When wires are connected to the terminals of the battery what causes electric current in the circuit?

When wires are connected to the terminals of the battery what causes electric current in the circuit?
by

1 Answer

Answer :

The energy stored in the chemicals of the battery
by

Related questions

A battery of emf E has an internal resistance r. A variable resistacne R is connected to the terminals of the battery. A current `i` is drawn from the

Description : A battery of emf E has an internal resistance r. A variable resistacne R is connected to the terminals of the battery. A current `i` is drawn from the

Last Answer : A battery of emf E has an internal resistance r. A variable resistacne R is connected to the terminals of ... infinity, `(E)/(r)`, V approaches E

In the illustration, the signal from the device connected to terminals 18 and 19 is __________. EL-0046 A. prime mover speed feedback B. loss of control alarm when comparing with the input signal from the resistor at the top of the speed sensing circuit card C. hall effect current to detect slip between the prime mover and the alternator D. to shut down the prime mover if overspeeding

Description : In the illustration, the signal from the device connected to terminals 18 and 19 is __________. EL-0046 A. prime mover speed feedback B. loss of control alarm when comparing with the input signal ... slip between the prime mover and the alternator D. to shut down the prime mover if overspeeding

Last Answer : Answer: A

The potential drop between the terminals of a battery is equal to the battery's EMF when: w) no current is drawn from the battery x) a very large current is drawn from the battery y) the internal resistance of the battery is very large z) the resistance in the external circuit is small

Description : The potential drop between the terminals of a battery is equal to the battery's EMF when: w) no current is drawn from the battery x) a very large current is drawn from the battery y) the internal resistance of the battery is very large z) the resistance in the external circuit is small 

Last Answer : ANSWER: W -- NO CURRENT IS DRAWN FROM THE BATTERY

The potential differnce between the terminals of a battery of emf 6.0 V and internal resistance `1 Omega` drops to 5.8 V when connected across an exte

Description : The potential differnce between the terminals of a battery of emf 6.0 V and internal resistance `1 Omega` drops to 5.8 V when connected across an exte

Last Answer : The potential differnce between the terminals of a battery of emf 6.0 V and internal resistance ... resistor . Find the resistance of the external res

If a 6 volt battery were connected in series with a 24 volt battery by putting their negative terminals together, what would be the result? A. 'Zero' volts B. 12 volts of the opposite polarity C. 18 volts, positive on the 24 volt battery D. 30 volts, negative on the 24 volt battery

Description : If a 6 volt battery were connected in series with a 24 volt battery by putting their negative terminals together, what would be the result? A. 'Zero' volts B. 12 volts of the opposite polarity C. 18 volts, positive on the 24 volt battery D. 30 volts, negative on the 24 volt battery

Last Answer : Answer: C

Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it with a de-energized tag C. be equipped with an insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Description : Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it ... insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Last Answer : Answer: D

If you obtain a low resistance reading with a megohmmeter connected between terminals 'A' and 'C' of the three-phase, wye-connected winding shown in the illustration, there is __________. EL-0074 A. no open circuit between 'A' and 'C' B. no open circuit between 'C' and 'B' C. an open circuit between 'A' and 'C' D. an open circuit in both windings

Description : If you obtain a low resistance reading with a megohmmeter connected between terminals 'A' and 'C' of the three-phase, wye-connected winding shown in the illustration, there is __________. EL-0074 A. no open circuit ... 'B' C. an open circuit between 'A' and 'C' D. an open circuit in both windings

Last Answer : Answer: A

Which of the following statements is correct concerning the circuits in a sound powered telephone system? A. The ringing circuit is composed of only one common wire to ground. B. The common talking circuit is composed of two ungrounded wires. C. The ringing circuit has two grounded wires connected to each station. D. The talking and calling circuits are electrically dependent upon each other.

Description : Which of the following statements is correct concerning the circuits in a sound powered telephone system? A. The ringing circuit is composed of only one common wire to ground. B. The common ... connected to each station. D. The talking and calling circuits are electrically dependent upon each other.

Last Answer : Answer: B

When a resistance of `2 Omega` is placed across the terminals of a battery, the current is 0.5 A. When the resistance across the terminals of the batt

Description : When a resistance of `2 Omega` is placed across the terminals of a battery, the current is 0.5 A. When the resistance across the terminals of the batt

Last Answer : When a resistance of `2 Omega` is placed across the terminals of a battery, the current is 0 ... emf of the battery and also its internal resistance.

