Description : Which of the following procedures should be used to maintain a large electric motor during periods of inactivity? A. A thin layer of air-drying varnish should be applied on the windings. B. ... periodically to remove carbon dust. D. Space heaters should be used to prevent condensation of moisture.
Last Answer : Answer: D
Description : Before working on an electric cargo winch master switch or controller, you should _____________. A. spray the gasket surface with a solvent B. drain condensate from the box C. open the circuit breaker in the power supply and tag D. heat the switch box to remove any moisture
Last Answer : Answer: C
Description : During drying operation, it is easier to remove the __________ moisture. (A) Equilibrium (B) Critical (C) Unbound (D) Bound
Last Answer : (C) Unbound
Description : To remove all the moisture from a wet solid it requires exposure to __________ air. (A) Perfectly dry (B) Highly humid (C) High temperature (D) None of these
Last Answer : (A) Perfectly dry
Description : Calcination of iron ores is done (A) To remove moisture (B) To remove carbonic acid (C) By roasting in heaps (D) All the above
Last Answer : Answer: Option D
Description : Why it is sometimes necessary to preheat the base material before welding? a) To remove oil and grease b) To remove moisture from inside the material c) To prevent the possible risk of cracking d) Not required if using cellulosic electrodes as these will provide enough heat
Last Answer : c) To prevent the possible risk of cracking
Description : The basic function of air dryer in a compressor is: a. prevent dust from entering compressor b. storage and smoothening pulsating air output c. reduce the temperature of the air before it enters the next state to increase efficiency d. to remove remaining traces of moisture after after-cooler
Last Answer : d. to remove remaining traces of moisture after after-cooler
Description : (3) reflection of light due to the presence of free electrons Explanation: Lustre (or luster) is the way light interacts with the surface of a crystal, rock, or mineral. The word ... conductivity, and high density. Typically they are malleable and ductile, deforming -under stress without cleaving.
Last Answer : Cloud is a colloidal dispersion of – (1) Air in a dispersion medium of water (2) Fog in a dispersion medium of water (3) Mist in a dispersion medium of air (4) Water drops in a dispersion medium of air
Description : During crystallisation, formation of crystal can occur in __________ solution only. (A) Saturated (B) Supersaturated (C) Under-saturated (D) All (A), (B) and (C)
Last Answer : (B) Supersaturated
Description : Plants that grow under average tempera- ture and moisture are called?
Last Answer : mesophytes
Description : Drying operation under vacuum is carried out to (A) Dry those materials which have very high unbound moisture content (B) Reduce drying temperature (C) Increase drying temperature (D) Dry materials having high bound moisture content
Last Answer : (B) Reduce drying temperature
Description : It takes 6 hours to dry a wet solid from 50% moisture content to the critical moisture content of 15%. How much longer it will take to dry the solid to 10% moisture content, under the same drying conditions? (The ... 5%). (A) 15 min (B) 51 min (C) 71 min (D) 94 min
Last Answer : (C) 71 min
Description : In a laboratory test run, the rate of drying was found to be 0.5 x 10 - 3 kg/m2 .s, when the moisture content reduced from 0.4 to 0.1 on dry basis. The critical moisture content of the material is 0.08 on a dry ... of the solids from 0.3 to 0.2 (dry basis) is (A) 2000 (B) 4000 (C) 5000 (D) 6000
Last Answer : (C) 5000
Description : The soil moisture conservation technique under covered ground area is called: a. Fertigation b. Mulching c. Microjet irrigation d. Hydraulic
Last Answer : Mulching
Description : How should I display the "Deck Crystal" I purchased so that it reflects light in my studio the same way they did in old ships?
Last Answer : ummm… what was it supposed to do?