How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

How is it possible to lower the resonant frequency of Hertz dipole antenna?
A. By reducing the frequency at the transmitter
B. By connecting a capacitor in series with the antenna
C. By the connecting a resistor in series with the antenna
D. By connecting an inductor in series with the antenna
by

1 Answer

Answer :

D. By connecting an inductor in series with the antenna
by

Related questions

Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Description : Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Last Answer : A. adding a capacitor in series and reducing the physical length

When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Description : When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Last Answer : D. Antenna resonant frequency increases

The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Description : The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Last Answer : C. increase the antenna’s power gain

If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its resonant frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Description : If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its ... frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Last Answer : C. its resonant frequency will be increased

Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Description : Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Last Answer : A. Center of the antenna

To electrically decrease the length of an antenna. A. add an inductor in series B. add an inductor in parallel C. add a resistor in series D. add a capacitor in series

Description : To electrically decrease the length of an antenna. A. add an inductor in series B. add an inductor in parallel C. add a resistor in series D. add a capacitor in series

Last Answer : D. add a capacitor in series

Increasing the electrical length of an antenna means A. add an inductor in parallel B. add a capacitor in series C. add an inductor series D. add a resistor is series

Description : Increasing the electrical length of an antenna means A. add an inductor in parallel B. add a capacitor in series C. add an inductor series D. add a resistor is series

Last Answer : C. add an inductor series

What is the effect of adding a capacitor in series with an antenna? A. The antenna’s resonant frequency will increase B. The antenna’s resonant frequency will decrease C. The antenna will be physically 5% longer than its electrical length D. A capacitor is never added in series with an antenna

Description : What is the effect of adding a capacitor in series with an antenna? A. The antenna’s resonant frequency will increase B. The antenna’s resonant frequency will decrease C. The antenna will be physically 5% longer than its electrical length D. A capacitor is never added in series with an antenna

Last Answer : A. The antenna’s resonant frequency will increase

Known as the technique for adding a series inductor at or near the center of an antenna element in order to cancel the capacitive reactance of an antenna. A. Dipole B. Center loading C. Reflector D. loading coil

Description : Known as the technique for adding a series inductor at or near the center of an antenna element in order to cancel the capacitive reactance of an antenna. A. Dipole B. Center loading C. Reflector D. loading coil

Last Answer : D. loading coil

One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. Heating of capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Description : One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. ... capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Last Answer : B. Heating of capacitor in the oscillator

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Which is a non-resonant antenna? A. Rhombic antenna B. Folded dipole C. End-fire array D. Yagi-Uda antenna

Description : Which is a non-resonant antenna? A. Rhombic antenna B. Folded dipole C. End-fire array D. Yagi-Uda antenna

Last Answer : A. Rhombic antenna

Which is the non-resonant antenna? A. Broadside Antenna B. Folded Dipole C. Rhombic antenna D. End fire array

Description : Which is the non-resonant antenna? A. Broadside Antenna B. Folded Dipole C. Rhombic antenna D. End fire array

Last Answer : C. Rhombic antenna

Which antenna is not grounded at one end? A. Hertz B. Marconi C. Dipole D. Whip

Description : Which antenna is not grounded at one end? A. Hertz B. Marconi C. Dipole D. Whip

Last Answer : C. Dipole

In order to get maximum radiation to all surrounding points in the horizontal plane, the antenna used is a A. vertical loop B. vertical quarter-wavelength rod C. array which includes parasitic elements D. a horizontal Hertz dipole

Description : In order to get maximum radiation to all surrounding points in the horizontal plane, the antenna used is a A. vertical loop B. vertical quarter-wavelength rod C. array which includes parasitic elements D. a horizontal Hertz dipole

Last Answer : B. vertical quarter-wavelength rod

Which is properly terminated antenna? A. Rhombic B. Hertz C. Marconi D. Dipole

Description : Which is properly terminated antenna? A. Rhombic B. Hertz C. Marconi D. Dipole

Last Answer : A. Rhombic

If the inductor and capacitor values are increased, what happens to the resonant frequency?

Description : If the inductor and capacitor values are increased, what happens to the resonant frequency?

Last Answer : Decreases.

