Proper storage battery maintenance includes ____________. A. keeping connections tight and casing surfaces clean B. making sure electrolyte level is below the separator plates C. insulating the terminals with naval jelly D. maintaining a high charging rate at all times

Proper storage battery maintenance includes ____________. A. keeping connections tight and casing surfaces clean B. making sure electrolyte level is below the separator plates C. insulating the terminals with naval jelly D. maintaining a high charging rate at all times
by

1 Answer

Answer :

Answer: A
by

Related questions

Routine maintenance of lead acid batteries should include _____________. A. keeping the terminals clean B. coating cable connections with petroleum jelly C. maintaining a trickle charge D. all of the above

Description : Routine maintenance of lead acid batteries should include _____________. A. keeping the terminals clean B. coating cable connections with petroleum jelly C. maintaining a trickle charge D. all of the above

Last Answer : Answer: D

A slow continual loss of electrolyte level from one cell of a storage battery could be due to _______________. A. a cracked casing B. too low a charging rate C. the specific gravity being higher than normal D. one filler cap installed too tightly

Description : A slow continual loss of electrolyte level from one cell of a storage battery could be due to _______________. A. a cracked casing B. too low a charging rate C. the specific gravity being higher than normal D. one filler cap installed too tightly

Last Answer : Answer: A

Maintenance of alkaline batteries should include _________. A. checking the electrolyte weekly using a hydrometer B. replacing the electrolyte every 5 years C. top off with sulfuric acid as needed D. making certain connections are tight and clean

Description : Maintenance of alkaline batteries should include _________. A. checking the electrolyte weekly using a hydrometer B. replacing the electrolyte every 5 years C. top off with sulfuric acid as needed D. making certain connections are tight and clean

Last Answer : Answer: D

A breakable, mercury-filled thermometer should not be used in a lead-acid battery to measure electrolyte temperature, as an accidental breakage can cause ____________. A. severe sparking and explosions B. rapid oxidation of battery plates C. violent gassing at the positive plates D. corrosion on the battery terminals

Description : A breakable, mercury-filled thermometer should not be used in a lead-acid battery to measure electrolyte temperature, as an accidental breakage can cause ____________. A. severe sparking and explosions ... battery plates C. violent gassing at the positive plates D. corrosion on the battery terminals

Last Answer : Answer: A

When charging a nickel-cadmium battery, ____________. A. the charging rate should be lessened when gassing commences B. overcharging should be avoided C. the specific gravity of the electrolyte will be unaffected by the state of charge D. add distilled water just prior to charging to insure proper mixing

Description : When charging a nickel-cadmium battery, ____________. A. the charging rate should be lessened when gassing commences B. overcharging should be avoided C. the specific gravity of the electrolyte will be ... by the state of charge D. add distilled water just prior to charging to insure proper mixing

Last Answer : Answer: C

Routine maintenance of dry-type transformers should include ______________. A. preventing the entrance of water from broken pipe lines steam lines B. keeping protective surfaces and insulating bushings free of dirt and conductive debris C. periodic testing of insulation resistance with a megger D. all of the above

Description : Routine maintenance of dry-type transformers should include ______________. A. preventing the entrance of water from broken pipe lines steam lines B. keeping protective surfaces and insulating bushings free of ... debris C. periodic testing of insulation resistance with a megger D. all of the above

Last Answer : Answer: D

Which of the substances listed should be applied to battery terminals to help prevent corrosion? A. Zinc chromate B. Naval jelly C. Lead peroxide D. Petroleum jelly

Description : Which of the substances listed should be applied to battery terminals to help prevent corrosion? A. Zinc chromate B. Naval jelly C. Lead peroxide D. Petroleum jelly

Last Answer : Answer: D

Which of the following statements, concerning the general maintenance of a brushless generator, is correct? A. Paint should be applied to insulating surfaces on an annual basis. B. Alcohol should be used to remove dust and grime from windings. C. High pressure air should be used to blow out carbon dust. D. Accessible generator parts should be wiped with a clean dry rag on a periodic basis.

Description : Which of the following statements, concerning the general maintenance of a brushless generator, is correct? A. Paint should be applied to insulating surfaces on an annual basis. B. Alcohol should be used to ... . D. Accessible generator parts should be wiped with a clean dry rag on a periodic basis.

