Possible phase relationships between voltage and current in an alternating current circuit include which of the following conditions? A. Current and voltage may be in phase. B. Current may lead the voltage. C. Current may lag the voltage. D. All of the above.

Possible phase relationships between voltage and current in an alternating current circuit include which of the following conditions? A. Current and voltage may be in phase. B. Current may lead the voltage. C. Current may lag the voltage. D. All of the above.
by

1 Answer

Answer :

Answer: D
by

Related questions

A series circuit consists of a two ohm RESISTOR and a one ohm INDUCTOR. The relationship between current and voltage is: w) current will lag by 30 degrees. x) current will lag by 26 degrees. y) current will lead by 26 degrees. z) current will lead by 30 degrees.

Description : A series circuit consists of a two ohm RESISTOR and a one ohm INDUCTOR. The relationship between current and voltage is: w) current will lag by 30 degrees. x) current will lag by 26 degrees. y) current will lead by 26 degrees. z) current will lead by 30 degrees.

Last Answer : ANSWER: X -- CURRENT WILL LAG BY 26 DEGREES.

At dead short circuit at terminals of Alternator then the current I is a) ZPF Lag b) ZPF lead c) Unity power factor d) 0.8 Power factor lag

Description : At dead short circuit at terminals of Alternator then the current I is a) ZPF Lag b) ZPF lead c) Unity power factor d) 0.8 Power factor lag

Last Answer : Ans: ZPF Lag

increases the steady state accuracy. (a) Integrator (b) Differentiator (c) Phase lead compensator (d) Phase lag compensator Ans:A 10.As a result of introduction of negative feedback which of the following will not decrease ? (a) Band width (b) Overall gain (c) Distortion (d) Instability

Description : increases the steady state accuracy. (a) Integrator (b) Differentiator (c) Phase lead compensator (d) Phase lag compensator Ans:A 10.As a result of introduction of negative feedback which of the following will not decrease ? (a) Band width (b) Overall gain (c) Distortion (d) Instability

Last Answer : Ans: A

AC and DC generators are similar in that they _____________. A. both generate alternating voltages B. both rectify the voltage before delivery C. are constructed at the same physical size for the same kilowatt rating D. both supply three-phase power

Description : AC and DC generators are similar in that they _____________. A. both generate alternating voltages B. both rectify the voltage before delivery C. are constructed at the same physical size for the same kilowatt rating D. both supply three-phase power

Last Answer : Answer: A

An open shunt field in a direct current machine may be located by connecting the field circuit to an external power source, equal to the rated field voltage or less, and tested with a voltmeter from _____________. A. one line terminal to each coil lead in succession B. one field coil to each adjacent field coil in turn C. any suitable ground to any available line lead D. any field pole to each field coil lead

Description : An open shunt field in a direct current machine may be located by connecting the field circuit to an external power source, equal to the rated field voltage or less, and tested with a voltmeter from ... C. any suitable ground to any available line lead D. any field pole to each field coil lead

Last Answer : Answer: A

The charge of a lead-acid battery can be restored by ______. A. passing an alternating electric current through the cell B. passing a direct electric current through the cell C. adding acid to the electrolyte D. all of the above

Description : The charge of a lead-acid battery can be restored by ______. A. passing an alternating electric current through the cell B. passing a direct electric current through the cell C. adding acid to the electrolyte D. all of the above

Last Answer : Answer: B

A basic premise underlying analytical procedures is that a. The study of financial ratios is an acceptable alternative to the investigation of unusual fluctuations. b. Plausible relationships among data may reasonably be expected to exist and continue in the absence of known conditions to the contrary. c. These procedures cannot replace tests of details of transactions and balances. d. Statistical tests of financial information may lead to the detection of material misstatements in the financial statements.

Description : A basic premise underlying analytical procedures is that a. The study of financial ratios is an acceptable alternative to the investigation of unusual fluctuations. b. Plausible relationships ... financial information may lead to the detection of material misstatements in the financial statements.

Last Answer : Plausible relationships among data may reasonably be expected to exist and continue in the absence of known conditions to the contrary.