The most inefficient method of voltage reduction, from the standpoint of power loss, even when placed in series with the load, is the use of a/an ____________. A. capacitor B. inductor C. resistor D. transistor

Description : The most inefficient method of voltage reduction, from the standpoint of power loss, even when placed in series with the load, is the use of a/an ____________. A. capacitor B. inductor C. resistor D. transistor

Last Answer : Answer: C

The most inefficient method of voltage reduction from the stand point of power loss, is a/an _____________. A. capacitor in series with the load B. inductor in series with the load C. capacitor and inductor in series with the load D. resistor in series with the load

Description : The most inefficient method of voltage reduction from the stand point of power loss, is a/an _____________. A. capacitor in series with the load B. inductor in series with the load C. capacitor and inductor in series with the load D. resistor in series with the load

Last Answer : Answer: D

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease

Description : If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease

Last Answer : D. decrease

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

A Hertz antenna is operating on a frequency of 2182 kHz and consists of a horizontal wire that is hanged between two towers. What is the frequency of its third harmonic? A. 727 kHz B. 6546 kHz C. 436 kHz D. 6.546 kHz

Description : A Hertz antenna is operating on a frequency of 2182 kHz and consists of a horizontal wire that is hanged between two towers. What is the frequency of its third harmonic? A. 727 kHz B. 6546 kHz C. 436 kHz D. 6.546 kHz

Last Answer : B. 6546 kHz

The frequency of operation of a dipole antenna cut to a length of 3.4 m. A. 88 MHz B. 44 MHz C. 22 MHz D. 11 MHz

Description : The frequency of operation of a dipole antenna cut to a length of 3.4 m. A. 88 MHz B. 44 MHz C. 22 MHz D. 11 MHz

Last Answer : B. 44 MHz

The frequency of operation of a dipole antenna cut to length of 3.4 m. A. 42.9 MHz B. 61.3 MHz C. 38.5 MHz D. 53.5 MHz

Description : The frequency of operation of a dipole antenna cut to length of 3.4 m. A. 42.9 MHz B. 61.3 MHz C. 38.5 MHz D. 53.5 MHz

Last Answer : A. 42.9 MHz

Two wires that are bent 90 degrees apart. A. Hertz B. Dipole C. Log-periodic D. Rhomic

Description : Two wires that are bent 90 degrees apart. A. Hertz B. Dipole C. Log-periodic D. Rhomic

Last Answer : B. Dipole

How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Description : How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Last Answer : C. Use of regulated power supply

Explain half dipole antenna ( Resonant antenna ) with its radiation patteren.

Description : Explain half dipole antenna ( Resonant antenna ) with its radiation patteren. 

Last Answer : Half wave dipole antenna Explanation:  1. It is a resonant antenna 2. It is exact half wavelength (λ /2) long & open circuited at one end. 3. The dipole antennas have ... pattern is bidirectional.  The radiation pattern of half wave dipole antenna is - The radiation pattern

Determine the lower half-power frequency of a class-C amplifier having upper half-power frequency of 10.025 MHz, a resonant frequency 5 MHz and a circuit Q of 10. A. 1.0025 MHz B. 10.525 MHz C. 0.5 MHz D. 10 MHz

Description : Determine the lower half-power frequency of a class-C amplifier having upper half-power frequency of 10.025 MHz, a resonant frequency 5 MHz and a circuit Q of 10. A. 1.0025 MHz B. 10.525 MHz C. 0.5 MHz D. 10 MHz

Last Answer : A. 1.0025 MHz

One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Description : One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Last Answer : C. Use of dummy antenna

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Last Answer : C. Carrier power

ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Description : ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Last Answer : C. gain of the antenna

Which frequency reuse method is less effective because of Faraday’s effect? A. Dual polarization B. Reducing antenna beamwidth C. Zonal rotation D. Spin stabilization

Description : Which frequency reuse method is less effective because of Faraday’s effect? A. Dual polarization B. Reducing antenna beamwidth C. Zonal rotation D. Spin stabilization

Last Answer : A. Dual polarization

For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Description : For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Last Answer : B. Near the center of the vertical radiator

Which antenna is not properly terminated? A. Resonant B. Non-resonant C. Isotropic D. Whip

Description : Which antenna is not properly terminated? A. Resonant B. Non-resonant C. Isotropic D. Whip

Last Answer : A. Resonant

Antenna which is not properly terminated A. Isotropic B. Non-resonant C. Whip D. Resonant

