The B-spline curve has a a.first-order continuity b.second-order continuity c.zero-order continuity d.none of the above

The B-spline curve has a a.first-order continuity b.second-order continuity c.zero-order continuity d.none of the above
by

1 Answer

Answer :

b.second-order continuity
by

Related questions

In synthetic curves, zero-order continuity yields a.a position continuous curve b.a slope continuous curve c.a curvature continuous curve d.none of the above

Description : In synthetic curves, zero-order continuity yields a.a position continuous curve b.a slope continuous curve c.a curvature continuous curve d.none of the above

Last Answer : a.a position continuous curve

In synthetic curves, second-order continuity yields a.a position continuous curve b.a slope continuous curve c.a curvature continuous curve d.none of the above

Description : In synthetic curves, second-order continuity yields a.a position continuous curve b.a slope continuous curve c.a curvature continuous curve d.none of the above

Last Answer : c.a curvature continuous curve

In synthetic curves, first-order continuity yields a.a position continuous curve b.a slope continuous curve c.a curvature continuous curve d.none of the above

Description : In synthetic curves, first-order continuity yields a.a position continuous curve b.a slope continuous curve c.a curvature continuous curve d.none of the above

Last Answer : b.a slope continuous curve

The degree of the curve is independent of the number of control points in _____ a.Hermite cubic spline curve b.Bezier curve c.B-spline curve d.Hyperbola

Description : The degree of the curve is independent of the number of control points in _____ a.Hermite cubic spline curve b.Bezier curve c.B-spline curve d.Hyperbola

Last Answer : c.B-spline curve

________curves allow local control of the curve. a.Analytical b.Hermite cubic spline c.Beizer d.B-Spline

Description : ________curves allow local control of the curve. a.Analytical b.Hermite cubic spline c.Beizer d.B-Spline

Last Answer : d.B-Spline

The Bezier curve is smoother than the Hermite cubic spline because it has _________ orderderivatives. a.lower b.higher c.lower and higher both d.none of the above

Description : The Bezier curve is smoother than the Hermite cubic spline because it has _________ orderderivatives. a.lower b.higher c.lower and higher both d.none of the above

Last Answer : b.higher

To determine the coefficients of the equation – two end-points and the two tangentvectors. This statement is true for which of the following? a.B-spline curve b.Hermite Cubic Spline Curve c.Beizer curve d.none of the above

Description : To determine the coefficients of the equation – two end-points and the two tangentvectors. This statement is true for which of the following? a.B-spline curve b.Hermite Cubic Spline Curve c.Beizer curve d.none of the above

Last Answer : b.Hermite Cubic Spline Curve

Find parametric equation for Y-coordinates of Hermite cubic spline curve having endpoints P0[4,4]; P1[8,5] a.2u3-3u2+2u+4 b.3u3-2u2-2u-4 c.2u3-3u2-2u-4 d.2u3+3u2+2u+4

Description : Find parametric equation for Y-coordinates of Hermite cubic spline curve having endpoints P0[4,4]; P1[8,5] a.2u3-3u2+2u+4 b.3u3-2u2-2u-4 c.2u3-3u2-2u-4 d.2u3+3u2+2u+4

Last Answer : a.2u3-3u2+2u+4

Find parametric equation for X-coordinates of hermite cubic spline curve having endpoints P0[4,4]; P1[8,5] a.-5u3+8u2+u+1 b.5u3+8u2+u+1 c.8u3-5u2-u+1 d.8u3+5u2+u+1

Description : Find parametric equation for X-coordinates of hermite cubic spline curve having endpoints P0[4,4]; P1[8,5] a.-5u3+8u2+u+1 b.5u3+8u2+u+1 c.8u3-5u2-u+1 d.8u3+5u2+u+1

Last Answer : a.-5u3+8u2+u+1

The degree of the curve is independent of the number of control points in . a.Hermite cubic spline curve b.Bezier curve c.B-spline curve d.Hyperbola

Description : The degree of the curve is independent of the number of control points in . a.Hermite cubic spline curve b.Bezier curve c.B-spline curve d.Hyperbola

Last Answer : c.B-spline curve

The number of control points can be added orsubtracted in . a.Bezier curve b.B-spline curve c.Cubic spline curve d.all of the above

