relative to a half-wave dipole in a given direction. A. Peak envelope power B. ERP C. Rated power D. Carrier power’

Description : The product of the power supplied to the antenna and its gain relative to a half-wave dipole in a given direction. A. Peak envelope power B. ERP C. Rated power D. Carrier power’

Last Answer : B. ERP

Unity gain antenna A. Isotropic B. Rhombic C. Half-wave dipole D. Dummy

Description : Unity gain antenna A. Isotropic B. Rhombic C. Half-wave dipole D. Dummy

Last Answer : A. Isotropic

The frequency of operation of a dipole antenna cut to length of 3.4 m. A. 42.9 MHz B. 61.3 MHz C. 38.5 MHz D. 53.5 MHz

Description : The frequency of operation of a dipole antenna cut to length of 3.4 m. A. 42.9 MHz B. 61.3 MHz C. 38.5 MHz D. 53.5 MHz

Last Answer : A. 42.9 MHz

Which is properly terminated antenna? A. Rhombic B. Hertz C. Marconi D. Dipole

Description : Which is properly terminated antenna? A. Rhombic B. Hertz C. Marconi D. Dipole

Last Answer : A. Rhombic

A type of array antenna which consists of one half-wave driven dipole, one reflector and one director A. Hertzian dipole B. Yagi-uda C. Broadside collinear D. Log periodic dipole array

Description : A type of array antenna which consists of one half-wave driven dipole, one reflector and one director A. Hertzian dipole B. Yagi-uda C. Broadside collinear D. Log periodic dipole array

Last Answer : B. Yagi-uda