raft increases with increase in forward speed for most of the implement, mainly due to a) More rapid acceleration of any soil particles that is moved appreciably b) More working width c) Increased working depth d) Draft decreases with increase in speed of implement

raft increases with increase in forward speed for most of the implement, mainly due to  a) More rapid acceleration of any soil particles that is moved appreciably  b) More working width  
c) Increased working depth  
d) Draft decreases with increase in speed of implement
by

1 Answer

Answer :

a) More rapid acceleration of any soil particles that is moved appreciably
by

Related questions

Soil acceleration increases draft because of a) Increased normal load on soil working surface b) Increased frictional resistance c) Kinetic energy imparted to the soil d) All of the above

Description : Soil acceleration increases draft because of a) Increased normal load on soil working surface b) Increased frictional resistance c) Kinetic energy imparted to the soil d) All of the above

Last Answer : d) All of the above

The type of restrained three point linkage system in which the depth of implement is automatically adjusted to maintain a pre selected constant draft is called : E. Automatic draft control system F. Precision control system G. Depth control system H. None of the above

Description : The type of restrained three point linkage system in which the depth of implement is automatically adjusted to maintain a pre selected constant draft is called : E. Automatic draft control system F. Precision control system G. Depth control system H. None of the above

Last Answer : E. Automatic draft control system

Under a given set of operating conditions, the designer and operator has some control of a)Useful soil resistance b) Parasitic Force c)Draft of implement d) Pull of implement

Description : Under a given set of operating conditions, the designer and operator has some control of a)Useful soil resistance b) Parasitic Force c)Draft of implement d) Pull of implement

Last Answer : b) Parasitic Force

Force ( including rolling resistance friction ) that acts upon the stabilising surfaces such landslide and sole of bottom are called a) Useful soil resistance b) Parasitic force d) Draft of implement. d) Pull of implement

Description : Force ( including rolling resistance friction ) that acts upon the stabilising surfaces such landslide and sole of bottom are called a) Useful soil resistance b) Parasitic force d) Draft of implement. d) Pull of implement

Last Answer : b) Parasitic force

Forces which a tool must overcome in cutting, breaking and moving the soil is called a) Useful soil resistance b) Parasitic force c) Draft of implement d) Pull of implement

Description : Forces which a tool must overcome in cutting, breaking and moving the soil is called a) Useful soil resistance b) Parasitic force c) Draft of implement d) Pull of implement

Last Answer : a) Useful soil resistance

Depth of working of a tillage implement is controlled by a) Furrow Wheel b) Gauge Wheel c) Cage Wheel d) Star Wheel

Description : Depth of working of a tillage implement is controlled by a) Furrow Wheel b) Gauge Wheel c) Cage Wheel d) Star Wheel

Last Answer : d) Star Wheel

Total force exerted upon the implement by a power unit called a)pull. B) draft C)side draft. D)unit draft

Description : Total force exerted upon the implement by a power unit called a)pull. B) draft C)side draft. D)unit draft

Last Answer : a)pull

Durability of the fertilizer increases with a) Increase in the kinetic angle of repose b) Decrease in the kinetic angle of repose c) Decrease in the speed of the forward travel d) None of the above

Description : Durability of the fertilizer increases with a) Increase in the kinetic angle of repose b) Decrease in the kinetic angle of repose c) Decrease in the speed of the forward travel d) None of the above

Last Answer : b) Decrease in the kinetic angle of repose

Disc angle adjustment influences: a. Depth of cut b. width of cut c. Soil break up d. Direction of travel

Description : Disc angle adjustment influences: a. Depth of cut b. width of cut c. Soil break up d. Direction of travel

Last Answer : b. width of cut

At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above

Description : At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above

Last Answer : a) Greater contact area between furrow wall and the convex side of the disc

Rotary tiller are wide adopted in rice cultivation due to a) Excessive pulverization b) Suitability for pudding paddy field c) Reduced draft requirement d) Complete inversion of soil