The potenital difference between the terminals of a 6.0 V battery is 7.2 V when it is being charged by a current of 2.0 A. What is the internal resist

Description : The potenital difference between the terminals of a 6.0 V battery is 7.2 V when it is being charged by a current of 2.0 A. What is the internal resist

Last Answer : The potenital difference between the terminals of a 6.0 V battery is 7.2 V when it is being ... A. What is the internal resistance of the resistor.

How do circuit breakers keep the wires in an electric circuit from overheating?

Description : How do circuit breakers keep the wires in an electric circuit from overheating?

Last Answer : They reduce the flow of electrons.

How do circuit breakers keep the wires in an electric circuit from overheating?

Description : How do circuit breakers keep the wires in an electric circuit from overheating?

Last Answer : They reduce the flow of electrons.

Two resistors `400Omega` and `800Omega` are connected in series with a `6V` battery. It is desired to measure the current in the circuit. An ammeter o

Description : Two resistors `400Omega` and `800Omega` are connected in series with a `6V` battery. It is desired to measure the current in the circuit. An ammeter o

Last Answer : Two resistors `400Omega` and `800Omega` are connected in series with a `6V` battery. It is desired to measure the current ... .95` V C. `3.8` V D. 4 V

A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt

Description : A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt

Last Answer : Answer: C

To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws of the instrument around the insulated conductor C. connect the voltage test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Description : To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws ... test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Last Answer : Answer: B

At dead short circuit at terminals of Alternator then the current I is a) ZPF Lag b) ZPF lead c) Unity power factor d) 0.8 Power factor lag

Description : At dead short circuit at terminals of Alternator then the current I is a) ZPF Lag b) ZPF lead c) Unity power factor d) 0.8 Power factor lag

Last Answer : Ans: ZPF Lag

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

Two identical conducting wires `AOB and COD` are placed at right angles to each other. The wire `AOB` carries an electric current `I_(1) and COD` carr

Description : Two identical conducting wires `AOB and COD` are placed at right angles to each other. The wire `AOB` carries an electric current `I_(1) and COD` carr

Last Answer : Two identical conducting wires `AOB and COD` are placed at right angles to each other. The wire `AOB` carries an electric ... )^(2)+I_(2)^(2))^(1//2)`

The filament of an electric lamp becomes white hot but the lead-in wires holding the filament are only slightly heated because they (a) have smaller current passing through them (b) have very low resistance (c) have higher melting point (d) are made of black iron

Description : The filament of an electric lamp becomes white hot but the lead-in wires holding the filament are only slightly heated because they (a) have smaller current passing through them (b) have very low resistance (c) have higher melting point (d) are made of black iron

Last Answer : Ans:(b)

The reading of a voltmoter when a cell is connected to it is 2.2 V. When the terminals of the cell are connected to a resistance of `4 Omega`, the vol

Description : The reading of a voltmoter when a cell is connected to it is 2.2 V. When the terminals of the cell are connected to a resistance of `4 Omega`, the vol

Last Answer : The reading of a voltmoter when a cell is connected to it is 2.2 V. When the terminals of the ... to 2 V. Find the internal resistance of the cell.

The small circular symbols to which wire '52N57E' is connected at coordinates '57L' and '57P' shown in the illustration represent ___________________. EL-0100 A. relay contact solder points B. wire wrap connections C. terminal board screws D. switch contact terminals

Description : The small circular symbols to which wire '52N57E' is connected at coordinates '57L' and '57P' shown in the illustration represent ___________________. EL-0100 A. relay contact solder points B. wire wrap connections C. terminal board screws D. switch contact terminals

Last Answer : Answer: C

The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 440 volts

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 440 volts

Last Answer : Answer: B

Figure 'D' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'D' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: A

The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 110 volts B. 220 volts C. 880 volts D. 1760 volts

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 110 volts B. 220 volts C. 880 volts D. 1760 volts

Last Answer : Answer: B

Figure 'C' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'C' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: C

Figure 'B' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'B' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: B

Figure 'A' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'A' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: B