Last Answer : Answer: D

If violent gassing occurs when a lead-acid storage battery is first placed on charge, the _____________. A. battery must be given an emergency charge B. charging rate is too low C. charging rate is too high D. specific gravity of the electrolyte solution is too low

Description : If violent gassing occurs when a lead-acid storage battery is first placed on charge, the _____________. A. battery must be given an emergency charge B. charging rate is too low C. charging rate is too high D. specific gravity of the electrolyte solution is too low

Last Answer : Answer: C

Mercury filled thermometers should never be used to determine the temperature of the battery electrolyte because accidental breakage of the thermometer can cause __________________. A. severe sparking and explosions B. rapid oxidation of battery plates C. contamination of the electrolyte D. corrosion on the battery terminals

Description : Mercury filled thermometers should never be used to determine the temperature of the battery electrolyte because accidental breakage of the thermometer can cause __________________. A. severe sparking and ... of battery plates C. contamination of the electrolyte D. corrosion on the battery terminals

Last Answer : Answer: A

When troubleshooting a console circuit card suspected of being faulty, the last step would be to _______________. A. check the fuses and voltage levels of all power supplies in the console B. clean dust and debris from the card and burnish the sliding connections C. make sure all connections are tight including wire wrappings and push-on types D. substitute a new or repaired spare card and check the operation of the circuit

Description : When troubleshooting a console circuit card suspected of being faulty, the last step would be to _______________. A. check the fuses and voltage levels of all power supplies in the console B. clean dust ... -on types D. substitute a new or repaired spare card and check the operation of the circuit

Last Answer : Answer: D

When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors are tight B. test each resistor and capacitor on the card with an ohmmeter C. check the continuity of all printed circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit

Description : When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors ... circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit

Last Answer : Answer: A

Local action in a nickel-cadmium battery is offset by _____________. A. separating the positive and negative plates with plastic spacers B. separating the positive and negative plates with resin impregnated spacers C. adding a small amount of lithium hydroxide to the electrolyte D. trickle charging

Description : Local action in a nickel-cadmium battery is offset by _____________. A. separating the positive and negative plates with plastic spacers B. separating the positive and negative plates with resin impregnated spacers C. adding a small amount of lithium hydroxide to the electrolyte D. trickle charging

Last Answer : Answer: D

When charging lead-acid batteries, the charging rate should be reduced as the battery nears its full charge to ____________. A. prevent damaging battery plates B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation

Description : When charging lead-acid batteries, the charging rate should be reduced as the battery nears its full charge to ____________. A. prevent damaging battery plates B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation

Last Answer : Answer: A

In addition to undercutting the mica, proper maintenance of a D.C. motor's commutator includes _______________. A. side-cutting the copper segments and insulating the slots B. coating the copper surface with light machine oil for the first four hours of operation C. baking the armature in an oven at a maximum of 95°C for not over 8 hours D. all of the above

Description : In addition to undercutting the mica, proper maintenance of a D.C. motor's commutator includes _______________. A. side-cutting the copper segments and insulating the slots B. coating the copper surface with light machine ... in an oven at a maximum of 95°C for not over 8 hours D. all of the above

Last Answer : Answer: A

Maintenance of alkaline batteries should include _________. A. checking the electrolyte weekly using a hydrometer B. replacing the electrolyte every 5 years C. trickle charging D. replacment when the volts per cell drops below 1.8 VDC

Description : Maintenance of alkaline batteries should include _________. A. checking the electrolyte weekly using a hydrometer B. replacing the electrolyte every 5 years C. trickle charging D. replacment when the volts per cell drops below 1.8 VDC

Last Answer : Answer: C

When troubleshooting an alkaline storage battery a weak or dead cell is best located by ____________. A. checking the specific gravity of each cell B. visually inspecting each cell's electrolyte level C. testing each cell with a voltmeter D. measuring the electrolyte temperature with an accurate mercury thermometer

Description : When troubleshooting an alkaline storage battery a weak or dead cell is best located by ____________. A. checking the specific gravity of each cell B. visually inspecting each cell's ... testing each cell with a voltmeter D. measuring the electrolyte temperature with an accurate mercury thermometer

Last Answer : Answer: C

Violent gassing from a lead-acid battery while it is being charged, indicates that the _____________. A. plate separators are grounded B. battery compartment ventilation is inadequate C. electrolyte specific gravity is too low D. charging rate is too high

Description : Violent gassing from a lead-acid battery while it is being charged, indicates that the _____________. A. plate separators are grounded B. battery compartment ventilation is inadequate C. electrolyte specific gravity is too low D. charging rate is too high

Last Answer : Answer: D

Which of the processes listed occurs during the charging of a lead-acid storage battery? A. Negative plates change to lead peroxide. B. Positive plates change to lead peroxide. C. Both plates change to lead peroxide. D. Both plates change to lead sulfate.