Description : Rotary tiller are wide adopted in rice cultivation due to a) Excessive pulverization b) Suitability for pudding paddy field c) Reduced draft requirement d) Complete inversion of soil

Last Answer : b) Suitability for pudding paddy field

Size of MB plow is determined by (a) depth of cut (b) width of cut (c) number of accessories (d) none of the above

Description : Size of MB plow is determined by (a) depth of cut (b) width of cut (c) number of accessories (d) none of the above

Last Answer : (b) width of cut

Vetical suction of plough influences: a. Pulverization b. Depth of cut c. Width of cut d. Direction of cut

Description : Vetical suction of plough influences: a. Pulverization b. Depth of cut c. Width of cut d. Direction of cut

Last Answer : b. Depth of cut

.total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Description : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Last Answer : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

A Tillage implement moving at a constant velocity is subjected to a) Force of gravity b) Soil force (resistance) c) Pull of mower d) All of the above

Description : A Tillage implement moving at a constant velocity is subjected to a) Force of gravity b) Soil force (resistance) c) Pull of mower d) All of the above

Last Answer : d) All of the above

.Increase the grain/non grain ratio on the shoe tends to the shoe losses (a) Decreases (b) Increases (c) Decrease or increase (d) Equal

Description : .Increase the grain/non grain ratio on the shoe tends to the shoe losses (a) Decreases (b) Increases (c) Decrease or increase (d) Equal

Last Answer : (d) Equal

Increase amount of non-grain material on the straw walker _______ the walker losses a) Decreases b) Increases c) Unaffected d) Equal

Description : Increase amount of non-grain material on the straw walker _______ the walker losses a) Decreases b) Increases c) Unaffected d) Equal

Last Answer : b) Increase

A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above

Description : A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above

Last Answer : D. All of the above

Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle

Description : Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle

Last Answer : a)Increasing disc angle

1Heavy draft of a disc plough is due to: A. Blunt disc B. Furrows too wide C. Loose bearings D. All are currect

Description : 1Heavy draft of a disc plough is due to: A. Blunt disc B. Furrows too wide C. Loose bearings D. All are currect

Last Answer : D. All are currect

Heavy draft of a disc plough is due to: a) Blunt disc b) Furrows too wide c) Loose bearings d) All of the above

Description : Heavy draft of a disc plough is due to: a) Blunt disc b) Furrows too wide c) Loose bearings d) All of the above

Last Answer : d) All of the above

The depth of penetration of a disc harrow is increased by: a) Tilt angle b) Gang angle c) Disc angle d) All of above

Description : The depth of penetration of a disc harrow is increased by: a) Tilt angle b) Gang angle c) Disc angle d) All of above

Last Answer : b) Gang angle

Application rate of sprayer is affected by a. forward of speed b. number of nozzle c. rate of discharge d. all of the above

Description : Application rate of sprayer is affected by a. forward of speed b. number of nozzle c. rate of discharge d. all of the above

Last Answer : d. all of the above

For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Description : For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Last Answer : D)all of these

The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance between the speed pick up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Description : The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance ... up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index

Description : The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index

Last Answer : (c)reel speed index

The implement which can work in offset position a)offset disc harrow b) mower c) both (a) and (b) d) none of the above

Description : The implement which can work in offset position a)offset disc harrow b) mower c) both (a) and (b) d) none of the above

Last Answer : c) both (a) and (b)

Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc plough c) Cultivator d) All of the above

Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc plough c) Cultivator d) All of the above

Last Answer : a) M.B. Plough

0ff-set disc harrows are best suitable to work for a) primary implement b) breaking clods c) orchard cultivation d) surface finishing

Description : 0ff-set disc harrows are best suitable to work for a) primary implement b) breaking clods c) orchard cultivation d) surface finishing

Last Answer : c) orchard cultivation

Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc Harrow c) Cultivator d) All of the above

Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc Harrow c) Cultivator d) All of the above

Last Answer : a) M.B. Plough

The virtual hitch point of a directional implement is located at: a) Near the front axle b) 40 mm towards the rear axle c) At the power take off shaft d) Between two lower links