Description : Antenna which is not properly terminated A. Isotropic B. Non-resonant C. Whip D. Resonant

Last Answer : D. Resonant

ECE Board Exam March 1996 An antenna which is not resonant at a particular frequencies and so can be used over a wide band of frequencies and so can be used over a wide band of frequencies is called A. aperiodic B. boresight C. cassegrain D. top-loaded

Description : ECE Board Exam March 1996 An antenna which is not resonant at a particular frequencies and so can be used over a wide band of frequencies and so can be used over a wide band of frequencies is called A. aperiodic B. boresight C. cassegrain D. top-loaded

Last Answer : A. aperiodic

The 'Choke' used with a tube light is basically – (1) an inductor (2) a capacitor (3) a transformer (4) a resistor

Description : The 'Choke' used with a tube light is basically – (1) an inductor (2) a capacitor (3) a transformer (4) a resistor

Last Answer : (1) an inductor Explanation: In electronics, a choke is an inductor used to block higher-frequency alternating current (AC) in an electrical circuit, while passing lower-frequency or direct ... created by suddenly interrupting the current in choke, which is connected in series with the tubelight.

Device used to store energy in electrical circuits is A. resistor B. inductor C. capacitor D. diode

Description : Device used to store energy in electrical circuits is A. resistor B. inductor C. capacitor D. diode

Last Answer : capacitor

insulator which is placed between 2 plates of capacitor isA. electric B. dielectric C. inductor D. resistor

Description : insulator which is placed between 2 plates of capacitor isA. electric B. dielectric C. inductor D. resistor

Last Answer : dielectric

Draw the symbol of i) Iron core inductor ii) variable capacitor iii) resistor iv) Ferrite core inductor

Description : Draw the symbol of i) Iron core inductor ii) variable capacitor iii) resistor iv) Ferrite core inductor

Last Answer :  Iron core inductor:  Ferrite core inductor:  

The ‘Choke’ used with a tube light is basically (1) an inductor (2) a capacitor (3) a transformer (4) a resistor

Description : The ‘Choke’ used with a tube light is basically (1) an inductor (2) a capacitor (3) a transformer (4) a resistor

Last Answer : an inductor

State the applications and specification of (i) Resistor (ii) Capacitor (iii)Inductor

Description : State the applications and specification of (i) Resistor (ii) Capacitor (iii)Inductor

Last Answer : Application of resistor: 1.Resistors are used in high frequency instrument. 2.Resistor is used in power control circuit. 3.It is used in DC power supplies. 4.Resistors are used ... DC Current  3.Electromagnetic Interference (EMI)  4.Magnetic Saturation Flux Density  5.Curie Temperature 

Which antenna does not use the ground? A. Marconi B. Yagi C. Hertz D. Rhombic

Description : Which antenna does not use the ground? A. Marconi B. Yagi C. Hertz D. Rhombic

Last Answer : B. Yagi

Which of the following antennas receive signals in the horizontal plane equality well from all directions? A. Horizontal Hertz antenna B. Vertical loop antenna C. Vertical Yagi antenna D. A vertical antenna which is a quarter-wavelength long

Description : Which of the following antennas receive signals in the horizontal plane equality well from all directions? A. Horizontal Hertz antenna B. Vertical loop antenna C. Vertical Yagi antenna D. A vertical antenna which is a quarter-wavelength long

Last Answer : D. A vertical antenna which is a quarter-wavelength long

Which of the following antennas require good grounding? A. Yagi antenna B. Hertz antenna C. Marconi antenna D. Isotropic antenna

Description : Which of the following antennas require good grounding? A. Yagi antenna B. Hertz antenna C. Marconi antenna D. Isotropic antenna

Last Answer : C. Marconi antenna

This is a flexible vertical rod antenna commonly used on mobiles. A. Marconi B. Hertz C. Whip D. Ground plane

Description : This is a flexible vertical rod antenna commonly used on mobiles. A. Marconi B. Hertz C. Whip D. Ground plane

Last Answer : C. Whip

ECE Board Exam March 1996 A type of an underground antenna is a/an __________ antenna. A. Hertz B. isotropic C. parabolic D. Marconi

Description : ECE Board Exam March 1996 A type of an underground antenna is a/an __________ antenna. A. Hertz B. isotropic C. parabolic D. Marconi

Last Answer : A. Hertz