Description : In Beizer Curve, the curve follows a.the control points b.the shape of the defining polygon c.the defining points d.none of the above
Last Answer : b.the shape of the defining polygon
Description : In Beizer Curve, the flexibility of the shape would increase with _______ of the polygon. a.decrease in the number of vertices b.increase in the number of vertices c.decrease in control points d.none of the above
Last Answer : b.increase in the number of vertices
Description : In Beizer Curve, the flexibility of the shape would increase with a.decrease in the number of vertices b.increase in the number of vertices c.decrease in control points d.none of the above
Description : To determine the coefficients of the equation – two end-points and the two tangentvectors. This statement is true for which of the following? a.B-spline curve b.Hermite Cubic Spline Curve c.Beizer curve d.none of the above
Last Answer : b.Hermite Cubic Spline Curve
Description : To determine the coefficients of the equation – two end-points and the two tangentvectors. This statement is true for which of the following a.B-spline curve b.Hermite Cubic Spline Curve c.Beizer curve d.none of the above
Description : ________curves allow local control of the curve. a.Analytical b.Hermite cubic spline c.Beizer d.B-Spline
Last Answer : d.B-Spline
Description : curves allow local control of the curve a.Analytical b.Hermite cubic spline c.Beizer d.B-Spline
Description : The shape of Bezier curve is controlled by a.Control points b.Knots c.End points d.All the above
Last Answer : a.Control points
Description : QFor generating Coons patch we require a.A set of grid points on surface b.A set of control points c.Four bounding curves defining surface d.Two bounding curves and a set of grid control points
Last Answer : c.Four bounding curves defining surface
Description : In the bezier curve, the curve is always________to first and last segments of the polygon a.normal b.parallel c.tangent d.none of the above
Last Answer : c.tangent
Description : Scaling of a polygon is done by computing a.The product of (x, y) of each vertex b.(x, y) of end points c.Center coordinates d.Only a
Last Answer : d.Only a
Description : The curve that follows a convex hull property is: a.Cubic spline b.B-spline c.Bezier curve d.Both (b) and (c)
Last Answer : b.B-spline
Description : The degree of the curve is independent of the number of control points in _____ a.Hermite cubic spline curve b.Bezier curve c.B-spline curve d.Hyperbola
Last Answer : c.B-spline curve
Description : The degree of the curve is independent of the number of control points in . a.Hermite cubic spline curve b.Bezier curve c.B-spline curve d.Hyperbola
Description : The number of control points can be added orsubtracted in . a.Bezier curve b.B-spline curve c.Cubic spline curve d.all of the above
Last Answer : b.B-spline curve
Description : The degree of the Bezier curve with n control points is a.n + 1 b.n - 1 c.n d.2n
Last Answer : a.n + 1
Description : What is the rectangle in the world defining the region that is to be displayed? a.World co-ordinate system b.Screen co-ordinate system c.World window d.Interface window
Last Answer : c.World window
Description : Mathematically, the ellipse is a curve generated by a point moving in space such that atany position the sum of its distances from two fixed points (foci) is constant and equal to a.the major diameter b.the minor diameter c.semi major diameter d.semi-minor diameter
Last Answer : a.the major diameter
Description : Synthetic curve pass through defined data points and thus can be represented by a.polynomial equations b.exponential equations c.partial differential equations d.differential equations
Last Answer : a.polynomial equations
Description : When a smooth curve is approximated through the data points, then the curve is knownas a.approximation curve b.pitch curve c.data curve d.interpolant curve
Last Answer : a.approximation curve
Description : When the curve passes through all the data points, then the curve is known as a.approximation curve b.pitch curve c.data curve d.interpolant curve
Last Answer : d.interpolant curve
Description : When a smooth curve is approximated through the data points, then the curve isknown as a.interpolant curve b.approximation curve c.pitch curve d.data curve
Last Answer : b.approximation curve
Description : Mathematically, the ellipse is a curve generated by a point moving in space such thatat any position the sum of its distances from two fixed points (foci) is constant and equal to a.the major diameter b.the minor diameter c.semi major diameter d.semi-minor diameter
Description : __________ is one where mechanical forces or restricting forms are applied on a material so asto form it into the desired shape a.Subtractive process b.Additive process c.Formative process d.All of above
Last Answer : c.Formative process
Description : In modeling of a tabulated cylinder, the plane of the curve is _______ a.along the curve b.normal to the curve c.along the axis of the cylinder d.perpendicular to the axis of the cylinder
Last Answer : d.perpendicular to the axis of the cylinder
