A voltage of about 200 V can be measured?


by
edited

1 Answer

Answer :

A voltage of about 200 V can be measured a D.C. potentiometer in conjunction with a volt ratio box.
by

Related questions

When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But

Description : When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But when the same voltage is measured using a Permanent Magnet Moving Coil (PMMC) voltmeter, the voltmeter reading shows 0.99 ... resistance of the battery, in Ohm , is (A) 150 (B) 100 (C) 50 (D) 200

Last Answer : When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But when the same voltage is measured using a Permanent Magnet Moving Coil (PMMC) voltmeter, ... resistance of the voltmeter is 1100 Ohm , the internal resistance of the battery, in Ohm , is 100

In a standard multimeter for measuring AC voltage, parameter of _____ voltage is measured

Description : In a standard multimeter for measuring AC voltage, parameter of _____ voltage is measured

Last Answer : In a standard multimeter for measuring AC voltage, parameter of RMS voltage is measured

A 200 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure circuit is 8000 Ω

Description : A 200 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure circuit is 8000 Ω and that of current coil is 0.1 Ω. The power consumed when testing the meter with phantom loading with current circuit excited by a 6 V battery is (A) 2.5 W (B) 5 W (C) 32.5 W (D) 35 W

Last Answer : A 200 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure circuit is 8000 Ω and that of current coil is 0.1 Ω. The power consumed when testing the meter with phantom loading with current circuit excited by a 6 V battery is 35 W

In a balanced 3 -phase 200 V circuit, the line current is 115.5 A. When the power is measured by two...

Description : In a balanced 3 -phase 200 V circuit, the line current is 115.5 A. When the power is measured by two wattmeter method, one of the wattmeters reads 20 kW and the other one reads zero. What is the power factor of the load ?

Last Answer : In a balanced 3 -phase 200 V circuit, the line current is 115.5 A. When the power is measured by two wattmeter method, one of the wattmeters reads 20 kW and the other one reads zero. What is the power factor of the load ?  0.5

A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured...

Description : A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured across all the resistors except the third resistor. The voltage across the third resistor is: A. 0 V B. 1.2V C. 6V D. 0.6V

Last Answer : A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured across all the resistors except the third resistor. The voltage across the third resistor is: 6V

The required DC voltage for arc welding is- (1) 6 to 9 V (2) 50 to 60 V (3) 200 to 250 V (4) 90 to 100 V

Description : The required DC voltage for arc welding is- (1) 6 to 9 V (2) 50 to 60 V (3) 200 to 250 V (4) 90 to 100 V

Last Answer : (3) 200 to 250 V

Two unpedauces given by Z1 = 10 + j5 and Z2 = 8 + j9 are joined in parallel and connected across a voltage of V = 200 + j0. Calculate the circuit current and branch currents. Draw the vector diagram.

Description : Two unpedauces given by Z1 = 10 + j5 and Z2 = 8 + j9 are joined in parallel and connected across a voltage of V = 200 + j0. Calculate the circuit current and branch currents. Draw the vector diagram.

Last Answer : Solution: Given, Z1=10+j5, Z2=8+j9, V=200+j0

An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak

Description : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

Last Answer : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is

Description : In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is   (a) 233.91 V (b) 116.95V (c) 202.56 V (d) 101.28V 

Last Answer : a

A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W....

Description : A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ?  (a) 100 VAR (b) 200 VAR (c) 300 VAR (d) 400 VAR

Last Answer : A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ? 400 VAR

The power delivered to a 3-phase load can be measured by the use of two wattmeters only

Description : The power delivered to a 3-phase load can be measured by the use of two wattmeters only when the  (a) load is unbalanced (b) load is balanced (c) three phase load is connected to the source through three wires (d) three phase load is connected to the source through four wires

Last Answer : The power delivered to a 3-phase load can be measured by the use of two wattmeters only when the three phase load is connected to the source through three wires 

True value has been 50 whereas measured value is 40 then the percentage error in the reading

Description : True value has been 50 whereas measured value is 40 then the percentage error in the reading will be ______.  (A) 20% (B) 40% (C) 50% (D) 30%

Last Answer : True value has been 50 whereas measured value is 40 then the percentage error in the reading will be 20%. 

The self inductance of a coil can be measured using

Description : The self inductance of a coil can be measured using (A) Wien’s Bridge (B) Schering Bridge (C) Anderson’s Bridge (D) Wheatstone Bridge

Last Answer : The self inductance of a coil can be measured using Anderson’s Bridge

Dielectric loss in a capacitor is best measured by

Description : Dielectric loss in a capacitor is best measured by (A) Wien Bridge (B) Schering Bridge (C) Anderson Bridge (D) Heaviside-Campbell Equal Ratio Bridge

Last Answer : Dielectric loss in a capacitor is best measured by Schering Bridge

Low resistance is measured by

Last Answer : Low resistance is measured by Kelvin’s double bridge.