Description : Which of the processes listed occurs during the charging of a lead-acid storage battery? A. Negative plates change to lead peroxide. B. Positive plates change to lead peroxide. C. Both plates change to lead peroxide. D. Both plates change to lead sulfate.

Last Answer : Answer: B

Which of the following activities occurs during the charging process of a lead-acid storage battery? A. The specific gravity of the acid increases. B. Both plates change chemically to lead sulfate. C. The specific gravity of the acid decreases. D. Hydrogen gas is absorbed.

Description : Which of the following activities occurs during the charging process of a lead-acid storage battery? A. The specific gravity of the acid increases. B. Both plates change chemically to lead sulfate. C. The specific gravity of the acid decreases. D. Hydrogen gas is absorbed.

Last Answer : Answer: A

When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the battery amp-hour rating C. the source of power for charging should be 2.5 volts per cell D. gassing within the battery decreases when nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Description : When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the ... nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Last Answer : Answer: C

When a nickel-cadium battery begins gassing while connected to the battery charging circuit, you should _____________. A. do nothing as this is a normal condition when charging B. add distilled water to each cell to reduce the specific gravity of the electrolyte C. add potassium hydroxide to each cell to increase the specific gravity of the electrolyte D. decrease the charging rate

Description : When a nickel-cadium battery begins gassing while connected to the battery charging circuit, you should _____________. A. do nothing as this is a normal condition when charging B. add distilled water ... to each cell to increase the specific gravity of the electrolyte D. decrease the charging rate

Last Answer : Answer: A

Which of the following statements concerning nickel-cadmium batteries is true? A. When mixing electrolyte always add acid to the water. B. Nickel-cadmium batteries can be charged and discharged only a limited number of times without damage to the cells. C. Nickel-cadmium batteries can be stored for a long time and still keep a full charge without additional charging. D. The electrolyte of an idle nickel-cadmium battery must be replaced monthly to maintain battery condition.

Description : Which of the following statements concerning nickel-cadmium batteries is true? A. When mixing electrolyte always add acid to the water. B. Nickel-cadmium batteries can be charged and ... The electrolyte of an idle nickel-cadmium battery must be replaced monthly to maintain battery condition.

Last Answer : Answer: C

Routine maintenance of dry-type transformers should include ____________. A. cleaning the windings, if accessible, with a vacuum cleaner or very low pressure air B. measuring and recording the winding temperature with an accurate mercury thermometer C. periodic cleaning of the winding insulation with an approved solvent D. making sure that the units are close to bulkheads or corners to protect them from damage

Description : Routine maintenance of dry-type transformers should include ____________. A. cleaning the windings, if accessible, with a vacuum cleaner or very low pressure air B. measuring and recording the winding ... . making sure that the units are close to bulkheads or corners to protect them from damage

Last Answer : Answer: A

Trickle charger of a storage battery helps to A. Maintain proper electrolyte level B. Increase its reverse capacity C. Prevent sulphation D. Keep it fresh and fully charged

Description : Trickle charger of a storage battery helps to A. Maintain proper electrolyte level B. Increase its reverse capacity C. Prevent sulphation D. Keep it fresh and fully charged

Last Answer : D. Keep it fresh and fully charged

To determine the state of charge of a nickel-cadmium battery, you should ___________. A. check the electrolyte with a hydrometer B. use the constant specific gravity method C. use a nonbreakable mercury thermometer D. connect a voltmeter to the battery terminals

Description : To determine the state of charge of a nickel-cadmium battery, you should ___________. A. check the electrolyte with a hydrometer B. use the constant specific gravity method C. use a nonbreakable mercury thermometer D. connect a voltmeter to the battery terminals

Last Answer : Answer: D

Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it with a de-energized tag C. be equipped with an insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Description : Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it ... insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Last Answer : Answer: D

The standard procedure for maintaining the charge in an emergency diesel starting battery is to trickle charge the battery _____________. A. continuously B. at least once each week C. whenever the charge falls to 75% of full charge D. whenever the electrolyte specific gravity falls to 1.250 or lower

Description : The standard procedure for maintaining the charge in an emergency diesel starting battery is to trickle charge the battery _____________. A. continuously B. at least once each week C. whenever the charge falls to 75% of full charge D. whenever the electrolyte specific gravity falls to 1.250 or lower

Last Answer : Answer: A

The specific gravity of the electrolyte solution in a lead acid battery _____________. A. is not effected during charging B. remains the same during discharge C. would read close to 1.830 when discharged D. gives an indication of the state of charge of the battery

