If two volt batteries are connected in a series how many volts are available to the circuit?

If two volt batteries are connected in a series how many volts are available to the circuit?
by

1 Answer

Answer :

The formula you are looking for is Vt = V1 + V2.
by

Related questions

What will be the total output voltage if four 1.5 volt batteries are connected in a series-parallel arrangement as shown in the illustration? EL-0039 A. 1.5 volts B. 3.0 volts C. 4.5 volts D. 6.0 volts

Description : What will be the total output voltage if four 1.5 volt batteries are connected in a series-parallel arrangement as shown in the illustration? EL-0039 A. 1.5 volts B. 3.0 volts C. 4.5 volts D. 6.0 volts

Last Answer : Answer: B

Three 12 volt, lead-acid, batteries connected in series will develop __________. A. 12 volts B. 24 volts C. 36 volts D. 48 volts

Description : Three 12 volt, lead-acid, batteries connected in series will develop __________. A. 12 volts B. 24 volts C. 36 volts D. 48 volts

Last Answer : Answer: C

In the illustration, A, B, C and D are 12 volt batteries. a voltmeter across the output of the circuit will indicate _____________. EL-0039 A. 6 volts B. 12 volts C. 24 volts D. 48 volts

Description : In the illustration, A, B, C and D are 12 volt batteries. a voltmeter across the output of the circuit will indicate _____________. EL-0039 A. 6 volts B. 12 volts C. 24 volts D. 48 volts

Last Answer : Answer: C

If a 6 volt battery were connected in series with a 24 volt battery by putting their negative terminals together, what would be the result? A. 'Zero' volts B. 12 volts of the opposite polarity C. 18 volts, positive on the 24 volt battery D. 30 volts, negative on the 24 volt battery

Description : If a 6 volt battery were connected in series with a 24 volt battery by putting their negative terminals together, what would be the result? A. 'Zero' volts B. 12 volts of the opposite polarity C. 18 volts, positive on the 24 volt battery D. 30 volts, negative on the 24 volt battery

Last Answer : Answer: C

A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt

Description : A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt

Last Answer : Answer: C

Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' were connected in series-opposing to 'C' and 'B' was similarly connected to'D', the result would be _______________. EL-0039 A. 18 volts, negative at the top terminal B. 18 volts, positive at the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal

Description : Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' were connected in series-opposing to 'C' and 'B' was similarly ... the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal

Last Answer : Answer: A

Figure 'D' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'D' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: A

Figure 'C' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'C' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: C

Figure 'B' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'B' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: B

Figure 'A' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'A' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: B

Sir , if there are 9 LEDs connected in series with the 9 volt battery and each led has a forward voltage drop of 1 volt , do i need a resistor in the circuit (in series with led)?

Description : 9 leds each of 1 volt drop is series with 9  volt battery , do we need a resistor?(SMD leds) I have seen some smd leds without resistor !

Last Answer : We connect resistor to limit the current. So, it depends upon the current rating of the LED, which is provided by manufacturer.

A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Description : A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Last Answer : 50 volts.

A series R-L circuit is suddenly connected to d.c. voltage source of V volts. The current in this series ...

Description : A series R-L circuit is suddenly connected to d.c. voltage source of V volts. The current in this series circuit, just after the switch is closed, is equal to (1) Zero (2) V/L (3) V/C (4) V.L/C 

Last Answer : When is a series RLC circuit is over damped

A common-emitter circuit has an input voltage of 0.1 volt, an output voltage of 2.0 volts, an input current of 0.5 milliamps, and an output current of 10 milliamps. What is the power gain? A. 20 B. 40 C. 400 D. 4000

Description : A common-emitter circuit has an input voltage of 0.1 volt, an output voltage of 2.0 volts, an input current of 0.5 milliamps, and an output current of 10 milliamps. What is the power gain? A. 20 B. 40 C. 400 D. 4000

Last Answer : Answer: C

When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts

Description : When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts

Last Answer : Answer: B

An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Description : An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Last Answer : ANSWER: Z -- 200 OHMS

The dry-cell batteries, when connected as shown in the illustration, would produce ____________. EL-0070 A. 1.5 volts B. 2.5 volts C. 3.5 volts D. 4.5 volts

Description : The dry-cell batteries, when connected as shown in the illustration, would produce ____________. EL-0070 A. 1.5 volts B. 2.5 volts C. 3.5 volts D. 4.5 volts

Last Answer : Answer: A

Are rechargable 9 volt batteries available?

Description : Are rechargable 9 volt batteries available?