The dielectric loss of capacitance can be measured by

Last Answer : The dielectric loss of capacitance can be measured by Schering bridge.

The EMF of Weston standard cell is measured using

Last Answer : The EMF of Weston standard cell is measured using Potentiometer.

The resistance can be measured most accurately by

Last Answer : The resistance can be measured most accurately by bridge method.

The induction of a high Q inductor can be measured by a

Last Answer : The induction of a high Q inductor can be measured by a Hay Bridge.

The power of a n-phase circuit can be measured by using a minimum of

Last Answer : The power of a n-phase circuit can be measured by using a minimum of (n - 1) wattmeter elements

The frequency can be measured by using:

Last Answer : Weins bridge 

Alternating current is measured by?

Last Answer : Alternating current is measured by induction ammeter.

E.m.f. of a Weston cell is accurately measured by?

Last Answer : E.m.f. of a Weston cell is accurately measured by electrostatic voltmeter.

In an Anderson bridge, the unknown inductance is measured in terms of?

Last Answer : In an Anderson bridge, the unknown inductance is measured in terms of known capacitance and resistance.

A direct current can be measured by?

Last Answer : A direct current can be measured by a D.C. potentiometer in conjunction with a standard resistance.

Resistances can be measured with the help of?

Last Answer : Resistances can be measured with the help of ohmmeters and resistance bridges.

A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the

Description : A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the resolution of the instrument will be (a) 100 mV (b) 99 mV (c) 9 mV (d) 1 mV 

Last Answer : d) 1mV 9.999v÷9999v

In the case of an instrument reading of 8.3 V with a 0 to 150 voltmeter having a guaranteed accuracy of

Description :  In the case of an instrument reading of 8.3 V with a 0 to 150 voltmeter having a guaranteed accuracy of 1% full scale reading, the percentage limiting error is   (A) 1.810% (B) 0.181% (C)12.45% (D) 0.0018%

Last Answer :  In the case of an instrument reading of 8.3 V with a 0 to 150 voltmeter having a guaranteed accuracy of 1% full scale reading, the percentage limiting error is 12.45%

If a DC voltmeter is made from an ammeter having a fed of 100μA then its sensitivity (in KΩ/V) will be

Last Answer :  If a DC voltmeter is made from an ammeter having a fed of 100μA then its sensitivity (in KΩ/V) will be 10.

A 150 V moving iron voltmeter of accuracy class 1.0 reads 75 V when ...

Description : A 150 V moving iron voltmeter of accuracy class 1.0 reads 75 V when used in a circuit under a standard conditions. The maximum possible percentage error in the reading is:

Last Answer : A 150 V moving iron voltmeter of accuracy class 1.0 reads 75 V when used in a circuit under a standard conditions. The maximum possible percentage error in the reading is:  2.0.

The time/div and voltage/div axes of an oscilloscope have been erased. When a 1 kHz, 5V p-p square wave

Description : The time/div and voltage/div axes of an oscilloscope have been erased. When a 1 kHz, 5V p-p square wave calibration pulse is connected to channel 1 ofthe scope the waveform observed on the screen ... channels are the same, the amplitude (pp) and period of the unknown signal are respectively.

Last Answer : The time/div and voltage/div axes of an oscilloscope have been erased. When a 1 kHz, 5V p-p square wave calibration pulse is connected to channel 1 ofthe scope the waveform observed on the screen is ... are the same, the amplitude (pp) and period of the unknown signal are respectively. 7.5 V, 2ms

Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of

Description : Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of frequency in the applied voltage waveform is   (A)sinusoidal (B) square (C) rectangular (D) triangular

Last Answer : Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of frequency in the applied voltage waveform is sinusoidal 

An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic

Description : An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic field having a component along the axis will be  (1) unaffected (2) decreased (3) increased (4) either decreased or increased depending on the direction of the DC field

Last Answer : An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic field having a component along the axis will be either decreased or increased depending on the direction of the DC field

Among the voltages to various electrodes in a CRT the voltage is the highest on

Last Answer : Among the voltages to various electrodes in a CRT the voltage is the highest on PD anode.

If the current in a capacitor leads the voltage by 80°, the loss angle of the capacitor is?

Last Answer : If the current in a capacitor leads the voltage by 80°, the loss angle of the capacitor is 10°.

For measurements on high voltage capacitors, the suitable bridge is?

Last Answer : For measurements on high voltage capacitors, the suitable bridge is Schering bridge.

To measure an A. C. voltage by using an A.C. potentiometer, it is desirable that...

Description : To measure an A. C. voltage by using an A.C. potentiometer, it is desirable that the supply for the potentiometer in taken?

Last Answer : To measure an A. C. voltage by using an A.C. potentiometer, it is desirable that the supply for the potentiometer in taken from the same source as the unknown voltage.

