Description : Proper storage battery maintenance includes ____________. A. keeping connections tight and casing surfaces clean B. making sure electrolyte level is below the separator plates C. insulating the terminals with naval jelly D. maintaining a high charging rate at all times
Last Answer : Answer: A
Description : Routine maintenance of lead acid batteries should include _____________. A. keeping the terminals clean B. coating cable connections with petroleum jelly C. maintaining a trickle charge D. all of the above
Last Answer : Answer: D
Description : From the standpoint of safety, you should never allow salt water to enter a leadacid storage battery or come in contact with sulfuric acid because ______________. A. the resulting gas is ... peroxide D. combining salt water with lead-acid creates an invisible gas resulting in severe corrosion
Last Answer : Answer: B
Description : A breakable, mercury-filled thermometer should not be used in a lead-acid battery to measure electrolyte temperature, as an accidental breakage can cause ____________. A. severe sparking and explosions ... battery plates C. violent gassing at the positive plates D. corrosion on the battery terminals
Description : Which of the processes listed occurs during the charging of a lead-acid storage battery? A. Negative plates change to lead peroxide. B. Positive plates change to lead peroxide. C. Both plates change to lead peroxide. D. Both plates change to lead sulfate.
Description : Which of the problems listed will occur if a lead-acid battery is allowed to remain in a discharged condition for a long period of time? A. The battery may be unable to accept a full charge ... . C. The concentrated sulfuric acid will attack the lead peroxide plates. D. The separators will harden.
Description : The illustrated lead acid battery is about to be placed in service. The negitive plate, labeled 'E', is made of_______. EL-0031 A. sponge lead (Pb) B. lead peroxide (PbO2) C. lead sulfate (PbSO4) D. zinc oxide (ZnO2)
Description : In areas where there is severe corrosion Finishing coat will be a) Two coats of aluminium paint to IS : 2339* b) One coat of zinc chromate priming to IS : 104 e) Two cover coats of red oxide paint to IS :123 f) One coat of zinc chrome - red oxide priming to IS : 2074
Last Answer : a) Two coats of aluminium paint to IS : 2339*
Description : In areas where there is no severe corrosion Finishing coat will be a) Two coats of aluminium paint to IS : 2339 b) One coat of zinc chromate priming to IS : 104 c) Two cover coats of red oxide paint to IS :123* d) One coat of zinc chrome - red oxide priming to IS : 2074
Last Answer : c) Two cover coats of red oxide paint to IS :123*
Description : When charging lead-acid batteries, the charging rate should be reduced as the battery nears its full charge to ____________. A. prevent damaging battery plates B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation
Description : When charging lead-acid batteries, you should reduce the charging rate as the battery nears its full charge capacity to ______________. A. prevent excessive gassing and overheating B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation
Description : Mercury filled thermometers should never be used to determine the temperature of the battery electrolyte because accidental breakage of the thermometer can cause __________________. A. severe sparking and ... of battery plates C. contamination of the electrolyte D. corrosion on the battery terminals
Description : For more complete vessel protection when using an impressed current cathodic system _____________. A. all ship's service alternators have additional temperature sensing devices and a thermal recorder ... with the hull and the propeller shaft is grounded through a slip ring/brush arrangement
Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. act as a short circuit for the sensing coil when CEMF is applied B. insure that the voltage across the coil does not exceed 9 volts C. improve response time D. act as a filter to prevent hunting
Description : The plates of a NiCad storage battery are made of ________. A. potassium hydroxide with a small amount of sulfuric acid B. lead and lead peroxide C. silver oxide and lead sulfate D. combinations of nickel powder and nickel & cadmium salts
Description : The illustrated lead acid battery is about to be placed in service. The positive plate labeled 'D' is made of_______. EL-0031 A. sponge lead (Pb) B. lead peroxide (PbO2) C. lead sulfate (PbSO4) D. a depolarizing mix
Description : Pick out the wrong statement about coating/electroplating of metals. (A) Phosphate coating is used as an excellent base for paints & enamels (B) Phosphate coating is less corrosion resistant than ... coating metal is made the anode (D) Calorising is the process of coating steel with chromium
Last Answer : (D) Calorising is the process of coating steel with chromium
Description : The removal of paint from electrical equipment, such as generators, should be cautiously undertaken because ____________. A. the mechanical shock of paint removal lessens the dielectric strength ... phase windings frequently become isolated from each other due to dust interference at the terminals
Description : Paint Zinc chromate Red oxide primer confirms to IS
Last Answer : 2074
Description : Paint Zinc chromate primer confirms to IS
Last Answer : 104
Description : When working on electrical circuits containing large capacitors, in addition to deenergizing the circuit, which of the listed precautions should also be taken? A. Keep all radio equipment ... capacitor insulation resistance. C. Ground the capacitor terminals. D. Check capacitor circuit polarity.
Last Answer : Answer: C
Description : Which of the listed ranges represents specific gravity corrected for temperature for the electrolyte of a fully charged portable lead-acid battery? A. 1.100 to 1.150 B. 1.180 to 1.200 C. 1.280 to 1.300 D. 1.750 to 2.000
Description : Which of the listed forms of water should be added to a lead-acid battery? A. saltwater B. brackish water C. distilled water D. light water
Description : Which of the listed battery charging circuits is used to maintain a wet-cell, lead-acid, storage battery in a fully charged state during long periods of disuse? A. Normal charging circuit B. Quick charging circuit C. Trickle charging circuit D. High ampere charging circuit
Description : Whic of the following pairs of materials serves as electrodes in chargeable batteries commonly used in devices such as torch lights, electric shavers, etc.? (1) Iron and cadmium (2) Nickel and cadmium (3) Lead peroxide and lead (4) Zinc and carbon
Last Answer : (2) Nickel and cadmium Explanation: A rechargeable battery, storage battery, or accumulator is a type of electrical battery. It comprises one or more electrochemical cells, and is a ... sizes, ranging from button cells to megawatt systems connected to stabilize an electrical distribution network.