Last Answer : Yes, there are rechargeable 9-volt batteries. When purchasing one, though, be careful of its purpose; some of them are designed to deliver a higher amount of current over a shorter amount of time than others, which means they won't last very long in most devices that use this type of battery.

Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' and 'B' were reconnected to be in series-opposing to 'C' and 'D' respectively, the result would be _______________. EL-0039 A. 18 volts, negative at the top terminal B. 18 volts, positive at the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal

Description : Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' and 'B' were reconnected to be in series-opposing to 'C' and 'D' ... at the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal

Last Answer : Answer: A

When used for taking resistance measurements, a volt-ohm-milliammeter is normally powered by _____________. A. a hand cranked generator B. internal storage batteries C. the current in the circuit being tested D. a step down transformer

Description : When used for taking resistance measurements, a volt-ohm-milliammeter is normally powered by _____________. A. a hand cranked generator B. internal storage batteries C. the current in the circuit being tested D. a step down transformer

Last Answer : Answer: B

What current is required to light two 75 watt lamps and one 40 watt lamp when connected in series to a 120 volt power source? A. 0.161 amperes B. 0.631 amperes C. 1.583 amperes D. 6.199 amperes

Description : What current is required to light two 75 watt lamps and one 40 watt lamp when connected in series to a 120 volt power source? A. 0.161 amperes B. 0.631 amperes C. 1.583 amperes D. 6.199 amperes

Last Answer : Answer: C

Two 220 volt lamps, one of 60 watt and the other of 75 watt are connected in series across a 440 volt supply.

Description : Two 220 volt lamps, one of 60 watt and the other of 75 watt are connected in series across a 440 volt supply. The potential difference across 60 watt lamp will be: A) 195 volt B) 220 volt C) 245 volt D) 440 volt

Last Answer : Two 220 volt lamps, one of 60 watt and the other of 75 watt are connected in series across a 440 volt supply. The potential difference across 60 watt lamp will be: 245 volt

Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is _______________. A. 200 watts B. 100 watts C. 50 watts D. equal to the product of the amperes times the voltage in each branch

Description : Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is _______________. A. 200 watts B. 100 watts C. 50 watts D. equal to the product of the amperes times the voltage in each branch

Last Answer : Answer: A

Pin #8 of the astern valve position sensor shown in the illustration is connected _______________. EL-0099 A. to analog common B. in series with PCOM C. to (-) 50 volts D.C. D. to (+) 50 volts D.C.

Description : Pin #8 of the astern valve position sensor shown in the illustration is connected _______________. EL-0099 A. to analog common B. in series with PCOM C. to (-) 50 volts D.C. D. to (+) 50 volts D.C.

Last Answer : Answer: A

How many AC volts is 1 volt DC?

Description : How many AC volts is 1 volt DC?

Last Answer : They are apples and oranges. You can convert one to the other, depending on the amperage, but there is no corrolation between DC and AC.

1 mega volt equals how many volts ?

Description : 1 mega volt equals how many volts ?

Last Answer : 1 mega volt equals 1,00,000 ( one lakh) volts.

How many volts to run a 48 Volt club car electric motor?

Description : How many volts to run a 48 Volt club car electric motor?

Last Answer : If a 48 Volt club car electric motor requires 48 volts, then itshould be given a 48 volt power source, or something close to it.Too many more volts and it may burn out; not enough volts and itmay not run or it will try to draw too much power and burn out thepower supply.

In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Description : In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Last Answer : Answer: B

Battery capacities are given in _____________. A. volts B. volt-amperes C. volt-hours D. ampere-hours

Description : Battery capacities are given in _____________. A. volts B. volt-amperes C. volt-hours D. ampere-hours

Last Answer : Answer: D

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

Electric current is the flow of electrons through a conductor. The rate of this flow is measured as ___________. A. volts/watt B. amperes/centimetre C. coulombs/second D. ohms/volt

Description : Electric current is the flow of electrons through a conductor. The rate of this flow is measured as ___________. A. volts/watt B. amperes/centimetre C. coulombs/second D. ohms/volt

Last Answer : Answer: C

An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts

Description : An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts

Last Answer : Answer: A

If the 'E/P converter' shown in the illustration operated on a range of 1-9 volts and 6-30 PSI, a 5 volt input would yield ______________. EL-0096 A. 9 PSI B. 15 PSI C. 18 PSI D. 24 PSI

Description : If the 'E/P converter' shown in the illustration operated on a range of 1-9 volts and 6-30 PSI, a 5 volt input would yield ______________. EL-0096 A. 9 PSI B. 15 PSI C. 18 PSI D. 24 PSI

