The restriking voltage is measured in

The restriking voltage is measured in 

 (a) RMS value (b) Peak value (c) Instantaneous value (d) Average value  
by

1 Answer

Answer :

Peak value 
by

Related questions

What is restriking voltage?

Description : What is restriking voltage?

Last Answer : It is the transient voltage appearing across the breaker contacts at the instant of arc being extinguished.

What is meant by restriking voltage?

Description : What is meant by restriking voltage? 

Last Answer : The high voltage that will appear across the contact just after the quenching of the arc is called restriking voltage. 

Define: i) Arc voltage, ii) Recovery voltage, iii) Restriking voltage, iv) RRRV

Description : Define: i) Arc voltage, ii) Recovery voltage, iii) Restriking voltage, iv) RRRV

Last Answer : i) Arc Voltage: The voltage existing between the circuit breaker contacts during arcing is called as the arc voltage. It is low value compared to the system rated voltage. Normally it is around 3% ... steepest tangent to the restriking voltage curve. It is expressed in volts per micro-second.

In a battery, the difference between the no-load voltage and the measured voltage output is called ________

Description : In a battery, the difference between the no-load voltage and the measured voltage output is called ________ A) Internal voltage B) Internal resistance C) External resistance D) All the above

Last Answer : In a battery, the difference between the no-load voltage and the measured voltage output is called Internal resistance

A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured...

Description : A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured across all the resistors except the third resistor. The voltage across the third resistor is: A. 0 V B. 1.2V C. 6V D. 0.6V

Last Answer : A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured across all the resistors except the third resistor. The voltage across the third resistor is: 6V

The voltage of a circuit is measured by a voltmeter having input...

Description : The voltage of a circuit is measured by a voltmeter having input impedance comparable with the output impedance of the circuit thereby causing error in voltage measurement. This error may be called as_________.

Last Answer : error caused by misuse of instrument

What voltage would be measured across the 45 ohm resistor?

Description : What voltage would be measured across the 45 ohm resistor?

Last Answer : Not enough information. But if you know the current, you can useOhm's Law (just multiply the resistance times the current).

If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts

Description : If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts

Last Answer : Answer: A

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the voltage measured across R1 EL-0036 A. 11.86 volts B. .131 volts C. 12 volts D. .673 volts

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the voltage measured across R1 EL-0036 A. 11.86 volts B. .131 volts C. 12 volts D. .673 volts

Last Answer : Answer: B

In the illustrated circuit, what is the voltage measured across R1 if the battery is 24 volts, the resistance of R1 is 34 ohms, and the resistance of R2 is 126 ohms? EL-0036 A. 24 volts B. 18.9 volts C. 5.1 volts D. 150 millivolts

Description : In the illustrated circuit, what is the voltage measured across R1 if the battery is 24 volts, the resistance of R1 is 34 ohms, and the resistance of R2 is 126 ohms? EL-0036 A. 24 volts B. 18.9 volts C. 5.1 volts D. 150 millivolts

Last Answer : Answer: C

When troubleshooting a motor controller, all indications are that a relay coil should be energized. If there were no magnetic pull, with rated voltage measured across the coil, the most probable cause would be that the _________________. A. coil is open B. control fuse is open C. auxiliary contact in series with the coil is defective D. relay armature is stuck

Description : When troubleshooting a motor controller, all indications are that a relay coil should be energized. If there were no magnetic pull, with rated voltage measured across the coil, the most probable cause ... open C. auxiliary contact in series with the coil is defective D. relay armature is stuck

Last Answer : Answer: A

If the approximate voltage to be measured in a circuit is not known, you should _____________. A. use the lowest voltage range on the voltmeter B. connect the meter in series with the circuit C. only have to calibrate the meter before using it D. use the highest voltage range on the voltmeter

Description : If the approximate voltage to be measured in a circuit is not known, you should _____________. A. use the lowest voltage range on the voltmeter B. connect the meter in series with the circuit C. only have to calibrate the meter before using it D. use the highest voltage range on the voltmeter

Last Answer : Answer: D

In the illustration, if the device in figure 'A' has a step-up ratio of 10 to 1, what voltage should be measured at the secondary shortly after the primary of the device is connected to 110 volts DC? EL-0059 A. 0 volts B. 110 volts C. 11 volts D. 1100 volts

Description : In the illustration, if the device in figure 'A' has a step-up ratio of 10 to 1, what voltage should be measured at the secondary shortly after the primary of the device is connected to 110 volts DC? EL-0059 A. 0 volts B. 110 volts C. 11 volts D. 1100 volts

Last Answer : Answer: A

When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage is being measured B. input impedance much less than the impedance across which the voltage is being measured C. sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Description : When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage ... sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Last Answer : Answer: A

The square of the thermal noise voltage generated by a resistor is proportional to A. its resistance B. its temperature C. the bandwidth over which it is measured D. All of the above

Description : The square of the thermal noise voltage generated by a resistor is proportional to A. its resistance B. its temperature C. the bandwidth over which it is measured D. All of the above

Last Answer : D. All of the above

Indicate the false statement. A. HF mixer are generally noisier than HF amplifiers. B. Impulse noise voltage is dependent on bandwidth C. Thermal noise is independent of the frequency at which is measured. D. Industrial noise is usually of the impulse type.

