Description : The rotary and oscillating tool which does not turn the soil upside down is a) Power tiller b) Rotravator c) Power harrow d) Treader and rotary tiller
Last Answer : c) Power harrow
Description : A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above
Last Answer : D. All of the above
Description : Rotary tiller are wide adopted in rice cultivation due to a) Excessive pulverization b) Suitability for pudding paddy field c) Reduced draft requirement d) Complete inversion of soil
Last Answer : b) Suitability for pudding paddy field
Description : A power tiller is most suited for : A. Draft operation with rigid tools B. Rotary cultivation C. Stationary operation D. Transport work
Last Answer : B. Rotary cultivation
Description : A power tiller is relatively more suitable for : A. Puddling of low land paddy fields with a rotary tiller B. Primary tillage of upland paddy fields with a rotary tillers C. Primary tillage with a mould board plough D. Farm transportation work
Last Answer : A. Puddling of low land paddy fields with a rotary tiller
Description : owest specific energy requirement for the operation of rotavator is about _______ times as great as a mould board plough working in the same soil. a) Equal b) Twice c) Three d) Four
Last Answer : c) Three
Description : Optimum operating speed of rotavator is a)20-150rpm b)150-350rpm c)350-500rpm d) >500rpm
Last Answer : d) >500rpm
Description : For operating rotavator on trashy soils which tines are better: A L-shaped B.Hook shaped C.Backward curved tip twist blade D.Straight blade
Last Answer : A L-shaped
Description : One operation of rotavator dose a job equivalent to a) One ploughing + two harrowing b) One harrowing + two ploughing c) One ploughing only d) One harrowing only
Last Answer : a) One ploughing + two harrowing
Description : .Laying out of field in lands is essential when working with a. Two way plough b. One way plough c. Disc harrow d. Cultivator
Last Answer : b. One way plough
Description : GOOD EARTH is one of the important make of (A) tractor (B) electric motor (C) diesel engine (D)power tiller
Last Answer : A) tractor
Description : is the prime mover in which the direction of travel and its control for field operation is performed by the operator walking behind it. A. Power tiller C. Tillage B. Disc plough D. Rotary tiller
Last Answer : Power tiller
Description : Scouring will occur as long as a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face b) Frictional resistance at soil tool interface is more than ... c) Soil-metal friction is more than angle of soil shearing resistance d) None of the above
Last Answer : a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face
Description : is the mechanical manipulation of soil to provide favorable condition for crop production. A. Power tiller C. Rotary tiller B. Tillage D. Disc plough
Last Answer : Tillage
Description : Which of the following is not a tractor drawn primary tillage tool? 1. Disc plough 2. rotavator 3. Country plough 4. Bar harrow
Last Answer : ans 3
Description : The implement which can work in offset position a)offset disc harrow b) mower c) both (a) and (b) d) none of the above
Last Answer : c) both (a) and (b)
Description : In an offset disc harrow the angle between two gang is a) less than 90 degree b) 90 degree c) greater than 90 degree d) 180degree
Last Answer : a) less than 90 degre
Description : n single action disc harrow the two gangs are at set single a) less than 90 degree b) at 90 degree c) greater than 90 degree d) at 180 degree
Last Answer : c) greater than 90 degree
Description : Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front
Last Answer : a) Concave
Description : For maximum moisture conservation ploughing is done with A. mb plough b. cultivator c. chisel plough d. dice harrow
Last Answer : c. chisel plough
Description : The depth of penetration of a disc harrow is increased by: a) Tilt angle b) Gang angle c) Disc angle d) All of above
Last Answer : b) Gang angle
Description : The two primery tillage equipment a. MB plough and disc harrow b. Disc plough and disc harrow c. Disc harrow and cultivetor d. MB plough and subsoiler
Last Answer : d. MB plough and subsoiler
Description : Dead furrow is made by: a. One way MB plough b. Two way MB plough c. Ridger d. Disc harrow
Last Answer : a. One way MB plough
Description : A coulter attachment is used with: a. Disc harrow b. Seed drill c. MB plough d. Sub soiler
Last Answer : c. MB ploug
Description : .Land shipping become necessary often the following implments is used: a. MB plough b. Disc harrow c. Cultivator d. All of these
