Would bad signal on a T.V. mean a problem with the antenna?

Would bad signal on a T.V. mean a problem with the antenna?
by

1 Answer

Answer :

Yes, a bad signal on a TV mean that there is definitely a problem with your antenna. It could be that it's not working well for your television. It could also be old and it could also mean that you need to move the antenna around to get a good reception.
by

Related questions

The range of a 100 meter high T.V. transmitter antenna is about: A. 10 km B. 20 km C. 30 km D. 50 km

Description : The range of a 100 meter high T.V. transmitter antenna is about: A. 10 km B. 20 km C. 30 km D. 50 km

Last Answer : ANSWER: C

I have a roof antenna installed in 1986. Two days ago the TV stopped receiving the signal from Fox TV. Why?

Description : I have a roof antenna installed in 1986. Two days ago the TV stopped receiving the signal from Fox TV. Why?

Last Answer : answer:Go get a whole bunch of aluminum foil for hats Dumb question number # 1 Do you have a digital convertor or a TV made in the last five years? Has the convertor been re-initiated in the ... fact that the TV station says no one else has seen a change means something at your end has changed.

Will aiming a wireless router antenna at my computer help signal strength?

Description : Will aiming a wireless router antenna at my computer help signal strength?

Last Answer : this article seems to say that, yes, with a few tweaks, you could do it.

What brand of TV antenna has the best signal?

Description : What brand of TV antenna has the best signal?

Last Answer : For you, I'd such a digital antenna. I can't say that it will definitely work, but I'm suggesting this to you because I recently went through an experience where my TV wasn't picking up any reception, and I used a digital antenna which worked wonders.

Consider the following statements: 1. In a direct-to-home (DTH) system, the viewer dish antenna picks up signals from the satellite directly. 2. Cable operators receive signal from the satellite on large community dish antennas and then transmit to the viewers’ sets. Which of the above statements is/are correct? (a) Only 1 (b) Only 2 (c) Both 1 and 2 (d) Neither 1 nor 2

Description : Consider the following statements: 1. In a direct-to-home (DTH) system, the viewer dish antenna picks up signals from the satellite directly. 2. Cable operators receive signal from the satellite on large community dish antennas and ... ? (a) Only 1 (b) Only 2 (c) Both 1 and 2 (d) Neither 1 nor 2

Last Answer : Ans:(c)

If a carrier wave of 1000 kHz is used to carry the signal, the length of transmitting antenna will be equal to _______. (1) 300 m (2) 30 m (3) 3 m (4) 0.3 m

Description : If a carrier wave of 1000 kHz is used to carry the signal, the length of transmitting antenna will be equal to _______. (1) 300 m (2) 30 m (3) 3 m (4) 0.3 m

Last Answer : (1) 300 m Explanation: h = 3 × 108/106 = 300 m

Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Description : Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Last Answer : A. increases sensitivity to weak signals

A simple half-wavelength antenna radiates the strongest signal A. at 45 degrees to its axis B. parallel to its axis C. at right angles to its axis D. at 60 degrees to its axis

Description : A simple half-wavelength antenna radiates the strongest signal A. at 45 degrees to its axis B. parallel to its axis C. at right angles to its axis D. at 60 degrees to its axis

Last Answer : C. at right angles to its axis

A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW. What is the gain in dB, obtained by the use if the reflector. (Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Description : A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW ... Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Last Answer : B. 2.6

Very low signal strength in antenna. A. Minor lobes B. Null C. Antenna patterns D. Major lobes

Description : Very low signal strength in antenna. A. Minor lobes B. Null C. Antenna patterns D. Major lobes

Last Answer : B. Null

_________ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Horn antenna B. LNA C. Satellite receiver D. Satellite dish

Description : _________ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Horn antenna B. LNA C. Satellite receiver D. Satellite dish

Last Answer : B. LNA

What determines the ability of radar to determine the bearing to a target? A. Speed of light B. Speed of target C. Antenna directivity D. Frequency of signal

Description : What determines the ability of radar to determine the bearing to a target? A. Speed of light B. Speed of target C. Antenna directivity D. Frequency of signal

