Description : Vetical suction of plough influences: a. Pulverization b. Depth of cut c. Width of cut d. Direction of cut
Last Answer : b. Depth of cut
Description : Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle
Last Answer : a)Increasing disc angle
Description : The depth of penetration of a disc harrow is increased by: a) Tilt angle b) Gang angle c) Disc angle d) All of above
Last Answer : b) Gang angle
Description : Vertical section of plough influences 1. Pulverization 2. Depth of cut 3. Width of cut 4. direction of pull
Last Answer : ans 2
Description : Vertical section of plough influences A. Pulverization C. Width of cut B. Depth of cut D. Direction of pull
Last Answer : Depth of cut
Description : Size of MB plow is determined by (a) depth of cut (b) width of cut (c) number of accessories (d) none of the above
Last Answer : (b) width of cut
Description : raft increases with increase in forward speed for most of the implement, mainly due to a) More rapid acceleration of any soil particles that is moved appreciably b) More working width c) Increased working depth d) Draft decreases with increase in speed of implement
Last Answer : a) More rapid acceleration of any soil particles that is moved appreciably
Description : The adjustment in MB plough for increasing the depth of operation a) Vertical suction b) Horizontal suction c) Gang angle d) Disc angle Ans. a
Last Answer : ans a
Description : In an offset disc harrow the angle between two gang is a) less than 90 degree b) 90 degree c) greater than 90 degree d) 180degree
Last Answer : a) less than 90 degre
Description : In a disc plough with the increase in the disk angle, the transverse component of reaction will a)Increase b) Decrease c) Unaffected d) None of the above
Last Answer : a)Increase
Description : Penetration of disc plough can be improved by a) Increase disc angle b) Decreasing tilt angle c) Both (a) and (b) d) None of the above
Last Answer : b) Decreasing tilt angle
Description : Disc type furrow openers are especially suited to A. Stoney and root infested soils B. Poorly prepared bed in trashy soil C. Hard and sticky soil with considerable amount of debris and mulch D. All of the above
Last Answer : C. Hard and sticky soil with considerable amount of debris and mulch
Description : At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above
Last Answer : a) Greater contact area between furrow wall and the convex side of the disc
Description : Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder
Last Answer : a.) Decreasing cylinder peripheral speed.
Description : Durability of the fertilizer increases with a) Increase in the kinetic angle of repose b) Decrease in the kinetic angle of repose c) Decrease in the speed of the forward travel d) None of the above
Last Answer : b) Decrease in the kinetic angle of repose
Description : Rotavator working in reverse direction for compacting soil and giving good touch to inter culturing is called a) Rotary tiller b) Power tiller c) Power harrow d) Treader
Last Answer : d) Treader
Description : .Large tilt angle best for a) Hard soil b) Sticky and non-scouring soil c) Dry and cemented soil d None of the above
Last Answer : b) Sticky and non-scouring soil
Description : Scouring will occur as long as a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face b) Frictional resistance at soil tool interface is more than ... c) Soil-metal friction is more than angle of soil shearing resistance d) None of the above
Last Answer : a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face
Description : 1Heavy draft of a disc plough is due to: A. Blunt disc B. Furrows too wide C. Loose bearings D. All are currect
Last Answer : D. All are currect
Description : The implement which can work in offset position a)offset disc harrow b) mower c) both (a) and (b) d) none of the above
Last Answer : c) both (a) and (b)
Description : n single action disc harrow the two gangs are at set single a) less than 90 degree b) at 90 degree c) greater than 90 degree d) at 180 degree
Last Answer : c) greater than 90 degree
Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc plough c) Cultivator d) All of the above
Last Answer : a) M.B. Plough
Description : Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front
Last Answer : a) Concave
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill
Last Answer : a) Raspbar type cylinder
Description : 0ff-set disc harrows are best suitable to work for a) primary implement b) breaking clods c) orchard cultivation d) surface finishing
Last Answer : c) orchard cultivation
Description : In standard disc plow the tilk angel varies between: A.30-40 ° B.40-45° C.20-25° D.2-3°
Last Answer : C.20-25°
Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails
Last Answer : c) Spike tooth and hammer mill
Description : The two primery tillage equipment a. MB plough and disc harrow b. Disc plough and disc harrow c. Disc harrow and cultivetor d. MB plough and subsoiler
Last Answer : d. MB plough and subsoiler
Description : Dead furrow is made by: a. One way MB plough b. Two way MB plough c. Ridger d. Disc harrow
Last Answer : a. One way MB plough
Description : A coulter attachment is used with: a. Disc harrow b. Seed drill c. MB plough d. Sub soiler
Last Answer : c. MB ploug
Description : .Land shipping become necessary often the following implments is used: a. MB plough b. Disc harrow c. Cultivator d. All of these
Last Answer : a. MB plough
Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc Harrow c) Cultivator d) All of the above
Description : Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill
Description : Heavy draft of a disc plough is due to: a) Blunt disc b) Furrows too wide c) Loose bearings d) All of the above
Last Answer : d) All of the above
Description : One of the main advantages of disc brakes over drum brakes is that the disc brake : U. Can stop a vehicle in a shorter distance V. Is more heat resistant W. Weighs less than drum brakes X. Requires less pedal force to stop the vehicle
Last Answer : . Requires less pedal force to stop the vehicle
Description : The type of bearing generally used to support the discs on a standard disc plough is: A. Ball bearing. B. Tapered roller bearing. C. Plain roller bearing. D. Bush bearing.
Last Answer : B. Tapered roller bearing.
Description : .Laying out of field in lands is essential when working with a. Two way plough b. One way plough c. Disc harrow d. Cultivator
Last Answer : b. One way plough
Description : Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front
Last Answer : c) concave, convex
Description : Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true
Last Answer : d) Both (b) and (c) are true
Description : Vertical section of plough influence A. Pulverisation B. Depth of cut C. Width of cut. D. Direction of pull
Last Answer : Pulverisation
Description : The size of a seed rill is expressed by: A. Amount of seed sown per unit time. B. Length x width of the machine. C. Area covered per unit time. D. The number of furrow openers x distance between two furrow
Last Answer : D. The number of furrow openers x distance between two furrow
Description : A long jow mould board with a gradual twist (spiral) that completely inverts the furrow slice with a minimum of break up thus covering vegetative matter thoroughly is called a. Sod bottom b. Stubble bottom c. General bottom d. Slat bottom
Last Answer : a. Sod bottom
Description : subsoilers are operated at maximum depth of: A.30-40cm B.45-75cm C.75-90cm D.10-20cm
Last Answer : B.45-75cm
Description : Depth of working of a tillage implement is controlled by a) Furrow Wheel b) Gauge Wheel c) Cage Wheel d) Star Wheel
Last Answer : d) Star Wheel
Description : The type of restrained three point linkage system in which the depth of implement is automatically adjusted to maintain a pre selected constant draft is called : E. Automatic draft control system F. Precision control system G. Depth control system H. None of the above
Last Answer : E. Automatic draft control system
Description : pecific energy requirement of rotary tillers can be reduce by a) Increasing the bite length b) Decreasing depth to diameter ratio c) Both (a) and (b) d) Excessive reduction in total power requirement
Last Answer : c) Both (a) and (b)
Description : In comparison to jump clutchs, advantages of the friction safety clutches is/are a) More consistent break away torque b) No damageing peak during slippage c) Protecting a drive from high freuency peak torque (2-3 time normal values) d) All of the above
Description : An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above
Last Answer : d) None of the above
Description : Gears are used for: a)changing the speed rotation b)changing direction of rotation c)changing direction of shafting d)all of the above
Last Answer : d)all of the above