The operating voltage of a meggar is about?

Last Answer : The operating voltage of a meggar is about 100 V.

What is the unit of measure for voltage?

Description : What is the unit of measure for voltage?

Last Answer : Voltage measured in volts.

What equipment is used to measure voltage?

Description : What equipment is used to measure voltage?

Last Answer : Voltmeter is used to measure voltage.

In acoustics, if the volume of the room is 200 m3 then at what frequency the coefficient of absorption is measured? A. 120 kHz B. 120 Hz C. 100 Hz D. 150 Hz

Description : In acoustics, if the volume of the room is 200 m3 then at what frequency the coefficient of absorption is measured? A. 120 kHz B. 120 Hz C. 100 Hz D. 150 Hz

Last Answer : B. 120 Hz

Offsets are measured with an accuracy of 1 in 40. If the point on the paper from both sources of error (due to angular and measurement errors) is not to exceed 0.05 cm on a scale of 1 cm = 20 m, the maximum length of offset should be limited to (A) 14.14 m (B) 28.28 m (C) 200 m (D) None of these

Description : Offsets are measured with an accuracy of 1 in 40. If the point on the paper from both sources of error (due to angular and measurement errors) is not to exceed 0.05 cm on a scale of 1 cm = 20 m, the maximum length of ... should be limited to (A) 14.14 m (B) 28.28 m (C) 200 m (D) None of these

Last Answer : (B) 28.28 m

The emf of a battery is 4.0 V and its internal resistance is `1.5 Omega`. Its potential difference is measured by a voltmeter of resistance `1000 Omeg

Description : The emf of a battery is 4.0 V and its internal resistance is `1.5 Omega`. Its potential difference is measured by a voltmeter of resistance `1000 Omeg

Last Answer : The emf of a battery is 4.0 V and its internal resistance is `1.5 Omega`. Its potential ... percentage error in the reading of emf shown by voltmeter.

Name the quantities which are measured by the following units. (i) Newton (ii) Joule (iii) Watt (iv) Volt (v) Light year (vi) Angstrom (vii) Acre-foot (viii) Becquerel (ix) Hertz (x) Cusec

Description : Name the quantities which are measured by the following units. (i) Newton (ii) Joule (iii) Watt (iv) Volt (v) Light year (vi) Angstrom (vii) Acre-foot (viii) Becquerel (ix) Hertz (x) Cusec

Last Answer : Answers: (i) Force (ii) Work Energy (iii) Power of electricity (iv) Potential difference (v) Distance of stars and planets (vi) Length (vii) Volume (viii) Radioactivity (ix) Frequency (x) Rate of flow of water

For turbulent flow in smooth circular pipe, the velocity distribution is a function of the distance 'd' measured from the wall of the pipe and the friction velocity 'v', and it follows a __________ relationship. (A) Logarithmic (B) Linear (C) Hyperbolic (D) Parabolic

Description : For turbulent flow in smooth circular pipe, the velocity distribution is a function of the distance 'd' measured from the wall of the pipe and the friction velocity 'v', and it follows a __________ relationship. (A) Logarithmic (B) Linear (C) Hyperbolic (D) Parabolic

Last Answer : (A) Logarithmic

Quality of education in a school/college can be measured through v (a) Infrastructural facilities available (b) Manpower, teachers and principal available (c) Students' achievement (d) all of the above

Description : Quality of education in a school/college can be measured through v (a) Infrastructural facilities available (b) Manpower, teachers and principal available (c) Students' achievement (d) all of the above

Last Answer : d) all of the above

Sales for desired profit is measured as A. (Fixed cost + profit)/ (P/V Ratio) B. (Fixed cost + profit) * (P/V Ratio) C. (Fixed cost - profit)/ (P/V Ratio) D. None of the above

Description : Sales for desired profit is measured as A. (Fixed cost + profit)/ (P/V Ratio) B. (Fixed cost + profit) * (P/V Ratio) C. (Fixed cost - profit)/ (P/V Ratio) D. None of the above

Last Answer : A. (Fixed cost + profit)/ (P/V Ratio)

In a series RC circuit, 12 V (rms) is measured across.the resistor and 15 V (rms) is measured across the ...

Description : In a series RC circuit, 12 V (rms) is measured across.the resistor and 15 V (rms) is measured across the capacitor. The value of rms source voltage is: A. 3 V B. 27 V C. 19.2 V D. 1.9 V

Last Answer : In a series RC circuit, 12 V (rms) is measured across.the resistor and 15 V (rms) is measured across the capacitor. The value of rms source voltage is: 19.2 V

What voltage would be measured across the 45 ohm resistor?

Description : What voltage would be measured across the 45 ohm resistor?

Last Answer : Not enough information. But if you know the current, you can useOhm's Law (just multiply the resistance times the current).

If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts

Description : If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts

Last Answer : Answer: A