Last Answer : C. Antenna directivity

A transmitted signal 5 meters in wavelength is received by an antenna coil having a 50-Ω resistance and a 0.01 H inductance. What is the capacitance of the tuner shunting the antenna coil at this point? A. 0.704 fF B. 0.704 μF C. 0.704 nF D. 0.704 mF

Description : A transmitted signal 5 meters in wavelength is received by an antenna coil having a 50-Ω resistance and a 0.01 H inductance. What is the capacitance of the tuner shunting the antenna coil at this point? A. 0.704 fF B. 0.704 μF C. 0.704 nF D. 0.704 mF

Last Answer : A. 0.704 fF

What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Description : What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Last Answer : D. A frequency modulated continuous wave

One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Description : One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Last Answer : C. Use of dummy antenna

The stability of transmitted signal from a simple Hartley oscillator single transmitter which is coupled to and antenna wire affected by ______. A. Chirping of oscillator B. Closer coupling between the oscillator and the antenna. C. Location of antenna D. Material of antenna

Description : The stability of transmitted signal from a simple Hartley oscillator single transmitter which is coupled to and antenna wire affected by ______. A. Chirping of oscillator B. Closer coupling between the oscillator and the antenna. C. Location of antenna D. Material of antenna

Last Answer : B. Closer coupling between the oscillator and the antenna.

Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Description : Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Last Answer : B. 6 dB

Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Description : Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Last Answer : B. Antenna

What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Description : What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as ... antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Last Answer : B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna

An antenna that can only receive a television signal. A. Isotropic antenna B. TVRO C. Reference antenna D. Yagi antenna

Description : An antenna that can only receive a television signal. A. Isotropic antenna B. TVRO C. Reference antenna D. Yagi antenna

Last Answer : B. TVRO

Radio wave concentration in the direction of the signal emitted by a directional antenna. A. Back lobe radiation B. Side lobe radiation C. Major lobe radiation D. Transmitted signal

Description : Radio wave concentration in the direction of the signal emitted by a directional antenna. A. Back lobe radiation B. Side lobe radiation C. Major lobe radiation D. Transmitted signal

Last Answer : C. Major lobe radiation

Collects very weak signal from a broadcast satellite A. Satellite dish B. LNB C. Yagi-Uda antenna D. Satellite receiver

Description : Collects very weak signal from a broadcast satellite A. Satellite dish B. LNB C. Yagi-Uda antenna D. Satellite receiver

Last Answer : A. Satellite dish

A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 kW. What is the gain in dB obtain by the use of the reflector ? ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Description : A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 ... ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Last Answer : D. 2.6

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Description : ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Last Answer : C. gain of the antenna

If a transmitting antenna is placed close to the ground, how should the antenna be polarized to give the greatest signal strength?

Description : If a transmitting antenna is placed close to the ground, how should the antenna be polarized to give the greatest signal strength?

Last Answer : Vertically polarized.

What type of amplifier would be used to amplify the signal from a radio antenna?

Description : What type of amplifier would be used to amplify the signal from a radio antenna?

Last Answer : An rf voltage amplifier.

An automobile needs an antenna for its radio to play properly because: w) the automobile's tires insulate it from the ground. x) the automobile's body acts as a Faraday cage. y) when the automobile moves, the velocity of the radio signal appears changed with respect to when it is at rest. z) the transmitter also uses an antenna.

Description : An automobile needs an antenna for its radio to play properly because: w) the automobile's tires insulate it from the ground. x) the automobile's body acts as a Faraday cage. y) when the ... signal appears changed with respect to when it is at rest. z) the transmitter also uses an antenna.

Last Answer : ANSWER: X -- THE AUTOMOBILE'S BODY ACTS AS A FARADAY CAGE. 

Can you make up a REALLY BAD idea for a Movie Remake, Movie Adaptation of a Book or old T.V. show, or movie sequel?

Description : Can you make up a REALLY BAD idea for a Movie Remake, Movie Adaptation of a Book or old T.V. show, or movie sequel?

