Description : The input terminal impedance at the center of a folded dipole antenna is A. 72 Ω B. 300 Ω C. 50 Ω D. 73 Ω
Last Answer : B. 300 Ω
Description : What is the input terminal impedance at the center if a folded dipole antenna? A. 300 ohms B. 72 ohms C. 50 ohms D. 450 ohms
Last Answer : A. 300 ohms
Description : An antenna with unity gain A. Rhombic B. Half-wave dipole C. Isotropic D. Whip
Last Answer : C. Isotropic
Description : The product of the power supplied to the antenna and its gain relative to a half-wave dipole in a given direction. A. Peak envelope power B. ERP C. Rated power D. Carrier power’
Last Answer : B. ERP
Description : Unity gain antenna A. Isotropic B. Rhombic C. Half-wave dipole D. Dummy
Last Answer : A. Isotropic
Description : A type of array antenna which consists of one half-wave driven dipole, one reflector and one director A. Hertzian dipole B. Yagi-uda C. Broadside collinear D. Log periodic dipole array
Last Answer : B. Yagi-uda
Description : ECE Board Exam March 1996 The standard reference antenna for the directive gain is ___________. A. elementary doublet B. isotropic antenna C. half-wave dipole D. infinitesimal dipole
Last Answer : B. isotropic antenna
Description : Most mobile satellite array uses ___________ in transforming 50 to 150 Ω impedance. A. stub B. balun C. quarter-wavelength transformer D. microstrip tapers.
Last Answer : C. quarter-wavelength transformer
Description : ___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter
Last Answer : A. Psophometer
Description : What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150 Ω D. 2 Ω
Last Answer : C. 150 Ω
Description : A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω
Last Answer : D. 112 Ω
Description : What is the characteristic impedance of a single wire with a diameter d= 0.25 mm placed at the center between grounded parallel planes separated by 1 mm apart. The wire is held by a material with a velocity factor of 0.75. A. 85 Ω B. 63 Ω C. 50 Ω D. 75 Ω
Last Answer : D. 75 Ω
Description : What is the impedance in ohms of a transformer marked for 25V, 4W, when the secondary is correctly loaded? A. 150 Ω B. 156 Ω C. 160 Ω D. 165 Ω
Last Answer : B. 156 Ω
Description : What is the impedance of a balance 4-wire with a diameter of 0.25 cm and spaced 2.5 cm apart using an insulator with a dielectric constant of 2.56? A. 100Ω B. 65Ω C. 75 Ω D. 50 Ω
Last Answer : A. 100Ω
Description : What is the maximum line-of-sight distance between a paging antenna 250 ft high and a pager receiver 3.5ft of the ground? A. 25 km B.25mi C. 70.73 km D. 70.73 mi
Last Answer : B.25mi
Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A
Last Answer : D. 2.0 A
Description : Determine the standing wave ratio of a 300-Ω line whose load is 400+j150 Ω. A. 3.55 B. 1.67 C. 5.53 D. 3.35
Last Answer : B. 1.67
Description : What is the gain of an antenna over a half-wavelength dipole when it has 6 dB gain over an isotropic radiator? A. 6.0 dB B. 8.1 dB C. 3.9 dB D. 10.0 dB
Last Answer : C. 3.9 dB
Description : The front-end of a television receiver, having a bandwidth of 7Mhz, and operating at a temperature of 27˚C , consists of an amplifier having a gain of 15 followed by a mixer whose gain is 20. The ... equivalent noise resistance for this television receiver. A. 8760 Ω B. 875Ω C. 8.76Ω D. 0.876Ω
Last Answer : B. 875Ω
Description : Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.
Last Answer : D. The standing wave ratio is one.
Description : What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio
Last Answer : A. Velocity factor
Description : What is the meaning of the term velocity factor of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.
Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.