ICT stands for : (A) International Communication Technology (B) Intera Common Terminology (C) Information and Communication Technology (D) Inter connected Terminals

Description : ICT stands for : (A) International Communication Technology (B) Intera Common Terminology (C) Information and Communication Technology (D) Inter connected Terminals

Last Answer : Answer: C

A terminal multiplexer has six 1200 bps terminals and ‘n’ 300 bps terminals connected to it. If the outgoing line is 9600 bps, what is the value of n ? (A) 4 (B) 8 (C) 16 (D) 28

Description : A terminal multiplexer has six 1200 bps terminals and ‘n’ 300 bps terminals connected to it. If the outgoing line is 9600 bps, what is the value of n ? (A) 4 (B) 8 (C) 16 (D) 28

Last Answer : (B) 8

The voltage induced across a certain coil is 200 mV. A 1200 resistor is connected to the coil terminals....

Description : The voltage induced across a certain coil is 200 mV. A 1200 resistor is connected to the coil terminals. The induced current will be: A. 1.7 mA B. 16 mA C. 12 mA D. 120 mA

Last Answer : The voltage induced across a certain coil is 200 mV. A 1200 resistor is connected to the coil terminals. The induced current will be: 1.7 mA

Can you recharge a mostly dead 9 volt battery by plugging a fresh one into the terminals?

Description : Can you recharge a mostly dead 9 volt battery by plugging a fresh one into the terminals?

Last Answer : you’ll end up ruining both and possibly start a fire.

Why is rust removed from battery terminals ?

Last Answer : Rust interferes with satisfactory electrical connection and over time rust falls through the terminal and completely destroys the terminal.

Assertion : Potential difference across the terminals of a battery is always less than the emf of the battery. Reason : During discharging of a batter

Description : Assertion : Potential difference across the terminals of a battery is always less than the emf of the battery. Reason : During discharging of a batter

Last Answer : Assertion : Potential difference across the terminals of a battery is always less than the emf of the ... . If Assertion is false but Reason is true.

What is the calculated voltage at the positive and negative terminals of the battery shown in the illustration if each cell has a voltage of 1.5 volts? EL-0034 A. 1.5 volts B. 3.0 volts C. 6.0 volts D. 12.0 volts

Description : What is the calculated voltage at the positive and negative terminals of the battery shown in the illustration if each cell has a voltage of 1.5 volts? EL-0034 A. 1.5 volts B. 3.0 volts C. 6.0 volts D. 12.0 volts

Last Answer : Answer: A

Which of the substances listed should be applied to battery terminals to help prevent corrosion? A. Zinc chromate B. Naval jelly C. Lead peroxide D. Petroleum jelly

Description : Which of the substances listed should be applied to battery terminals to help prevent corrosion? A. Zinc chromate B. Naval jelly C. Lead peroxide D. Petroleum jelly

Last Answer : Answer: D

Proper storage battery maintenance includes ____________. A. keeping connections tight and casing surfaces clean B. making sure electrolyte level is below the separator plates C. insulating the terminals with naval jelly D. maintaining a high charging rate at all times

Description : Proper storage battery maintenance includes ____________. A. keeping connections tight and casing surfaces clean B. making sure electrolyte level is below the separator plates C. insulating the terminals with naval jelly D. maintaining a high charging rate at all times

Last Answer : Answer: A

A breakable, mercury-filled thermometer should not be used in a lead-acid battery to measure electrolyte temperature, as an accidental breakage can cause ____________. A. severe sparking and explosions B. rapid oxidation of battery plates C. violent gassing at the positive plates D. corrosion on the battery terminals

Description : A breakable, mercury-filled thermometer should not be used in a lead-acid battery to measure electrolyte temperature, as an accidental breakage can cause ____________. A. severe sparking and explosions ... battery plates C. violent gassing at the positive plates D. corrosion on the battery terminals

Last Answer : Answer: A

To determine the state of charge of a nickel-cadmium battery, you should ___________. A. check the electrolyte with a hydrometer B. use the constant specific gravity method C. use a nonbreakable mercury thermometer D. connect a voltmeter to the battery terminals

Description : To determine the state of charge of a nickel-cadmium battery, you should ___________. A. check the electrolyte with a hydrometer B. use the constant specific gravity method C. use a nonbreakable mercury thermometer D. connect a voltmeter to the battery terminals