Description : The Bezier curve is smoother than the Hermite cubic spline because it has _________ orderderivatives. a.lower b.higher c.lower and higher both d.none of the above
Last Answer : b.higher
Description : The B-spline curve has a a.first-order continuity b.second-order continuity c.zero-order continuity d.none of the above
Last Answer : b.second-order continuity
Description : In synthetic curves, first-order continuity yields a.a position continuous curve b.a slope continuous curve c.a curvature continuous curve d.none of the above
Last Answer : b.a slope continuous curve
Description : In synthetic curves, zero-order continuity yields a.a position continuous curve b.a slope continuous curve c.a curvature continuous curve d.none of the above
Last Answer : a.a position continuous curve
Description : The parabola is defined mathematically as a curve generated by a point that moves suchthat its distance from the focus is always__________the distance to the directrix a.larger than b.smaller than c.equal to d.none of the above
Last Answer : c.equal to
Description : Which of the following is not a method to describe a curve mathematically? a.Explicit form b.Laplace form c.Implicit form d.Parametric form
Last Answer : b.Laplace form
Description : Find parametric equation for Y-coordinates of Hermite cubic spline curve having endpoints P0[4,4]; P1[8,5] a.2u3-3u2+2u+4 b.3u3-2u2-2u-4 c.2u3-3u2-2u-4 d.2u3+3u2+2u+4
Last Answer : a.2u3-3u2+2u+4
Description : Find parametric equation for X-coordinates of hermite cubic spline curve having endpoints P0[4,4]; P1[8,5] a.-5u3+8u2+u+1 b.5u3+8u2+u+1 c.8u3-5u2-u+1 d.8u3+5u2+u+1
Last Answer : a.-5u3+8u2+u+1
Description : The curve is defined as the locus of a point moving with _ degree of freedom a.0 b.1 c.2 d.3
Last Answer : b.1
Description : In synthetic curves, second-order continuity yields a.a position continuous curve b.a slope continuous curve c.a curvature continuous curve d.none of the above
Last Answer : c.a curvature continuous curve
Description : In the bezier curve, the curve is always to first and last segments of thepolygon a.normal b.parallel c.tangent d.none of the above
Description : Which of the following is not a synthetic entity? a.Hyperbola b.Bezier curve c.B-spline curve d.Cubic spline curve
Last Answer : a.Hyperbola
Description : Digit 5 in Opitz system is for_________ a.Part class b.Main shape c.Additional holes, teeth and forming d.Plane surface machining
Last Answer : c.Additional holes, teeth and forming
Description : Digit 4 in Opitz system is for_________ a.Part class b.Main shape c.Rotational machining d.Plane surface machining
Last Answer : d.Plane surface machining
Description : Digit 3 in Opitz system is for_________ a.Part class b.Main shape c.Rotational machining d.Plane surface machining
Last Answer : c.Rotational machining
Description : Digit 2 in Opitz system is for_________ a.Part class b.Main shape c.Rotational machining d.Plane surface machining
Last Answer : b.Main shape
Description : Digit 1 in Opitz system is for_________ a.Part class b.Main shape c.Rotational machining d.Plane surface machining
Last Answer : a.Part class
Description : Which of the following technique of grouping does not consider the design and shape aspect? a.A simple and visual method of cell design b.Family formation by classification and codification c.Cell formation using Production Flow Analysis d.All of the above
Last Answer : c.Cell formation using Production Flow Analysis
Description : In Opitz system, 2nd digit indicates a.Type and Shape b.External shape and external shape elements c.External plane surface finishing d.Auxiliary hole and gear teeth
Last Answer : b.External shape and external shape elements
Description : In a simple and visual method of Cell design, the priorities in classifying may be in the order a.Rotational or non rotational †Material †Size †Shape b.Material †Rotational or non ... non rotational †Material †Shape d.Shape †Rotational or non rotational †Material †Size
Last Answer : a.Rotational or non rotational – Material – Size – Shape
Description : In the ___________ process, one starts with a single block of solid material larger than the finalsize of the desired object and material is removed until the desired shape is reached. a.Subtractive process b.Additive process c.Formative process d.All of above
Last Answer : a.Subtractive process
Description : The characteristic of the shape function is a.the shape function has a unit value at one nodal point and zero value at the other nodes b.the sum of the shape function is equal to one c.both a & b d.None of the above
Last Answer : c.both a & b
Description : are used to express the geometry or shape of theelement a.Mode shapes b.Shape functions c.Natural curves d.None of the above
Last Answer : b.Shape functions
Description : is defined as the ratio of the largest dimension of theelement to the smallest dimension. a.Element depth ratio b.Mode shape ratio c.Aspect ratio d.None of the above
Last Answer : c.Aspect ratio
Description : To find the nodal displacements in all parts of the element, are used. a.shape function b.node function c.element function d.coordinate function
Last Answer : a.shape function