Description : The number of control points can be added orsubtracted in . a.Bezier curve b.B-spline curve c.Cubic spline curve d.all of the above

Last Answer : b.B-spline curve

To determine the coefficients of the equation – two end-points and the two tangentvectors. This statement is true for which of the following a.B-spline curve b.Hermite Cubic Spline Curve c.Beizer curve d.none of the above

Description : To determine the coefficients of the equation – two end-points and the two tangentvectors. This statement is true for which of the following a.B-spline curve b.Hermite Cubic Spline Curve c.Beizer curve d.none of the above

Last Answer : b.Hermite Cubic Spline Curve

curves allow local control of the curve a.Analytical b.Hermite cubic spline c.Beizer d.B-Spline

Description : curves allow local control of the curve a.Analytical b.Hermite cubic spline c.Beizer d.B-Spline

Last Answer : d.B-Spline

The curve that follows a convex hull property is: a.Cubic spline b.B-spline c.Bezier curve d.Both (b) and (c)

Description : The curve that follows a convex hull property is: a.Cubic spline b.B-spline c.Bezier curve d.Both (b) and (c)

Last Answer : b.B-spline

Which of the following is not a synthetic entity? a.Hyperbola b.Bezier curve c.B-spline curve d.Cubic spline curve

Description : Which of the following is not a synthetic entity? a.Hyperbola b.Bezier curve c.B-spline curve d.Cubic spline curve

Last Answer : a.Hyperbola

The degree of the B-spline with varying knot vectors a.Increases with knot vectors b.Decreases with knot vectors c.Remains constant d.none of the above

Description : The degree of the B-spline with varying knot vectors a.Increases with knot vectors b.Decreases with knot vectors c.Remains constant d.none of the above

Last Answer : a.Increases with knot vectors

Which of the following is not an analytical entity? a.Line b.Circle c.Spline d.Parabola

Description : Which of the following is not an analytical entity? a.Line b.Circle c.Spline d.Parabola

Last Answer : c.Spline

C” continuity refers to a.Common tangent b.Common curvature c.Common point d.Common normal

Description : C” continuity refers to a.Common tangent b.Common curvature c.Common point d.Common normal

Last Answer : a.Common tangent

C‘ continuity refers to a.Common tangent b.Common curvature c.Common point d.Common normal

Description : C‘ continuity refers to a.Common tangent b.Common curvature c.Common point d.Common normal

Last Answer : b.Common curvature

C0 continuity refers to a.Common tangent b.Common curvature c.Common point d.Common normal

Description : C0 continuity refers to a.Common tangent b.Common curvature c.Common point d.Common normal

Last Answer : c.Common point

In the bezier curve, the curve is always________to first and last segments of the polygon a.normal b.parallel c.tangent d.none of the above

Description : In the bezier curve, the curve is always________to first and last segments of the polygon a.normal b.parallel c.tangent d.none of the above

Last Answer : c.tangent

In the bezier curve, the curve is always to first and last segments of thepolygon a.normal b.parallel c.tangent d.none of the above

Description : In the bezier curve, the curve is always to first and last segments of thepolygon a.normal b.parallel c.tangent d.none of the above

Last Answer : c.tangent

In modeling of a tabulated cylinder, the plane of the curve is _______ a.along the curve b.normal to the curve c.along the axis of the cylinder d.perpendicular to the axis of the cylinder

Description : In modeling of a tabulated cylinder, the plane of the curve is _______ a.along the curve b.normal to the curve c.along the axis of the cylinder d.perpendicular to the axis of the cylinder

Last Answer : d.perpendicular to the axis of the cylinder

In Beizer Curve, the flexibility of the shape would increase with _______ of the polygon. a.decrease in the number of vertices b.increase in the number of vertices c.decrease in control points d.none of the above

Description : In Beizer Curve, the flexibility of the shape would increase with _______ of the polygon. a.decrease in the number of vertices b.increase in the number of vertices c.decrease in control points d.none of the above

Last Answer : b.increase in the number of vertices

In Beizer Curve, the curve follows __________ a.the control points b.the shape of the defining polygon c.the defining points d.none of the above

Description : In Beizer Curve, the curve follows __________ a.the control points b.the shape of the defining polygon c.the defining points d.none of the above