Description : The specific gravity of the electrolyte solution in a lead acid battery _____________. A. is not effected during charging B. remains the same during discharge C. would read close to 1.830 when discharged D. gives an indication of the state of charge of the battery

Last Answer : Answer: D

Complete controller maintenance includes _____________. A. periodic testing of protective devices B. checking for loose or worn contacts and weak springs C. maintaining a sufficient supply of spare parts D. all of the above

Description : Complete controller maintenance includes _____________. A. periodic testing of protective devices B. checking for loose or worn contacts and weak springs C. maintaining a sufficient supply of spare parts D. all of the above

Last Answer : Answer: D

Violent gassing developed by a lead-acid battery during charging indicates that the ____________. A. plate separators are grounded B. cell voltages are excessive C. specific gravity in insufficient D. charging rate is excessive

Description : Violent gassing developed by a lead-acid battery during charging indicates that the ____________. A. plate separators are grounded B. cell voltages are excessive C. specific gravity in insufficient D. charging rate is excessive

Last Answer : Answer: D

When the electrolyte level of a lead-acid storage battery has decreased due to normal evaporation, the level should be reestablished by adding _____________. A. distilled water only B. sulfuric acid only C. a weak solution of sulfuric acid and distilled water D. a strong solution of sulfuric acid and distilled water

Description : When the electrolyte level of a lead-acid storage battery has decreased due to normal evaporation, the level should be reestablished by adding _____________. A. distilled water only B. sulfuric acid ... of sulfuric acid and distilled water D. a strong solution of sulfuric acid and distilled water

Last Answer : Answer: A

If the illustrated device is fully discharged, what will be the result? EL-0061 A. The battery will be short circuited because the mud space will be filled with lead sulfate B. The electrolyte will be maximum sulfuric acid minimum water C. The electrolyte will be maximum water minimum sulfuric acid. D. The plates will be maximum lead oxide and sponge lead minimum lead sulfate.

Description : If the illustrated device is fully discharged, what will be the result? EL-0061 A. The battery will be short circuited because the mud space will be filled with lead sulfate B. The electrolyte ... minimum sulfuric acid. D. The plates will be maximum lead oxide and sponge lead minimum lead sulfate.

Last Answer : Answer: C

Which of the problems listed will occur if a lead-acid battery is allowed to remain in a discharged condition for a long period of time? A. The battery may be unable to accept a full charge. B. The electrolyte will change to lead sulfate. C. The concentrated sulfuric acid will attack the lead peroxide plates. D. The separators will harden.

Description : Which of the problems listed will occur if a lead-acid battery is allowed to remain in a discharged condition for a long period of time? A. The battery may be unable to accept a full charge ... . C. The concentrated sulfuric acid will attack the lead peroxide plates. D. The separators will harden.

Last Answer : Answer: A

Following will happen if battery charging rate is too high A. Excessive gassing will occur B. Temperature rise will occur C. Bulging and buckling of plates we occur D. All of the above

Description : Following will happen if battery charging rate is too high A. Excessive gassing will occur B. Temperature rise will occur C. Bulging and buckling of plates we occur D. All of the above

Last Answer : D. All of the above

Caution must be exercised during the charging of lead-acid storage batteries as _____________. A. the acid will become weaker B. hydrogen gas is being continuously liberated C. both plates are changing chemically to lead sulfate D. lead peroxide in the negative plate is poisonous

Description : Caution must be exercised during the charging of lead-acid storage batteries as _____________. A. the acid will become weaker B. hydrogen gas is being continuously liberated C. both plates are changing chemically to lead sulfate D. lead peroxide in the negative plate is poisonous

Last Answer : Answer: B

A hydrometer is used to measure the ____________. A. specific gravity of a battery electrolyte B. water pressure in a deck pipeline C. amount of potable water a vessel is taking on D. power developed by a salt water service pump

Description : A hydrometer is used to measure the ____________. A. specific gravity of a battery electrolyte B. water pressure in a deck pipeline C. amount of potable water a vessel is taking on D. power developed by a salt water service pump

Last Answer : Answer: A

When you check the specific gravity of the battery electrolyte with a hydrometer, it should be kept in mind that ____________. A. the battery is fully charged when the indicator floats low in the electrolyte B. any water that has been previously added to the cells will dilute the solution and give a false reading C. a hydrometer reading is inaccurate if taken immediately after water is added to the cell D. temperature has no effect on hydrometer readings

Description : When you check the specific gravity of the battery electrolyte with a hydrometer, it should be kept in mind that ____________. A. the battery is fully charged when the indicator floats low in ... taken immediately after water is added to the cell D. temperature has no effect on hydrometer readings