The purpose of the commutator and brushes on a DC generator is to _____________. A. transfer generated direct current voltage from the armature to the line B. convert the alternating voltage generated within the armature to a direct voltage C. provide a sliding contact method to excite the field D. reduce sparking between the armature and the carbon brushes

Description : The purpose of the commutator and brushes on a DC generator is to _____________. A. transfer generated direct current voltage from the armature to the line B. convert the alternating voltage ... contact method to excite the field D. reduce sparking between the armature and the carbon brushes

Last Answer : Answer: B

Coast Guard Regulations (46 CFR) require that each alternating current generator arranged for parallel operation shall be provided with _____________. A. more than one means of excitation B. individual circuit fuses C. a high back-pressure trip D. a reverse-power trip

Description : Coast Guard Regulations (46 CFR) require that each alternating current generator arranged for parallel operation shall be provided with _____________. A. more than one means of excitation B. individual circuit fuses C. a high back-pressure trip D. a reverse-power trip

Last Answer : Answer: D

A device used in an electrical circuit to change alternating current to direct current, is known as a _____________. A. current transformer B. rectifier C. condenser D. shunt

Description : A device used in an electrical circuit to change alternating current to direct current, is known as a _____________. A. current transformer B. rectifier C. condenser D. shunt

Last Answer : Answer: B

Which of the following statements concerning AC circuits is correct? A. The power factor of a resistive circuit is always zero. B. True power in an inductive circuit always equals apparent power. C. Inductive reactance varies directly with the frequency and the inductance. D. Total opposition to the flow of alternating current depends upon the amount of reactive power.

Description : Which of the following statements concerning AC circuits is correct? A. The power factor of a resistive circuit is always zero. B. True power in an inductive circuit always equals apparent power. ... . D. Total opposition to the flow of alternating current depends upon the amount of reactive power.

Last Answer : Answer: C

The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

Description : The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

Last Answer : Answer: A

Growth curve does not include following phases of bacteria – a. Decline phase b. Stationary phase c. Lag phase d. Synchronous growth

Description : Growth curve does not include following phases of bacteria – a. Decline phase b. Stationary phase c. Lag phase d. Synchronous growth

Last Answer : Ans: D

Define Phase lag and phase lead?

Description : Define Phase lag and phase lead?

Last Answer : A negative phase angle is called phase lag. A positive phase angle is called phase lead.

A phase lag lead network introduces in the output?

Description : A phase lag lead network introduces in the output?

Last Answer : A phase lag lead network introduces in the output lag at low frequencies and lead at high frequencies.

G(s) = (1+0.5s)/(1+s) find which type of net work it is a) Lead net work b) Lag net work c) Lag – Lead net work d) Lead – Lag net work

Description : G(s) = (1+0.5s)/(1+s) find which type of net work it is a) Lead net work b) Lag net work c) Lag – Lead net work d) Lead – Lag net work

Last Answer : Ans: Lag net work

Which of the listed devices may be installed on a large diesel-electric alternating current propulsion generator? A. Temperature detector coils inserted in the stator slots for measuring stator temperature. B. A CO2 fire extinguishing system. C. Electric space heaters to prevent condensation of moisture. D. All of the above.

Description : Which of the listed devices may be installed on a large diesel-electric alternating current propulsion generator? A. Temperature detector coils inserted in the stator slots for measuring stator temperature. B. ... . C. Electric space heaters to prevent condensation of moisture. D. All of the above.

Last Answer : Answer: D

Which of the listed devices may be installed on a large turbo-electric alternating current propulsion generator? A. Temperature detector coils inserted in the stator slots for measuring stator temperature. B. A CO2 fire extinguishing system. C. Electric space heaters to prevent condensation of moisture. D. All of the above.

Description : Which of the listed devices may be installed on a large turbo-electric alternating current propulsion generator? A. Temperature detector coils inserted in the stator slots for measuring stator temperature. B. A ... . C. Electric space heaters to prevent condensation of moisture. D. All of the above.