Description : Indicate the false statement. A. HF mixer are generally noisier than HF amplifiers. B. Impulse noise voltage is dependent on bandwidth C. Thermal noise is independent of the frequency at which is measured. D. Industrial noise is usually of the impulse type.

Last Answer : B. Impulse noise voltage is dependent on bandwidth

Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured C. A random voltage across the resistor does not exist D. All formula referring to random noise are applicable only to the value of such noise.

Description : Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured ... exist D. All formula referring to random noise are applicable only to the value of such noise.

Last Answer : C. A random voltage across the resistor does not exist

Pick out the wrong statement. (A) The X-rays cannot be deflected by electric field unlike cathode rays (B) The intensity of X-rays can be measured by ionisation current produced due to the ionisation of gas by X-rays (C) The quality of X-rays can be controlled by varying the anode-cathode voltage (D) Crystal structure of a material can be studied by an electron microscope

Description : Pick out the wrong statement. (A) The X-rays cannot be deflected by electric field unlike cathode rays (B) The intensity of X-rays can be measured by ionisation current produced due to the ... the anode-cathode voltage (D) Crystal structure of a material can be studied by an electron microscope

Last Answer : (C) The quality of X-rays can be controlled by varying the anode-cathode voltage

If a voltage (positive or negative) is measured on the "1" output of a flip-flop, what state is it in?

Description : If a voltage (positive or negative) is measured on the "1" output of a flip-flop, what state is it in?

Last Answer : SET state.

In what manner are voltage-measuring instruments connected to the circuit to be measured?

Description : In what manner are voltage-measuring instruments connected to the circuit to be measured?

Last Answer : In parallel.

Which one of the following statements is not correct? A Since voltage depends on concentrations, using standard conditions makes it easier to compare different electrochemical reactions. B We have to measure the cell potential to obtain the difference in potential energy because the potential of half-reactions cannot be measured directly. C The direction of a redox reaction can only be determined experimentally. D Half-cell potentials for half-reactions are determined by combining the relevant half-cell with a standardised half-cell.

Description : Which one of the following statements is not correct? A Since voltage depends on concentrations, using standard conditions makes it easier to compare different electrochemical reactions. B We have ... half-reactions are determined by combining the relevant half-cell with a standardised half-cell.

Last Answer : C The direction of a redox reaction can only be determined experimentally. 

Which one of the following is the name of a device used to measure voltage without drawing ANY current from the circuit being measured? Is it: w) a wattmeter x) a galvanometer y) an ammeter z) a potentiometer

Description : Which one of the following is the name of a device used to measure voltage without drawing ANY current from the circuit being measured? Is it: w) a wattmeter x) a galvanometer y) an ammeter z) a potentiometer

Last Answer : ANSWER: Z -- A POTENTIOMETER

In a standard multimeter for measuring AC voltage, parameter of _____ voltage is measured

Description : In a standard multimeter for measuring AC voltage, parameter of _____ voltage is measured

Last Answer : In a standard multimeter for measuring AC voltage, parameter of RMS voltage is measured

Four amperes of current are measured through a 24 ohms resistor connected across a voltage

Description : Four amperes of current are measured through a 24 ohms resistor connected across a voltage source. How much voltage does the source produce? A.960 V B.9.6 V C.96 V D.8 V

Last Answer : Four amperes of current are measured through a 24 ohms resistor connected across a voltage source. How much voltage does the source produce? A.960 V B.9.6 V C.96 V D.8 V

When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But

Description : When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But when the same voltage is measured using a Permanent Magnet Moving Coil (PMMC) voltmeter, the voltmeter reading shows 0.99 ... resistance of the battery, in Ohm , is (A) 150 (B) 100 (C) 50 (D) 200

Last Answer : When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But when the same voltage is measured using a Permanent Magnet Moving Coil (PMMC) voltmeter, ... resistance of the voltmeter is 1100 Ohm , the internal resistance of the battery, in Ohm , is 100

A voltage of about 200 V can be measured?

Description :

Last Answer : A voltage of about 200 V can be measured a D.C. potentiometer in conjunction with a volt ratio box.