Last Answer : Answer: C

The state of charge of a lead-acid battery is best indicated by the ____________. A. individual cell voltage B. ampere-hour capacity C. electrolyte specific gravity D. total cell voltage

Description : The state of charge of a lead-acid battery is best indicated by the ____________. A. individual cell voltage B. ampere-hour capacity C. electrolyte specific gravity D. total cell voltage

Last Answer : Answer: C

The proper way to mix the electrolyte for a battery is to add _____________. A. acid to alkaline water B. acid to distilled water C. alkaline water to acid D. distilled water to acid

Description : The proper way to mix the electrolyte for a battery is to add _____________. A. acid to alkaline water B. acid to distilled water C. alkaline water to acid D. distilled water to acid

Last Answer : Answer: B

Which of the listed battery charging circuits is used to maintain a wet-cell, lead-acid, storage battery in a fully charged state during long periods of disuse? A. Normal charging circuit B. Quick charging circuit C. Trickle charging circuit D. High ampere charging circuit

Description : Which of the listed battery charging circuits is used to maintain a wet-cell, lead-acid, storage battery in a fully charged state during long periods of disuse? A. Normal charging circuit B. Quick charging circuit C. Trickle charging circuit D. High ampere charging circuit

Last Answer : Answer: C

If the bearings of an electrical generator are failing more frequently than expected and the lubricating oil is sludging then you should ______________. A. check the connections to the output leads B. check the bearing insulating block on one end of the unit C. replace the bearing with a sealed roller type D. replace the thrust bearing of the prime mover

Description : If the bearings of an electrical generator are failing more frequently than expected and the lubricating oil is sludging then you should ______________. A. check the connections to the output leads B. ... replace the bearing with a sealed roller type D. replace the thrust bearing of the prime mover

Last Answer : Answer: B

When troubleshooting a lead-acid storage battery, a weak or dead cell is best detected by _________________. A. measuring and comparing all cells' specific gravity B. taking an open circuit voltage test of individual cells C. visually inspecting the electrolyte levels of each cell D. taking each cell's temperature with a calibrated mercury thermometer

Description : When troubleshooting a lead-acid storage battery, a weak or dead cell is best detected by _________________. A. measuring and comparing all cells' specific gravity B. taking an open circuit ... electrolyte levels of each cell D. taking each cell's temperature with a calibrated mercury thermometer

Last Answer : Answer: A

When mixing electrolyte for a lead-acid storage battery, ______________. A. stirring should always be avoided B. a lead container should always be used C. always pour the water into the acid D. always pour the acid into the water

Description : When mixing electrolyte for a lead-acid storage battery, ______________. A. stirring should always be avoided B. a lead container should always be used C. always pour the water into the acid D. always pour the acid into the water

Last Answer : Answer: D

When mixing electrolyte for a lead-acid storage battery, you should pour the ___________. A. distilled water into the acid in a zinc-plated container B. distilled water into the acid in a glass container C. acid into the distilled water in a zinc-plated container D. acid into distilled water in a glass container

Description : When mixing electrolyte for a lead-acid storage battery, you should pour the ___________. A. distilled water into the acid in a zinc-plated container B. distilled water into the acid in a glass ... into the distilled water in a zinc-plated container D. acid into distilled water in a glass container

Last Answer : Answer: D

Local action in a dry-cell, or lead-acid storage battery is the process whereby ________________. A. hydrogen gas is liberated B. the electrolyte compensates for overcharging C. potassium hydroxide absorbs carbon dioxide from the air D. the battery becomes discharged without being connected to a load

Description : Local action in a dry-cell, or lead-acid storage battery is the process whereby ________________. A. hydrogen gas is liberated B. the electrolyte compensates for overcharging C. potassium hydroxide ... carbon dioxide from the air D. the battery becomes discharged without being connected to a load

Last Answer : Answer: D

The state of charge of a lead acid storage battery is best indicated by the _____________. A. testing of the individual cell voltages B. ampere hour capacity of the battery C. specific gravity of the electrolyte D. total cell voltages

Description : The state of charge of a lead acid storage battery is best indicated by the _____________. A. testing of the individual cell voltages B. ampere hour capacity of the battery C. specific gravity of the electrolyte D. total cell voltages

Last Answer : Answer: C

The electrolyte in a lead-acid storage battery consists of distilled water and _____________. A. hydrogen chloride B. calcium chloride C. sulfuric acid D. muriatic acid

Description : The electrolyte in a lead-acid storage battery consists of distilled water and _____________. A. hydrogen chloride B. calcium chloride C. sulfuric acid D. muriatic acid

Last Answer : Answer: C