Last Answer : Answer: D

Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on the ship's ground detection system. B. Lead 'X' will always be positive (+) with respect to ground. C. This bridge circuit output will be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.

Description : Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on ... be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.

Last Answer : Answer: B

If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the top lead positive with repect to the lower lead B. direct current, half wave rectified with a ripple frequency of 60 hz C. direct current with the top lead negative with repect to the lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Description : If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the ... lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Last Answer : Answer: C

Voltage will always lead current in a/an ______________. A. capacitive circuit B. inductive circuit C. magnetic circuit D. resistive circuit

Description : Voltage will always lead current in a/an ______________. A. capacitive circuit B. inductive circuit C. magnetic circuit D. resistive circuit

Last Answer : Answer: B

In series RLC circuit at resonant a) Voltage is in phase with current b) Current is maximum c) Inductive reactance = Capacitive reactance d) All of the above

Description : In series RLC circuit at resonant a) Voltage is in phase with current b) Current is maximum c) Inductive reactance = Capacitive reactance d) All of the above

Last Answer : Ans: All of the above

Due to the operating characteristics of the system, time lag fuses (or dual-element fuses) are necessary for use in _____________. A. main lighting circuits B. motor starting circuit C. emergency lighting circuits D. general alarm circuits

Description : Due to the operating characteristics of the system, time lag fuses (or dual-element fuses) are necessary for use in _____________. A. main lighting circuits B. motor starting circuit C. emergency lighting circuits D. general alarm circuits

Last Answer : Answer: B

Damp armature windings in a D.C. motor may lead to ____________. A. reduced voltage B. reduced current C. increased resistance D. overheating

Description : Damp armature windings in a D.C. motor may lead to ____________. A. reduced voltage B. reduced current C. increased resistance D. overheating

Last Answer : Answer: D

Under which of the following conditions will a lead-acid battery be given a 'test discharge'? A. To determine its capacity. B. Whenever a cell cannot be brought within 10 points of full charge specific gravity. C. When one or more cells is found to have less than normal voltage after an equalizing charge. D. All of the above.

Description : Under which of the following conditions will a lead-acid battery be given a 'test discharge'? A. To determine its capacity. B. Whenever a cell cannot be brought within 10 points of full charge ... cells is found to have less than normal voltage after an equalizing charge. D. All of the above.

Last Answer : Answer: D

You are attempting to parallel two AC generators and the synchroscope pointer stops at a position other than 0° prior to closing the circuit breaker. This indicates ___________. A. the frequency of the incoming machine is the same as the bus frequency B. the incoming machine is in phase with the bus, but the frequency is not the same C. the circuit breaker may be closed after breaker has been reset D. there is an existing cross current between generators

Description : You are attempting to parallel two AC generators and the synchroscope pointer stops at a position other than 0° prior to closing the circuit breaker. This indicates ___________. A. the frequency of ... be closed after breaker has been reset D. there is an existing cross current between generators

Last Answer : Answer: A

Inverse definite minimum time lag relay is also called ___________ (A) pilot relay. (B) differential relay. (C) over current relay. (D) directional overcurrent relay.

Description : Inverse definite minimum time lag relay is also called ___________ (A) pilot relay. (B) differential relay. (C) over current relay. (D) directional overcurrent relay.

Last Answer : Ans: B Inverse definite minimum time lag relay characteristic is inverse but minimum time is fixed. The operating time is inversely proportional to the magnitude of actuating quantity.

If an AC generator experiences voltage failure, the cause may be _____________. A. an open in the field circuit B. the brushes shifting out of the neutral plane C. excessive locked-rotor current D. a rotating slip ring

Description : If an AC generator experiences voltage failure, the cause may be _____________. A. an open in the field circuit B. the brushes shifting out of the neutral plane C. excessive locked-rotor current D. a rotating slip ring

Last Answer : Answer: A

Under normal conditions, the speed of a two-speed squirrel cage induction motor is changed by varying the ____________. A. frequency of the applied voltage B. resistance in the rotor circuit C. number of field poles D. amplitude of the applied voltage

Description : Under normal conditions, the speed of a two-speed squirrel cage induction motor is changed by varying the ____________. A. frequency of the applied voltage B. resistance in the rotor circuit C. number of field poles D. amplitude of the applied voltage

Last Answer : Answer: C

Which of the following conditions is most likely to occur if a single element fuse were used to replace a blown dual element fuse in a motor controller circuit? A. The fuse will blow when the motor is started. B. The fuse works, but overheats at high motor loads. C. The motor runs at reduced voltage. D. The motor runs normally.