Last Answer : b.the shape of the defining polygon

The parabola is defined mathematically as a curve generated by a point that moves suchthat its distance from the focus is always__________the distance to the directrix a.larger than b.smaller than c.equal to d.none of the above

Description : The parabola is defined mathematically as a curve generated by a point that moves suchthat its distance from the focus is always__________the distance to the directrix a.larger than b.smaller than c.equal to d.none of the above

Last Answer : c.equal to

Mathematically, the ellipse is a curve generated by a point moving in space such that atany position the sum of its distances from two fixed points (foci) is constant and equal to a.the major diameter b.the minor diameter c.semi major diameter d.semi-minor diameter

Description : Mathematically, the ellipse is a curve generated by a point moving in space such that atany position the sum of its distances from two fixed points (foci) is constant and equal to a.the major diameter b.the minor diameter c.semi major diameter d.semi-minor diameter

Last Answer : a.the major diameter

Synthetic curve pass through defined data points and thus can be represented by a.polynomial equations b.exponential equations c.partial differential equations d.differential equations

Description : Synthetic curve pass through defined data points and thus can be represented by a.polynomial equations b.exponential equations c.partial differential equations d.differential equations

Last Answer : a.polynomial equations

When a smooth curve is approximated through the data points, then the curve is knownas a.approximation curve b.pitch curve c.data curve d.interpolant curve

Description : When a smooth curve is approximated through the data points, then the curve is knownas a.approximation curve b.pitch curve c.data curve d.interpolant curve

Last Answer : a.approximation curve

When the curve passes through all the data points, then the curve is known as a.approximation curve b.pitch curve c.data curve d.interpolant curve

Description : When the curve passes through all the data points, then the curve is known as a.approximation curve b.pitch curve c.data curve d.interpolant curve

Last Answer : d.interpolant curve

Which of the following is not a method to describe a curve mathematically? a.Explicit form b.Laplace form c.Implicit form d.Parametric form

Description : Which of the following is not a method to describe a curve mathematically? a.Explicit form b.Laplace form c.Implicit form d.Parametric form

Last Answer : b.Laplace form

The curve is defined as the locus of a point moving with _ degree of freedom a.0 b.1 c.2 d.3

Description : The curve is defined as the locus of a point moving with _ degree of freedom a.0 b.1 c.2 d.3

Last Answer : b.1

In Beizer Curve, the flexibility of the shape would increase with a.decrease in the number of vertices b.increase in the number of vertices c.decrease in control points d.none of the above

Description : In Beizer Curve, the flexibility of the shape would increase with a.decrease in the number of vertices b.increase in the number of vertices c.decrease in control points d.none of the above

Last Answer : b.increase in the number of vertices

In Beizer Curve, the curve follows a.the control points b.the shape of the defining polygon c.the defining points d.none of the above

Description : In Beizer Curve, the curve follows a.the control points b.the shape of the defining polygon c.the defining points d.none of the above

Last Answer : b.the shape of the defining polygon

When a smooth curve is approximated through the data points, then the curve isknown as a.interpolant curve b.approximation curve c.pitch curve d.data curve

Description : When a smooth curve is approximated through the data points, then the curve isknown as a.interpolant curve b.approximation curve c.pitch curve d.data curve

Last Answer : b.approximation curve

Mathematically, the ellipse is a curve generated by a point moving in space such thatat any position the sum of its distances from two fixed points (foci) is constant and equal to a.the major diameter b.the minor diameter c.semi major diameter d.semi-minor diameter

Description : Mathematically, the ellipse is a curve generated by a point moving in space such thatat any position the sum of its distances from two fixed points (foci) is constant and equal to a.the major diameter b.the minor diameter c.semi major diameter d.semi-minor diameter

Last Answer : a.the major diameter

The degree of the Bezier curve with n control points is a.n + 1 b.n - 1 c.n d.2n

Description : The degree of the Bezier curve with n control points is a.n + 1 b.n - 1 c.n d.2n

Last Answer : a.n + 1

The shape of Bezier curve is controlled by a.Control points b.Knots c.End points d.All the above

Description : The shape of Bezier curve is controlled by a.Control points b.Knots c.End points d.All the above