Description : The virtual hitch point of a directional implement is located at: a) Near the front axle b) 40 mm towards the rear axle c) At the power take off shaft d) Between two lower links

Last Answer : d) Between two lower links

Swinging drawbar is advantageous because it help A. Taking short turn with machine wider than the tractor B. Reduces side draft C. Leaves only small area uncovered at corner of the fied D. All the above

Description : Swinging drawbar is advantageous because it help A. Taking short turn with machine wider than the tractor B. Reduces side draft C. Leaves only small area uncovered at corner of the fied D. All the above

Last Answer : A. Taking short turn with machine wider than the tractor

Horizontal component of pull perpendicular to the line of motion is called: A.Draft B.Side draft C.Transerve component D. Pull

Description : Horizontal component of pull perpendicular to the line of motion is called: A.Draft B.Side draft C.Transerve component D. Pull

Last Answer : B.Side draft

A power tiller is most suited for : A. Draft operation with rigid tools B. Rotary cultivation C. Stationary operation D. Transport work

Description : A power tiller is most suited for : A. Draft operation with rigid tools B. Rotary cultivation C. Stationary operation D. Transport work

Last Answer : B. Rotary cultivation

Rotary tillers are characterized by a) Lower and negative draft b) High power requirement c) Excessive pulverization d) All the above

Description : Rotary tillers are characterized by a) Lower and negative draft b) High power requirement c) Excessive pulverization d) All the above

Last Answer : d) All the above

Differential lock offers advantage of A. Better drawbar pull when drive wheel are under different conditions B. Easier to plant in straight rows C. Reduces stearing effort and side draft when operating with certain implements D. All of the above

Description : Differential lock offers advantage of A. Better drawbar pull when drive wheel are under different conditions B. Easier to plant in straight rows C. Reduces stearing effort and side draft when operating with certain implements D. All of the above

Last Answer : D. All of the above

A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced

Description : A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced

Last Answer : a. Seed is increase

In forward bias, the width of potential barrier __________ (a) Increases (b) decreases (c) remains same (d) no effect

Description : In forward bias, the width of potential barrier __________ (a) Increases (b) decreases (c) remains same (d) no effect

Last Answer : (b) decreases

Increase in grain/non grain ratio on the straw Walker losses (a) Decrease (b) Increases (c) Unltered (d) None of the above

Description : Increase in grain/non grain ratio on the straw Walker losses (a) Decrease (b) Increases (c) Unltered (d) None of the above

Last Answer : (b) Increases

In a deposit of normally consolidated clay (A) Effective stress increases with depth but water content of soil and undrained strength decrease with depth (B) Effective stress and water content increase with depth but undrained strength decreases with depth C) Effective stress and undrained strength increase with depth but water content decreases with depth (D) Effective stress, water content and undrained strength decrease with depth

Description : In a deposit of normally consolidated clay (A) Effective stress increases with depth but water content of soil and undrained strength decrease with depth (B) Effective stress and water ... decreases with depth (D) Effective stress, water content and undrained strength decrease with depth

Last Answer : C) Effective stress and undrained strength increase with depth but water content decreases with depth

For providing a raft foundation, the following activities are involved 1. Ramming the foundation bed 2. Excavation of the soil upto required depth 3. Laying the reinforcement over the foundation bed 4. Curing the cement concrete placed over reinforcement 5. Pouring the cement concrete over the reinforcement The correct sequence is (A) 1, 2, 3, 4, 5 (B) 5, 4, 3, 2, 1 (C) 2, 1, 3, 5, 4 (D) 3, 2, 5, 1,

Description : For providing a raft foundation, the following activities are involved 1. Ramming the foundation bed 2. Excavation of the soil upto required depth 3. Laying the reinforcement over the foundation bed 4. Curing the cement concrete placed over ... 2, 1 (C) 2, 1, 3, 5, 4 (D) 3, 2, 5, 1, 4

