Description : In an offset disc harrow the angle between two gang is a) less than 90 degree b) 90 degree c) greater than 90 degree d) 180degree
Last Answer : a) less than 90 degre
Description : harrow consist of two gangs placed end to end. A) Single action disc harrow B) Double action disc harrow C) Triple action disc harrow D) None above
Last Answer : Single action disc harrow
Description : Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front
Last Answer : c) concave, convex
Description : The two primery tillage equipment a. MB plough and disc harrow b. Disc plough and disc harrow c. Disc harrow and cultivetor d. MB plough and subsoiler
Last Answer : d. MB plough and subsoiler
Description : Dead furrow is made by: a. One way MB plough b. Two way MB plough c. Ridger d. Disc harrow
Last Answer : a. One way MB plough
Description : .Laying out of field in lands is essential when working with a. Two way plough b. One way plough c. Disc harrow d. Cultivator
Last Answer : b. One way plough
Description : The implement which can work in offset position a)offset disc harrow b) mower c) both (a) and (b) d) none of the above
Last Answer : c) both (a) and (b)
Description : Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front
Last Answer : a) Concave
Description : The depth of penetration of a disc harrow is increased by: a) Tilt angle b) Gang angle c) Disc angle d) All of above
Last Answer : b) Gang angle
Description : A coulter attachment is used with: a. Disc harrow b. Seed drill c. MB plough d. Sub soiler
Last Answer : c. MB ploug
Description : .Land shipping become necessary often the following implments is used: a. MB plough b. Disc harrow c. Cultivator d. All of these
Last Answer : a. MB plough
Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc Harrow c) Cultivator d) All of the above
Last Answer : a) M.B. Plough
Description : Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front
Description : Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true
Last Answer : d) Both (b) and (c) are true
Description : In single action harrow two gangs placed end to end, which through the soil in directions. b. Same c. Diagonal d. None of the above
Last Answer : Ans - a. Opposite
Description : Tandem disc Harrow is a disc Harrow comprising of four gangs in which each gang can be angle in… direction. a. Angular c. Parallel b. Opposite. d. Perpendicular
Last Answer : Opposite
Description : At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above
Last Answer : a) Greater contact area between furrow wall and the convex side of the disc
Description : Identify the following figure- a. Offset disc harrow. c. Single action disc harrow b. Double action disc harrow d. Tandem disc harrow
Description : Types of double action disc harrow A) Tandem disc harrow. C ) None B) Off-set disc harrow. D) Both A and B
Last Answer : Both A and B
Description : Spiral gear are used for transmitting power between two shaft Inclined at a. Right angle to each other and axes can intersect b. Right angle to each other and axes cannot intersect c. At angle slightly lesser or greater than 90 of axles can meet d. None of the above
Last Answer : c. At angle slightly lesser or greater than 90 of axles can meet
Description : 0ff-set disc harrows are best suitable to work for a) primary implement b) breaking clods c) orchard cultivation d) surface finishing
Last Answer : c) orchard cultivation
Description : For maximum moisture conservation ploughing is done with A. mb plough b. cultivator c. chisel plough d. dice harrow
Last Answer : c. chisel plough
Description : The rotary and oscillating tool which does not turn the soil upside down is a) Power tiller b) Rotravator c) Power harrow d) Treader and rotary tiller
Last Answer : c) Power harrow
Description : Rotavator working in reverse direction for compacting soil and giving good touch to inter culturing is called a) Rotary tiller b) Power tiller c) Power harrow d) Treader
Last Answer : d) Treader
Description : One of the main advantages of disc brakes over drum brakes is that the disc brake : U. Can stop a vehicle in a shorter distance V. Is more heat resistant W. Weighs less than drum brakes X. Requires less pedal force to stop the vehicle
Last Answer : . Requires less pedal force to stop the vehicle
Description : The gang angle of disc harrow is adjusted in the range of: a) 0-30 c) 30-60 b) 60-90 d) Above 90
Last Answer : B
Description : A relative short and broad mould board is curved rather abruptly near the top resulting in a greater degree of pulverization is called a. Sod bottom b. Stubble bottom b. General bottom d. Slat bottom
Last Answer : b. General bottom
Description : In a horizontal plate type planter maximum obtainable value of cell fill is : A.Greater then 100% B.Less than 100% C.200% D.None of the above
Last Answer : A.Greater then 100%
Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails
Last Answer : c) Spike tooth and hammer mill
Description : 1Heavy draft of a disc plough is due to: A. Blunt disc B. Furrows too wide C. Loose bearings D. All are currect
Last Answer : D. All are currect
Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc plough c) Cultivator d) All of the above
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill
Last Answer : a) Raspbar type cylinder
Description : In standard disc plow the tilk angel varies between: A.30-40 ° B.40-45° C.20-25° D.2-3°
Last Answer : C.20-25°
Description : In a disc plough with the increase in the disk angle, the transverse component of reaction will a)Increase b) Decrease c) Unaffected d) None of the above
Last Answer : a)Increase
Description : Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle
Last Answer : a)Increasing disc angle
Description : Disc angle adjustment influences: a. Depth of cut b. width of cut c. Soil break up d. Direction of travel
Last Answer : b. width of cut
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill
Description : Heavy draft of a disc plough is due to: a) Blunt disc b) Furrows too wide c) Loose bearings d) All of the above
Last Answer : d) All of the above
Description : The type of bearing generally used to support the discs on a standard disc plough is: A. Ball bearing. B. Tapered roller bearing. C. Plain roller bearing. D. Bush bearing.
Last Answer : B. Tapered roller bearing.
Description : Disc type furrow openers are especially suited to A. Stoney and root infested soils B. Poorly prepared bed in trashy soil C. Hard and sticky soil with considerable amount of debris and mulch D. All of the above
Last Answer : C. Hard and sticky soil with considerable amount of debris and mulch
Description : Penetration of disc plough can be improved by a) Increase disc angle b) Decreasing tilt angle c) Both (a) and (b) d) None of the above
Last Answer : b) Decreasing tilt angle
Description : is a harrow which perform harrow operation by means of set or a number of sets of rotating slat each set being mounted on common shaft. a. Spike tooth harrow c. Triangular harrow b. Acme harrow. d. Disc harrow
Last Answer : Disc harrow
Description : Notched disc blades on disc harrows are provided to a) Enhance penetration b) Improve balancing of gangs c) Save on steel d) Reduce draft
Last Answer : ans a
Description : Turbo chargers or super chargers increases engine power by A. 10-20% C. 50-60% B. 20-30% D. 90-100%
Last Answer : A. 10-20%
Description : Flooding nozzle have spray angle a) 100-150 b) 90-100 c) 60-95 d) 30-45
Last Answer : a) 100-150
Description : the time taken to plough one acre farm with 35 hp tractor is : A)60 minutes b)75 minutes C)90 minutes d)120 minutes
Last Answer : b)75 minutes
Description : The sound level of an agricultural tractor should not exceed : I. 110 dB J. 100 dB K. 90 dB L. 80 dB
Last Answer : K. 90 dB
Description : Juice extraction capacity of vertical three roller type bullock down sugercane crusher E. 50-70% F. 70-90% G. 90-100% H. 30-50%
Last Answer : E. 50-70%
Description : 40 optimum working temperature for diesel engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c
Last Answer : ∙ 88-90°c
Description : ptimum working temperature for petrol engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c
Last Answer : ∙ 71-82°c