Last Answer : a.Control points

To indicate the position of the workpiece ly & easily machine zero pint should be displacedto another point on the workpiece called… a.Workpiece zero Point b.machine Zero Point c.Start Point d.Program Zero point

Description : To indicate the position of the workpiece ly & easily machine zero pint should be displacedto another point on the workpiece called… a.Workpiece zero Point b.machine Zero Point c.Start Point d.Program Zero point

Last Answer : a.Workpiece zero Point

……… is the origin of the coordinate system which is defined by manufacturer they cannotbe changed a.Blocking Point b.machine Zero Point c.Start Point d.Program Zero point

Description : ……… is the origin of the coordinate system which is defined by manufacturer they cannotbe changed a.Blocking Point b.machine Zero Point c.Start Point d.Program Zero point

Last Answer : b.machine Zero Point

An absolute NC system is one in which all position coordinates are referred to one fixedorigin called the zero point. a.TRUE b.FALSE c. d.

Description : An absolute NC system is one in which all position coordinates are referred to one fixedorigin called the zero point. a.TRUE b.FALSE c. d.

Last Answer : a.TRUE

In penalty approach, rigid support is considered as a spring having stiffness. a.zero b.very small c.very large d.infinite

Description : In penalty approach, rigid support is considered as a spring having stiffness. a.zero b.very small c.very large d.infinite

Last Answer : d.infinite

The characteristic of the shape function is a.the shape function has a unit value at one nodal point and zero value at the other nodes b.the sum of the shape function is equal to one c.both a & b d.None of the above

Description : The characteristic of the shape function is a.the shape function has a unit value at one nodal point and zero value at the other nodes b.the sum of the shape function is equal to one c.both a & b d.None of the above

Last Answer : c.both a & b

When a thin plate is subjected to loading in its own plane only, the condition is called _ a.plane stress b.plane strain c.zero stress d.zero strain

Description : When a thin plate is subjected to loading in its own plane only, the condition is called _ a.plane stress b.plane strain c.zero stress d.zero strain

Last Answer : a.plane stress

Transpose of a column matrix is a.Zero matrix b.Identity matrix c.Row matrix d.Diagonal matrix

Description : Transpose of a column matrix is a.Zero matrix b.Identity matrix c.Row matrix d.Diagonal matrix

Last Answer : c.Row matrix

In homogeneous coordinates value of ‘h’ is consider as 1 & it is called….. a.Magnitude Vector b.Unit Vector c.Non-Zero Vector d.Non-Zero Scalar Factor

Description : In homogeneous coordinates value of ‘h’ is consider as 1 & it is called….. a.Magnitude Vector b.Unit Vector c.Non-Zero Vector d.Non-Zero Scalar Factor

Last Answer : d.Non-Zero Scalar Factor

In a simple and visual method of Cell design, the priorities in classifying may be in the order a.Rotational or non rotational – Material – Size – Shape b.Material – Rotational or non rotational – Size – Shape c.Size – Rotational or non rotational – Material – Shape d.Shape – Rotational or non rotational – Material – Size

Description : In a simple and visual method of Cell design, the priorities in classifying may be in the order a.Rotational or non rotational †Material †Size †Shape b.Material †Rotational or non ... non rotational †Material †Shape d.Shape †Rotational or non rotational †Material †Size

Last Answer : a.Rotational or non rotational – Material – Size – Shape

If the structure is more complex in order to simplify the model, we need to subdividethe structure into substructures. These substructures are termed as . a.elements b.modules c.links d.models

Description : If the structure is more complex in order to simplify the model, we need to subdividethe structure into substructures. These substructures are termed as . a.elements b.modules c.links d.models

Last Answer : b.modules

For 1-D bar elements if the structure is having 3 nodes then the stiffness matrix formed ishaving an order of a.2*2 b.3*3 c.4*4 d.6*6

Description : For 1-D bar elements if the structure is having 3 nodes then the stiffness matrix formed ishaving an order of a.2*2 b.3*3 c.4*4 d.6*6

Last Answer : b.3*3

Panning is a technique in which users can change the size of the area to beviewed in order to see more detail or less detail. a.TRUE b.FALSE c. d.

Description : Panning is a technique in which users can change the size of the area to beviewed in order to see more detail or less detail. a.TRUE b.FALSE c. d.

Last Answer : b.FALSE