Last Answer : Answer: C

When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage is being measured B. input impedance much less than the impedance across which the voltage is being measured C. sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Description : When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage ... sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Last Answer : Answer: A

If the percentage modulation of an AM amplifier is 88% and the modulating signal is 1 volt, the carrier has an amplitude of _______________. A. 1.14 volts B. 0.88 volt C. 1.88 volts D. 0.12 volt

Description : If the percentage modulation of an AM amplifier is 88% and the modulating signal is 1 volt, the carrier has an amplitude of _______________. A. 1.14 volts B. 0.88 volt C. 1.88 volts D. 0.12 volt

Last Answer : A. 1.14 volts

The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Description : The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Last Answer : 42.

What is the unit of responsitivity? ∙ a. Ampere/volt ∙ b. Ampere/watt ∙ c. Watt/ampere ∙ d. Volts/ampere

Description : What is the unit of responsitivity? ∙ a. Ampere/volt ∙ b. Ampere/watt ∙ c. Watt/ampere ∙ d. Volts/ampere

Last Answer : ∙ a. Ampere/volt

In the illustration, A, B, C, and D are 12 volts in the circuit. What is the voltage of the lead connected to C and D with respect to the lead connected to A and B? EL-0039 A. (-) 48 volts B. (+) 48 volts C. (-) 24 volts D. (+) 24 volts

Description : In the illustration, A, B, C, and D are 12 volts in the circuit. What is the voltage of the lead connected to C and D with respect to the lead connected to A and B? EL-0039 A. (-) 48 volts B. (+) 48 volts C. (-) 24 volts D. (+) 24 volts

Last Answer : Answer: D

In the illustration circuit, A, B, C, and D are each 12 volts. What is the voltage of the lead connected to C and D with respect to the lead connected to A and B? EL-0039 A. (+) 48 volts B. (-) 24 volts C. (-) 48 volts D. (+) 24 volts

Description : In the illustration circuit, A, B, C, and D are each 12 volts. What is the voltage of the lead connected to C and D with respect to the lead connected to A and B? EL-0039 A. (+) 48 volts B. (-) 24 volts C. (-) 48 volts D. (+) 24 volts

Last Answer : Answer: D

In the illustration circuit, A, B, C, and D are each 12 volts. What is the voltage at the output lead connected to 'A' and 'B' with respect to the output lead connected to 'C' and 'D'? EL-0039 A. (+) 48 volts B. (-) 24 volts C. (-) 48 volts D. (+) 24 volts

Description : In the illustration circuit, A, B, C, and D are each 12 volts. What is the voltage at the output lead connected to 'A' and 'B' with respect to the output lead connected to 'C' and 'D'? EL-0039 A. (+) 48 volts B. (-) 24 volts C. (-) 48 volts D. (+) 24 volts

Last Answer : Answer: B

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws of the instrument around the insulated conductor C. connect the voltage test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Description : To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws ... test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Last Answer : Answer: B

Two batteries A and B each of e.m.f. 2 V are connected in series to an external resistance R = 1 ohm . If the internal resistance of battery A is 1.9

Description : Two batteries A and B each of e.m.f. 2 V are connected in series to an external resistance R = 1 ohm . If the internal resistance of battery A is 1.9

Last Answer : Two batteries A and B each of e.m.f. 2 V are connected in series to an external resistance R = 1 ohm . If the ... V B. `3.8` V C. zero D. `4.8` V

the nonideal batteries are connected in series. Consider the following statements : (A)The equivalent emf is larger than either of the two emfs. (B) t

Description : the nonideal batteries are connected in series. Consider the following statements : (A)The equivalent emf is larger than either of the two emfs. (B) t

Last Answer : the nonideal batteries are connected in series. Consider the following statements : (A)The equivalent emf is ... wrong D. Each of A and B is wrong

What power would be consumed by the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Description : What power would be consumed by the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Last Answer : Answer: D

What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Last Answer : Answer: C

The dry-cell batteries, shown in the illustration are connected in ____________. EL-0070 A. compound B. series C. parallel D. tandem

Description : The dry-cell batteries, shown in the illustration are connected in ____________. EL-0070 A. compound B. series C. parallel D. tandem

Last Answer : Answer: C

As shown in the illustration, the dry-cell batteries are connected in ____________. EL-0071 A. compound B. series C. parallel D. tandem

Description : As shown in the illustration, the dry-cell batteries are connected in ____________. EL-0071 A. compound B. series C. parallel D. tandem

Last Answer : Answer: B