Last Answer : Answer: Option C

What is the principle of a life Jacket'? (1) It provides oxygen to a drowning person (2) It increases the volume of the person to keep him afloat (3) It decreases the volume of the person to keep him afloat (4) The person can sit on it like a raft

Description : What is the principle of a life Jacket'? (1) It provides oxygen to a drowning person (2) It increases the volume of the person to keep him afloat (3) It decreases the volume of the person to keep him afloat (4) The person can sit on it like a raft

Last Answer : (2) It increases the volume of the person to keep him afloat Explanation: The upward-pushing force that keeps things afloat is called buoyancy. For an object to float it must be able to equal ... a person, it acts to significantly increase their volume for only a very small increase in their mass.

What is the principle of a ‘Life Jacket’? (1) It provides oxygen to a drowning person (2) It increases the volume of the person to keep him afloat (3) It decreases the volume of the person to keep him afloat (4) The person can sit on it like a raft

Description : What is the principle of a ‘Life Jacket’? (1) It provides oxygen to a drowning person (2) It increases the volume of the person to keep him afloat (3) It decreases the volume of the person to keep him afloat (4) The person can sit on it like a raft

Last Answer : It increases the volume of the person to keep him afloat

Formula for adding weight (ballast) on tractor tyres working in loose wet soil for good traction a)(km/hr × kg/PTO kw)=540 b)( km/hr × kg/PTO kw)=670 c)( km/hr × kg/PTO HP)=540 d)( km/hr × kg/PTO HP)=670

Description : Formula for adding weight (ballast) on tractor tyres working in loose wet soil for good traction a)(km/hr × kg/PTO kw)=540 b)( km/hr × kg/PTO kw)=670 c)( km/hr × kg/PTO HP)=540 d)( km/hr × kg/PTO HP)=670

Last Answer : a)(km/hr × kg/PTO kw)=540

shaped blades are best suited for i. Minimum tillage of trashy land at shallow depths j. Dried hard soils k. Cutting and pulverisation in wet sticky clay soil l. Working under normal field conditions

Description : shaped blades are best suited for i. Minimum tillage of trashy land at shallow depths j. Dried hard soils k. Cutting and pulverisation in wet sticky clay soil l. Working under normal field conditions

Last Answer : i. Minimum tillage of trashy land at shallow depths

Hook type blades best suited for e. Minimum tillage of trashy land at shallow depths f. Dried hard soils g. Cutting and pulverisation especially in wet sticky clay soil h. Working under normal field conditions

Description : Hook type blades best suited for e. Minimum tillage of trashy land at shallow depths f. Dried hard soils g. Cutting and pulverisation especially in wet sticky clay soil h. Working under normal field conditions

Last Answer : f. Dried hard soils

owest specific energy requirement for the operation of rotavator is about _______ times as great as a mould board plough working in the same soil. a) Equal b) Twice c) Three d) Four

Description : owest specific energy requirement for the operation of rotavator is about _______ times as great as a mould board plough working in the same soil. a) Equal b) Twice c) Three d) Four

Last Answer : c) Three

Rotavator working in reverse direction for compacting soil and giving good touch to inter culturing is called a) Rotary tiller b) Power tiller c) Power harrow d) Treader

Description : Rotavator working in reverse direction for compacting soil and giving good touch to inter culturing is called a) Rotary tiller b) Power tiller c) Power harrow d) Treader

Last Answer : d) Treader

_______ designates the shape of gross peripheral and cross-sectional boundaries of the soil working tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape

Description : _______ designates the shape of gross peripheral and cross-sectional boundaries of the soil working tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape

Last Answer : c) Edge shape

267 .Double knives movers offers advantage over conventional mower are a)Double knife are dynamically balanced b) They can be operated at higher forward speeds then conventional mower c)They produce more uniform stubble height d)All of the above

Description : 267 .Double knives movers offers advantage over conventional mower are a)Double knife are dynamically balanced b) They can be operated at higher forward speeds then conventional mower c)They produce more uniform stubble height d)All of the above

Last Answer : d)All of the above