Description : What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum
Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum
Description : The energy consumption and production patterns in a chemical plant over a 9 month period is provided in the table below; Month 1 2 3 4 5 6 7 8 9 Production in Tonnes / month 493 ... and give your inference on the result ? ( consider 9 month data for evaluation for predicted energy consumption)
Last Answer : It is required to use the equations Y= mX + C and nC + mΣX = ΣY cΣX + mΣX2 = ΣXY Month X = Production in Tonnes / month Y =Energy Consumption MWh /month X 2 XY 1 493 78.2 ... 73.7 54756 17240.63 8 239 64.4 57121 15402.96 9 239 72.1 57121 17228.98 3387 665.3 1410683 253221
Description : Which antenna is not grounded at one end? A. Hertz B. Marconi C. Dipole D. Whip
Last Answer : C. Dipole
Description : Which is a non-resonant antenna? A. Rhombic antenna B. Folded dipole C. End-fire array D. Yagi-Uda antenna
Last Answer : A. Rhombic antenna
Description : Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna
Last Answer : A. Center of the antenna
Description : Which is the non-resonant antenna? A. Broadside Antenna B. Folded Dipole C. Rhombic antenna D. End fire array
Last Answer : C. Rhombic antenna
Description : If a transmitting antenna is 100 meters high and a separate receiving antenna is 64 meters high, what is the maximum space wave communication distance possible between them? A. 18 km B. 72 km C. 164 km D. 656 km
Last Answer : B. 72 km
Description : Find the standing wave ratio, when a load impedance of 250 ohm is connected to a 75 ohm line. a) 0.3 b) 75 c) 250 d) 3.33
Last Answer : d) 3.33
Description : Where are the current nodes in a half-wave antenna? A. At the ends B. At the center C. Three-quarters of the way from the feed point toward the end D. One-half of the way from the feed point toward the end
Last Answer : A. At the ends
Description : Where are the voltage nodes in a half-wave antenna? A. At the ends B. Three-quarters of the way from the feed point toward the end C. One-half of the way from the feed point toward the end D. At the feed point
Last Answer : D. At the feed point
Description : Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line
Last Answer : D. load connected to the output end of a transmission line
Description : Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection
Last Answer : A. input
Description : The standard reference antenna forthe directive gain isthe a. infinitesimal dipole b. isotropic antenna c. elementary doublet d. half-wave dipole
Last Answer : b. isotropic antenna
Description : Draw the radiation pattern for Dipole antenna: (i) Half wave dipole (ii) Folded dipole.
Last Answer : The radiation pattern for Half wave dipole antenna The radiation pattern for Folded dipole antenna.
Description : The parameters of Transmission line are R = 50 Ω/ km, L= 1mH/km ,C = 0.1µf/km, G = 2µV/km. calculate characteristic impedance.
Last Answer : The parameters of Transmission line are R = 50 Ω/ km, L= 1mH/km ,C = 0.1µf/km, G = 2µV/km. calculate characteristic impedance.
Description : A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.
Last Answer : Solution
Description : The average power delivered to an impedance 4 − j 3 Ω by a current 5Cos(100πt + 100) Ampere is A) 44.2 W B) 50 W C) 62.5 W D) 125 W
Last Answer : The average power delivered to an impedance 4 − j 3 Ω by a current 5Cos(100πt + 100) Ampere is 50 W
Description : The driving point impedance with poles at ω = 0(zero) and ω = ∞ (infinity) must have the (a) s term in the denominator and an excess term in the numerator (b) s term in the ... the numerator and denominator (d) s term in the denominator and equal number of terms in the numerator and denominator
Last Answer : The driving point impedance with poles at ω = 0(zero) and ω = ∞ (infinity) must have the s term in the denominator and an excess term in the numerator
Description : A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K
Last Answer : B. 174K
Description : The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, ... this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω
Last Answer : B. 2,518 Ω
Description : A transmitted signal 5 meters in wavelength is received by an antenna coil having a 50-Ω resistance and a 0.01 H inductance. What is the capacitance of the tuner shunting the antenna coil at this point? A. 0.704 fF B. 0.704 μF C. 0.704 nF D. 0.704 mF
Last Answer : A. 0.704 fF
Description : Determine the conductance of a two-wire open line with the following parameters: D = 4 in., d = 0.1 in. and ρ = 2.6x108 Ω-m. A. 2.76x10-9 S/m B. 2.76x10-6 S/m C. 2.76x10-12 S/m D. 2.76x10-3 S/m
Last Answer : A. 2.76x10-9 S/m
Description : What quarterwave transformer will match a 100Ω line to an antenna whose value is 175Ω? A. 132.29 Ω B. 150 Ω C. 16.58 Ω D. 137.5 Ω
Last Answer : A. 132.29 Ω
Description : A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB
Last Answer : D. 8.8 dB
Description : You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12
Last Answer : C. 22
Description : An antenna has a radiation resistance of 72 Ω a loss resistance of 8 Ω and a power gain of 16. Find efficiency and directivity.
Last Answer : An antenna has a radiation resistance of 72 Ω a loss resistance of 8 Ω and a power gain of 16. Find efficiency and directivity.
Description : Private documents are given a) In section 72 b) In section 73 c) In secion 74 d) In section 75
Last Answer : d) In section 75
Description : Section -----------of companies act 1956 deals with the scheme of stock invest A. 69 to 70 B. 69 to 71 C. 69 to 72 D. 69 to 73
Last Answer : D. 69 to 73