Last Answer : Answer: D

Mercury filled thermometers should never be used to determine the temperature of the battery electrolyte because accidental breakage of the thermometer can cause __________________. A. severe sparking and explosions B. rapid oxidation of battery plates C. contamination of the electrolyte D. corrosion on the battery terminals

Description : Mercury filled thermometers should never be used to determine the temperature of the battery electrolyte because accidental breakage of the thermometer can cause __________________. A. severe sparking and ... of battery plates C. contamination of the electrolyte D. corrosion on the battery terminals

Last Answer : Answer: A

How positive and negative terminals of a battery are identified?

Description : How positive and negative terminals of a battery are identified?

Last Answer : Answer: Positive terminal is identified painted with red color and negative terminal is identified painted with blue color on the top of the battery

How to Clean Car Battery Terminals

Description : How to Clean Car Battery Terminals

Last Answer : How to Clean Car Battery Terminals How to Paint a Car One of the most common causes of false starts and poor performance in many automobiles is when car battery terminals get dirty or corroded. ... these simple steps, you never have to pay big money to replace your battery and terminals again.

When two ends of a circular uniform wire are joined to the terminals of a battery, the field at the center of the circle

Last Answer : When two ends of a circular uniform wire are joined to the terminals of a battery, the field at the center of the circle will depend on the radius of the circle.

I have an older Wharfdale speaker that has lost its clarity. All the wires appear to be connected properly. Is there anything I should check or look for to improve the sound of the speaker?

Description : I have an older Wharfdale speaker that has lost its clarity. All the wires appear to be connected properly. Is there anything I should check or look for to improve the sound of the speaker?

Last Answer : I assume you’ve checked all the other equipment and tried different cables and receiver. Have you taken the speaker apart and checked the wiring inside? I don’t know what to look for except for obvious corrosion or connections that might be breaking.

What is the number of wires connected in Mesh Topology with 6 nodes ?

Description : What is the number of wires connected in Mesh Topology with 6 nodes ?

Last Answer : : The number of wires connected in Mesh topology with 6 nodes will be 26.

Two wires a and b, each of length 40 m and area of cross-section `10^(-7) m^(2)` , are connected in series and a potenital difference of 60 V is appli

Description : Two wires a and b, each of length 40 m and area of cross-section `10^(-7) m^(2)` , are connected in series and a potenital difference of 60 V is appli

Last Answer : Two wires a and b, each of length 40 m and area of cross-section `10^(-7) m^(2)` ... resistance, (ii) electric-field and (iii) current-dentsity.

Copper and carbon wires are connected in series and the combined resistor is kept at `0^(@)C`. Assuming the combined resistance does not vary with tem

Description : Copper and carbon wires are connected in series and the combined resistor is kept at `0^(@)C`. Assuming the combined resistance does not vary with tem

Last Answer : Copper and carbon wires are connected in series and the combined resistor is kept at `0^(@)C`. Assuming the combined ... C)` A. 4 B. 8 C. 6 D. 2

Two wires of the same dimensions but resistivities `rho_(1)` and `rho_(2)` are connected in series. The equivalent resistivity of the combination is

Description : Two wires of the same dimensions but resistivities `rho_(1)` and `rho_(2)` are connected in series. The equivalent resistivity of the combination is

Last Answer : Two wires of the same dimensions but resistivities `rho_(1)` and `rho_(2)` are connected in series. The equivalent ... (2))` D. `sqrt(rho_(1)rho_(2))`

How many wires are normally connected to a double- filament light bulb?

Description : How many wires are normally connected to a double- filament light bulb?

Last Answer : 5

In the illustration, the tan and white wires are connected to the solenoid valve. The solinoid valve is_________. EL-0043 A. in the liquid line before the TXV B. energized and open whenever the unit is plugged in C. not grounded so the unit must be modified before using aboard ship D. the water inlet for the ice maker

Description : In the illustration, the tan and white wires are connected to the solenoid valve. The solinoid valve is_________. EL-0043 A. in the liquid line before the TXV B. energized and open whenever the unit ... so the unit must be modified before using aboard ship D. the water inlet for the ice maker

Last Answer : Answer: D