Last Answer : a. MB plough
Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc Harrow c) Cultivator d) All of the above
Last Answer : a) M.B. Plough
Description : Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front
Description : Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front
Last Answer : c) concave, convex
Description : Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true
Last Answer : d) Both (b) and (c) are true
Description : Rotary tillers are characterized by a) Lower and negative draft b) High power requirement c) Excessive pulverization d) All the above
Last Answer : d) All the above
Description : pecific energy requirement of rotary tillers can be reduce by a) Increasing the bite length b) Decreasing depth to diameter ratio c) Both (a) and (b) d) Excessive reduction in total power requirement
Last Answer : c) Both (a) and (b)
Description : The power tiller harrow is a mounted reciprocating comb type. A. Rear C. Right B. Front. D. None of the above
Last Answer : rear
Description : This type blades in rotary tiller are more effective in cutting weeds and they do not Pulverize the soil much. b. twisted c. straight d. None of the above
Last Answer : Ans- a. ‘L’
Description : For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these
Last Answer : D)all of these
Description : Closer group spacing and accurate hill spacing is obtained with a) Rotary valve b) Transfer wheel c)Both a & b d)All of the above
Last Answer : c)Both a & b
Description : V-shaped sweeps are best suited for a ) Primary tillage b) Stubble mulch tillage c) Rotary tillage d) Minimum tillage
Last Answer : b) Stubble mulch tillage
Description : Subsoiler plough is best suited for a. breaking hard pan b. deep ploughing c. making ditches d. inter cultivation
Last Answer : a. breaking hard pan
Description : Disc angle adjustment influences: a. Depth of cut b. width of cut c. Soil break up d. Direction of travel
Last Answer : b. width of cut
Description : Formula for adding weight (ballast) on tractor tyres working in loose wet soil for good traction a)(km/hr × kg/PTO kw)=540 b)( km/hr × kg/PTO kw)=670 c)( km/hr × kg/PTO HP)=540 d)( km/hr × kg/PTO HP)=670
Last Answer : a)(km/hr × kg/PTO kw)=540
Description : shaped blades are best suited for i. Minimum tillage of trashy land at shallow depths j. Dried hard soils k. Cutting and pulverisation in wet sticky clay soil l. Working under normal field conditions
Last Answer : i. Minimum tillage of trashy land at shallow depths
Description : Hook type blades best suited for e. Minimum tillage of trashy land at shallow depths f. Dried hard soils g. Cutting and pulverisation especially in wet sticky clay soil h. Working under normal field conditions
Last Answer : f. Dried hard soils
Description : _______ designates the shape of gross peripheral and cross-sectional boundaries of the soil working tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape
Last Answer : c) Edge shape
Description : Soil acceleration increases draft because of a) Increased normal load on soil working surface b) Increased frictional resistance c) Kinetic energy imparted to the soil d) All of the above
Last Answer : d) All of the above
Description : raft increases with increase in forward speed for most of the implement, mainly due to a) More rapid acceleration of any soil particles that is moved appreciably b) More working width c) Increased working depth d) Draft decreases with increase in speed of implement
Last Answer : a) More rapid acceleration of any soil particles that is moved appreciably
Description : This type blades in rotary tiller are Suitable for deep tillage in relatively clean ground, but clogging and wrapping of trashes on the tynes and shafts. a. L c. straight d. None of the above
Last Answer : Ans- b. twisted
Description : The following types of blades are used with the rotor in rotary tiller a. ‗L‘ type blade c) both A & B b. Twisted blade d) chisel plough
Last Answer : both A & B
Description : An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above
Last Answer : d) None of the above
Description : illage tool moving with uniform velocity is subjected to A)force of gravity. B)pull of power source C)soil reaction. D)all of the above
Last Answer : D)all of the above
Description : Gears are used for: a)changing the speed rotation b)changing direction of rotation c)changing direction of shafting d)all of the above
Last Answer : d)all of the above
Description : Vetical suction of plough influences: a. Pulverization b. Depth of cut c. Width of cut d. Direction of cut
Last Answer : b. Depth of cut