1 mega volt equals how many volts ?

1 mega volt equals how many volts ?
by

1 Answer

Answer :

1 mega volt equals 1,00,000 ( one lakh) volts.
by

Related questions

1 kilovolt equals how many volts ?

Description : 1 kilovolt equals how many volts ?

Last Answer : 1 kilovolt = 1000 volts.

What are the mega doors that can be tested ?

Description : What are the mega doors that can be tested ?

Last Answer : What can be measured with a mega is mentioned below. 3 Insulating Test To do Goes 3 Earth Resistance Test To do Goes 3 Wire Continuity Test To do Goes

What is equal to 1 international volt ?

Description : What is equal to 1 international volt ?

Last Answer : 1 international volt = 1.00033 volts

How many watts equals one unit ?

Description : How many watts equals one unit ?

Last Answer : 1000 watts = 1 unit.

How many watts equals 1 horsepower ?

Description : How many watts equals 1 horsepower ?

Last Answer : One horsepower equals 646 watts.

How many AC volts is 1 volt DC?

Description : How many AC volts is 1 volt DC?

Last Answer : They are apples and oranges. You can convert one to the other, depending on the amperage, but there is no corrolation between DC and AC.

How many volts to run a 48 Volt club car electric motor?

Description : How many volts to run a 48 Volt club car electric motor?

Last Answer : If a 48 Volt club car electric motor requires 48 volts, then itshould be given a 48 volt power source, or something close to it.Too many more volts and it may burn out; not enough volts and itmay not run or it will try to draw too much power and burn out thepower supply.

If two volt batteries are connected in a series how many volts are available to the circuit?

Description : If two volt batteries are connected in a series how many volts are available to the circuit?

Last Answer : The formula you are looking for is Vt = V1 + V2.

What will be the total output voltage if four 1.5 volt batteries are connected in a series-parallel arrangement as shown in the illustration? EL-0039 A. 1.5 volts B. 3.0 volts C. 4.5 volts D. 6.0 volts

Description : What will be the total output voltage if four 1.5 volt batteries are connected in a series-parallel arrangement as shown in the illustration? EL-0039 A. 1.5 volts B. 3.0 volts C. 4.5 volts D. 6.0 volts

Last Answer : Answer: B

A common-emitter circuit has an input voltage of 0.1 volt, an output voltage of 2.0 volts, an input current of 0.5 milliamps, and an output current of 10 milliamps. What is the power gain? A. 20 B. 40 C. 400 D. 4000

Description : A common-emitter circuit has an input voltage of 0.1 volt, an output voltage of 2.0 volts, an input current of 0.5 milliamps, and an output current of 10 milliamps. What is the power gain? A. 20 B. 40 C. 400 D. 4000

Last Answer : Answer: C

Three 12 volt, lead-acid, batteries connected in series will develop __________. A. 12 volts B. 24 volts C. 36 volts D. 48 volts

Description : Three 12 volt, lead-acid, batteries connected in series will develop __________. A. 12 volts B. 24 volts C. 36 volts D. 48 volts

Last Answer : Answer: C

In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Description : In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Last Answer : Answer: B

A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt

Description : A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt

Last Answer : Answer: C

In the illustration, A, B, C and D are 12 volt batteries. a voltmeter across the output of the circuit will indicate _____________. EL-0039 A. 6 volts B. 12 volts C. 24 volts D. 48 volts

Description : In the illustration, A, B, C and D are 12 volt batteries. a voltmeter across the output of the circuit will indicate _____________. EL-0039 A. 6 volts B. 12 volts C. 24 volts D. 48 volts

Last Answer : Answer: C

Battery capacities are given in _____________. A. volts B. volt-amperes C. volt-hours D. ampere-hours

Description : Battery capacities are given in _____________. A. volts B. volt-amperes C. volt-hours D. ampere-hours

Last Answer : Answer: D

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

Electric current is the flow of electrons through a conductor. The rate of this flow is measured as ___________. A. volts/watt B. amperes/centimetre C. coulombs/second D. ohms/volt

Description : Electric current is the flow of electrons through a conductor. The rate of this flow is measured as ___________. A. volts/watt B. amperes/centimetre C. coulombs/second D. ohms/volt

Last Answer : Answer: C

An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts

Description : An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts

Last Answer : Answer: A

If a 6 volt battery were connected in series with a 24 volt battery by putting their negative terminals together, what would be the result? A. 'Zero' volts B. 12 volts of the opposite polarity C. 18 volts, positive on the 24 volt battery D. 30 volts, negative on the 24 volt battery

Description : If a 6 volt battery were connected in series with a 24 volt battery by putting their negative terminals together, what would be the result? A. 'Zero' volts B. 12 volts of the opposite polarity C. 18 volts, positive on the 24 volt battery D. 30 volts, negative on the 24 volt battery

Last Answer : Answer: C

When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts

Description : When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts

Last Answer : Answer: B

If the 'E/P converter' shown in the illustration operated on a range of 1-9 volts and 6-30 PSI, a 5 volt input would yield ______________. EL-0096 A. 9 PSI B. 15 PSI C. 18 PSI D. 24 PSI

Description : If the 'E/P converter' shown in the illustration operated on a range of 1-9 volts and 6-30 PSI, a 5 volt input would yield ______________. EL-0096 A. 9 PSI B. 15 PSI C. 18 PSI D. 24 PSI

Last Answer : Answer: C

Figure 'D' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'D' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: A

Figure 'C' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'C' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: C

Figure 'B' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'B' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: B

Figure 'A' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'A' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: B

When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage is being measured B. input impedance much less than the impedance across which the voltage is being measured C. sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Description : When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage ... sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Last Answer : Answer: A

If the percentage modulation of an AM amplifier is 88% and the modulating signal is 1 volt, the carrier has an amplitude of _______________. A. 1.14 volts B. 0.88 volt C. 1.88 volts D. 0.12 volt

Description : If the percentage modulation of an AM amplifier is 88% and the modulating signal is 1 volt, the carrier has an amplitude of _______________. A. 1.14 volts B. 0.88 volt C. 1.88 volts D. 0.12 volt

Last Answer : A. 1.14 volts

The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Description : The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Last Answer : 42.