Description : Which of the following pairs of materials serves as electrodes in chargeable batteries commonly used in devices such as torch lights, electric shavers, etc. ? (1) Iron and cadmium (2) Nickel and cadmium (3) Lead peroxide and lead (4) Zinc and carbon
Last Answer : Nickel and cadmium
Description : According to Coast Guard Regulations (46 CFR), which of the following is an acceptable lining for battery trays containing alkaline batteries? A. Brass B. Lead C. Steel D. Zinc
Description : When mixing electrolyte for a lead-acid storage battery, you should pour the ___________. A. distilled water into the acid in a zinc-plated container B. distilled water into the acid in a glass ... into the distilled water in a zinc-plated container D. acid into distilled water in a glass container
Description : The electrolyte used in a nickel-cadmium battery is distilled water and ______________. A. diluted sulfuric acid B. potassium hydroxide C. lead sulfate D. zinc oxide
Description : In order to prevent the corrosion of iron pipes they are often coated with a layer of zinc. This process is termed as: A. Electroplating B. Annealing C. Galvanization D. Vulcanization
Last Answer : ANSWER: C
Description : In order to prevent the corrosion of iron pipes, they are often coated with a layer of zinc. This process is termed as (a) electroplating (b) annealing (c) galvanization (d) vulcanization
Last Answer : Ans:(c)
Description : The process of covering water pipes made of Iron with Zinc layer to prevent corrosion is called – (1) Zinc plating (2) Alloy formation (3) Vulcanization (4) Galvanization
Last Answer : (4) Galvanization Explanation: Galvanization is the process of applying a protective zinc coating to steel or iron, in order to prevent rusting.
Description : In order to prevent the corrosion of iron pipes they are often coated with a layer of zinc. This process is termed as------? A. Electroplating B. Annealing C. Galvanization (Answer) D. Vulcanization
Last Answer : C. Galvanization (Answer)
Description : The process of covering water pipes made of Iron with Zinc layer to prevent corrosion is called : (1) Zinc plating (2) Alloy formation (3) Vulcanization (4) Galvanization
Last Answer : Galvanization
Description : Which of the damages listed can occur to the components of a winch master control switch, if the cover gasket becomes deteriorated? A. Overheating of the winch motor. B. Contamination of lube oil. C. Sparking at the winch motor brushes. D. Rapid corrosion of switch components.
Description : Burning of controller contacts, when opening, is prevented by _____________. A. coating the contact surfaces lightly with petroleum jelly B. magnetic blowout coils C. an overvoltage release D. an overcurrent release
Description : 1. Which country is reliant on a single export of oil/petroleum? 2. Which is the unit raised to protect the naval assets? 3. leaves used as wrappers for bides, from which are obtained? 4. Which are ... General of Ala-ud-din Khilji, was known as the Rustam of the age and the hero of the time?
Last Answer : Answer : 1. Nigeria 2. Sagar Prahari Bal 3. Tendu 4. Africa and South America 5. Brahmagupta 6. Government of India Act, 1919 7. Capacitor 8. Second Five Year Plan 9. China 10. The Guptas 11. ... . Razia Sultan 16. Isotones 17. Amjad Ali Khan 18. Fourth Five Year Plan 19. Dili 20. Malik Kafur
Description : The turns ratio of transforme 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts
Description : The turns ratio of transformer 'A' shown in the illustration is four to one and all taps are evenly spaced. If 120 volts were applied to terminals 'H1' and 'H3', what would appear at 'X1' and 'X2'? EL-0082 A. 15 volts B. 30 volts C. 480 volts D. 960 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 440 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 110 volts were applied to terminals 'X1,3' and 'X2,4', what would be indicated across 'H1' and 'H2'? EL-0082 A. 27.5 volts B. 55 volts C. 220 volts D. 440 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 110 volts B. 220 volts C. 880 volts D. 1760 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X3' and 'X4'? EL-0082 A. 55 volts B. 110 volts C. 440 volts D. 880 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X1,3' and 'X2,4'? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 880 volts
Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts
Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are evenly spaced. If 120 volts were applied to terminals 'H1' and 'H3', what would appear at 'X1' and 'X2'? EL-0082 A. 15 volts B. 30 volts C. 480 volts D. 960 volts
Description : Which of the following problems is indicated if a lead-acid battery begins to gas violently when it is first placed on charge? A. Insufficient compartment ventilation is being provided. B. A short ... undergoing its normal charging rate. D. An excessive charging rate is being applied to the battery.
Description : What is the trade name of lead chromate ?
Last Answer : The trade name for lead chromate is chrome yellow.
Description : What is used as a photocatalyst? a) Titanium dioxide b) Lead chromate c) Cobalt pigments d) Iron oxide
Last Answer : a) Titanium dioxide
Description : What material is applied to electronic assemblies to prevent damage from corrosion, moisture, and stress?
Last Answer : Conformal coating