Last Answer : No, but I can give you a REALLY TERRIFIC idea for a remake: Der Untergang: Orange

What is the polarity of the currents that feed the V antenna?

Description : What is the polarity of the currents that feed the V antenna?

Last Answer : Opposite.

An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak

Description : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

Last Answer : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

How come when the weather turns really bad, the authorities have no problem getting as many Police officers, and D.O.T to the bottom of every mountain pass, to make sure truckers chain up?

Description : How come when the weather turns really bad, the authorities have no problem getting as many Police officers, and D.O.T to the bottom of every mountain pass, to make sure truckers chain up?

Last Answer : answer:Plow trucks cost considerably more to operate than a cruiser. Just because it has wheels and an engine, that doesn't mean that they're anything like your car. Well, unless you own something ... quality, well, that can't be true unless Conservatives have been lying to us all these decades.

A disadvantage of using a trap antenna. A. It will radiate harmonics B. It can only be used for single-bad operation C. It is too sharply directional at lower frequencies D. It must be neutralized

Description : A disadvantage of using a trap antenna. A. It will radiate harmonics B. It can only be used for single-bad operation C. It is too sharply directional at lower frequencies D. It must be neutralized

Last Answer : A. It will radiate harmonics

Is the iPhone 4's antenna problem really that big of a deal?

Description : Is the iPhone 4's antenna problem really that big of a deal?

Last Answer : answer:I honestly dont know that well because i dont follow apple or anything, but it is my understanding that it is somewhat of a firmware issue causing this problem that is supposed to be patched in the ... not really that big of a deal. like i said though, just going off what i heard from others

if noise voltage =120 mv and signal voltage = 80 v , S/N ratio in dB is?

Description : if noise voltage =120 mv and signal voltage = 80 v , S/N ratio in dB is?

Last Answer : Answers is the place to go to get the answers you need and to ask the questions you want

An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Description : An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Last Answer : D) AB

If the input to T-flipflop is 100 Hz signal, the final output of the three T-flipflops in cascade is (A) 1000 Hz (B) 500 Hz (C) 333 Hz (D) 12.5 Hz.

Description : If the input to T-flipflop is 100 Hz signal, the final output of the three T-flipflops in cascade is (A) 1000 Hz (B) 500 Hz (C) 333 Hz (D) 12.5 Hz.

Last Answer : (D) 12.5 Hz.

The analog signal given below is sampled by 600 samples per second for m(t) = 3 sin 500 pt + 2 sin 700 pt

Description : The analog signal given below is sampled by 600 samples per second for m(t) = 3 sin 500 pt + 2 sin 700 pt then folding frequency is: (1) 500 Hz (2) 700 Hz (3) 300 Hz (4) 1400 Hz 

Last Answer : The analog signal given below is sampled by 600 samples per second for m(t) = 3 sin 500 pt + 2 sin 700 pt then folding frequency is: 300 Hz

The analog signal m(t) is given below m(t) = 4 cos 100 pt + 8 sin 200 pt + cos 300 pt, the Nyquist sampling

Description : The analog signal m(t) is given below m(t) = 4 cos 100 pt + 8 sin 200 pt + cos 300 pt, the Nyquist sampling rate will be: (1) 1/100 (2) 1/200 (3) 1/300 (4) 1/600 

Last Answer : The analog signal m(t) is given below m(t) = 4 cos 100 pt + 8 sin 200 pt + cos 300 pt, the Nyquist sampling rate will be: 1/300

An absolutely integrable signal x(t) is known to have a pole at s = 2. Which one of the following

Description : An absolutely integrable signal x(t) is known to have a pole at s = 2. Which one of the following is true ? (A) B, C and D are true (B) x(t) can be left-sided (C) x(t) can be right-sided (D) x(t) can be both-sided

Last Answer : An absolutely integrable signal x(t) is known to have a pole at s = 2. Which one of the following is true ? (A) B, C and D are true (B) x(t) can be left-sided (C) x(t) can be right-sided (D) x(t) can be both-sided