Description : Which of the following conditions is most likely to occur if a single element fuse were used to replace a blown dual element fuse in a motor controller circuit? A. The fuse will blow when the motor ... overheats at high motor loads. C. The motor runs at reduced voltage. D. The motor runs normally.

Last Answer : Answer: A

In the illustration, A, B, C, and D are 12 volts in the circuit. What is the voltage of the lead connected to C and D with respect to the lead connected to A and B? EL-0039 A. (-) 48 volts B. (+) 48 volts C. (-) 24 volts D. (+) 24 volts

Description : In the illustration, A, B, C, and D are 12 volts in the circuit. What is the voltage of the lead connected to C and D with respect to the lead connected to A and B? EL-0039 A. (-) 48 volts B. (+) 48 volts C. (-) 24 volts D. (+) 24 volts

Last Answer : Answer: D

A lead-acid battery cell sustaining a short circuit _______. A. will be indicated by lime accumulation on the terminal posts B. will have unusually high cell voltage C. will become excessively heated while being charged D. cannot be completely discharged under load

Description : A lead-acid battery cell sustaining a short circuit _______. A. will be indicated by lime accumulation on the terminal posts B. will have unusually high cell voltage C. will become excessively heated while being charged D. cannot be completely discharged under load

Last Answer : Answer: C

When troubleshooting a lead-acid storage battery, a weak or dead cell is best detected by _________________. A. measuring and comparing all cells' specific gravity B. taking an open circuit voltage test of individual cells C. visually inspecting the electrolyte levels of each cell D. taking each cell's temperature with a calibrated mercury thermometer

Description : When troubleshooting a lead-acid storage battery, a weak or dead cell is best detected by _________________. A. measuring and comparing all cells' specific gravity B. taking an open circuit ... electrolyte levels of each cell D. taking each cell's temperature with a calibrated mercury thermometer

Last Answer : Answer: A

The open-circuit voltage of a fully charged lead-acid battery cell is _____________. A. 1.5 volts B. 1.8 volts C. 2.0 volts D. 2.3 volts

Description : The open-circuit voltage of a fully charged lead-acid battery cell is _____________. A. 1.5 volts B. 1.8 volts C. 2.0 volts D. 2.3 volts

Last Answer : Answer: C

In the illustration circuit, A, B, C, and D are each 12 volts. What is the voltage of the lead connected to C and D with respect to the lead connected to A and B? EL-0039 A. (+) 48 volts B. (-) 24 volts C. (-) 48 volts D. (+) 24 volts

Description : In the illustration circuit, A, B, C, and D are each 12 volts. What is the voltage of the lead connected to C and D with respect to the lead connected to A and B? EL-0039 A. (+) 48 volts B. (-) 24 volts C. (-) 48 volts D. (+) 24 volts

Last Answer : Answer: D

In the illustration circuit, A, B, C, and D are each 12 volts. What is the voltage at the output lead connected to 'A' and 'B' with respect to the output lead connected to 'C' and 'D'? EL-0039 A. (+) 48 volts B. (-) 24 volts C. (-) 48 volts D. (+) 24 volts

Description : In the illustration circuit, A, B, C, and D are each 12 volts. What is the voltage at the output lead connected to 'A' and 'B' with respect to the output lead connected to 'C' and 'D'? EL-0039 A. (+) 48 volts B. (-) 24 volts C. (-) 48 volts D. (+) 24 volts

Last Answer : Answer: B

Rectifiers are used to convert - (1) Direct current to Alternating current (2) Alternating current to Direct current (3) high voltage to low voltage (4) low voltage to high voltage

Description : Rectifiers are used to convert - (1) Direct current to Alternating current (2) Alternating current to Direct current (3) high voltage to low voltage (4) low voltage to high voltage

Last Answer : (2) Alternating current to Direct current Explanation: Converting DC power from one voltage to another is much more complicated. One method of DC-to-DC conversion first converts power to AC (using a ... inverter), then uses a transformer to change the voltage, and finally rectifies power back to DC.