What is the unit of responsitivity? ∙ a. Ampere/volt ∙ b. Ampere/watt ∙ c. Watt/ampere ∙ d. Volts/ampere

Description : What is the unit of responsitivity? ∙ a. Ampere/volt ∙ b. Ampere/watt ∙ c. Watt/ampere ∙ d. Volts/ampere

Last Answer : ∙ a. Ampere/volt

An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Description : An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Last Answer : ANSWER: Z -- 200 OHMS

One volt equals :

Last Answer : One volt equals : One coulomb / joule.

What is the conductivity of molar ?

Description : What is the conductivity of molar ?

Last Answer : The density of a solution as cm. When one mole of electrolytic substance is dissolved in it, the conductivity obtained by multiplying it by the relative conductivity of the solution is called molecular conductivity of the solution .

How do I purchase a product ?

Description : How do I purchase a product ?

Last Answer : From Alibaba you can purchase products by paying MASTER CARD or through bank.

What is an analog signal ?

Description : What is an analog signal ?

Last Answer : Signals whose values ​​change continuously are called analog signals. For example- voltage of electricity supplied to the house.

What is Zener Diod ?

Description : What is Zener Diod ?

Last Answer : Zener diode is a special type of diode which, like ordinary diode, not only conducts current in the forward direction , but also in the opposite direction if the voltage exceeds the level of breakdown ... diode is to use the shunt regulator and the voltage reference as the voltage of the circuit.

What is the multiplying factor of shunt ?

Description : What is the multiplying factor of shunt ?

Last Answer : Answer : The ratio of load or matte current to ammeter current is called shunt multiplying power.

What is ammeter shunt ?

Description : What is ammeter shunt ?

Last Answer : A small amount of radial coupling in parallel with the coil to increase the range of ammeter is called ammeter shunt.

What is short circuit current ?

Description : What is short circuit current ?

Last Answer : Answer : A fault in an electrical system whose current, before or after the current flows through the load, is combined with one or more phases of neutral current which causes more current to flow than normal. The current is called short circuit current.

What is a current limiting reactor ? How many types and what are they ?

Description : What is a current limiting reactor ? How many types and what are they ?

Last Answer : Answer : A current limiting reactor is basically an inductive coil which limits the short circuit current by providing inductive reactance when required. Types: 1. Based on the structure- a) Dry type ... reactor. Basbar reactors are again of 2 types- a) Ring system reactor b) Tiber system reactor

What is the method of diagnosing short circuit current ?

Description : What is the method of diagnosing short circuit current ?

Last Answer : There are three methods for determining short circuit current , namely- 1) Ohmic method 2) Per unit method 3.) Percentage reactance method.

What are symmetrical and asymmetrical faults ?

Description : What are symmetrical and asymmetrical faults ?

Last Answer : Symmetrical Fault: The same amount in each phase due to the float in the electrical system. The fault that causes hot current to flow is called semantic fault. Circuit breaker ratings are determined by ... through each fan is called an asymmetrical fault. The relay is set via asymmetrical font.

What is Basbar and Bas Kaplar ?

Description : What is Basbar and Bas Kaplar ?

Last Answer : Basbar : Basbar is basically a sheet or color of copper or aluminum. It is the job of the bus driver to deliver power to one or more lads with power from one or more cables. Bus ... is basically a combination of circuit breaker and isolator. There are fire proof walls around the bus coupler.

Why is the busbar sectionalized ?

Description : Why is the busbar sectionalized ?

Last Answer : Answer : If an error occurs in any part of the busbar, the operation of the entire busbar system will not stop. The maximum success of this system is due to the interconnection of different sections of the circuit and the smooth distribution in the outgoing circuit.

title : _

Description : title : _

Last Answer : Basbar is a type of copper and aluminum conductive sheet or mata rod , which collects electrical energy from one or more circuits and distributes that energy through one or more circuits.

Write different font names or different short circuit font names ?

Description : Write different font names or different short circuit font names ?

Last Answer : There are two main types of short circuit faults. Namely- 1. Semantic faults and 2. Asymmetrical font Symmetrical fault - a) Short circuit three phases together b) Short circuit asymmetrical fault with three ... result c) Double line to ground font d) Two phase one Circuit and third phase earth.

What is Electrical Fault ? What is the cause of the fault ?

Description : What is Electrical Fault ? What is the cause of the fault ?

Last Answer : Answer : Fault: When two or more conductors come in contact with each other while operating at normal voltage difference, the result is said to be organized. Causes of Fault: Faults are organized due to ... loss of line c) Lightning charge d) Voltage drop e) Loss of unbalance and stability etc.

What features should a switchgear have ?

Description : What features should a switchgear have ?

Last Answer : Switchgear should have the following characteristics- a) Sensitivity b) Detection ability c) Reliability d) High speed e) Durability. F) Expansion advantage g) Simplicity.

What are the components of switch gear ?

Description : What are the components of switch gear ?

Last Answer : The components of switch gear are: circuit breaker , relay , instrument transformer , housing , conductor etc.