Rectifiers are used to convert - (1) Direct current to Alternating current (2) Alternating current to Direct current (3) high voltage to low voltage (4) low voltage to high voltage

Description : Rectifiers are used to convert - (1) Direct current to Alternating current (2) Alternating current to Direct current (3) high voltage to low voltage (4) low voltage to high voltage

Last Answer : (2) Alternating current to Direct current Explanation: Converting DC power from one voltage to another is much more complicated. One method of DC-to-DC conversion first converts power to AC (using a ... inverter), then uses a transformer to change the voltage, and finally rectifies power back to DC.

When a megohmmeter is being used on a alternating current machine, the meter pointer will dip toward 'zero' and then gradually rise to the true resistance value if the motor insulation is _____________. A. grounded B. good C. shorted D. dirty

Description : When a megohmmeter is being used on a alternating current machine, the meter pointer will dip toward 'zero' and then gradually rise to the true resistance value if the motor insulation is _____________. A. grounded B. good C. shorted D. dirty

Last Answer : Answer: B

In an alternating current electrical system, a low system power factor is a direct sign of _____________. A. wasted energy B. efficient operation C. a short in the exciter field windings D. an excessive number of minor system grounds

Description : In an alternating current electrical system, a low system power factor is a direct sign of _____________. A. wasted energy B. efficient operation C. a short in the exciter field windings D. an excessive number of minor system grounds

Last Answer : Answer: A

Current flowing in only one direction is called ___________. A. alternating current B. omnidirectional current C. direct current D. sinusoidal current

Description : Current flowing in only one direction is called ___________. A. alternating current B. omnidirectional current C. direct current D. sinusoidal current

Last Answer : Answer: C

If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. will continue to operate B. will probably burn out immediately C. will operate on reduced current D. temperature will drop

Description : If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. will continue to operate B. will probably burn out immediately C. will operate on reduced current D. temperature will drop

Last Answer : Answer: B

If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. temperature will drop B. will probably burn out immediately C. will continue to operate D. will operate on reduced current

Description : If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. temperature will drop B. will probably burn out immediately C. will continue to operate D. will operate on reduced current

Last Answer : Answer: B

Which of the following components are used to convert alternating current produced in the generator windings to direct current? A. Armature and equalizer B. Commutator and brushes C. Rotor and interpoles D. Field and exciter

Description : Which of the following components are used to convert alternating current produced in the generator windings to direct current? A. Armature and equalizer B. Commutator and brushes C. Rotor and interpoles D. Field and exciter

Last Answer : Answer: B

Alternating current circuits develop resistance, inductance, and capacitance. The capacitance of individual capacitors is expressed in _____________. A. ohms B. mhos C. henrys D. farads

Description : Alternating current circuits develop resistance, inductance, and capacitance. The capacitance of individual capacitors is expressed in _____________. A. ohms B. mhos C. henrys D. farads

Last Answer : Answer: D

Alternating current circuits develop resistance, inductance and capacitance. The inductance of a coil is expressed in _____________. A. ohms B. mhos C. henrys D. farads

Description : Alternating current circuits develop resistance, inductance and capacitance. The inductance of a coil is expressed in _____________. A. ohms B. mhos C. henrys D. farads

Last Answer : Answer: C

What is Alternating Current?

Description : What is Alternating Current? 

Last Answer : Continually changing amount and direction of the current and voltage is called alternating current (AC). The components of an ac circuit causes a time period to be introduced between current and voltage; that is, current and voltage are out of phase. 

Define AC (Alternating current).

Description : Define AC (Alternating current).

Last Answer : Alternating current is that type of electric current, which changes it’s magnetude and direction periodically.