Description : Which one of the below is a multipurpose tool a) Indigenous plough b) Cultivator c) Multipurpose tool bar carrier d) M.B plough
Last Answer : c) Multipurpose tool bar carrier
Description : 346- Side deflection of stalk can be minimized by.... (a) Having a short cutting stroke (b) Having an arrangement to obtain two cuts per stroke (c) Both (a) & (b) (d) None of the above
Last Answer : (c) Both (a) & (b)
Description : 1Heavy draft of a disc plough is due to: A. Blunt disc B. Furrows too wide C. Loose bearings D. All are currect
Last Answer : D. All are currect
Description : .The land side of a mould board plough is made of: A. Malleable iron B. Forged steel C. C45 steel D. Soft Centre steel
Last Answer : D. Soft Centre steel
Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc plough c) Cultivator d) All of the above
Last Answer : a) M.B. Plough
Description : .Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely
Last Answer : c) No affect
Description : In a disc plough with the increase in the disk angle, the transverse component of reaction will a)Increase b) Decrease c) Unaffected d) None of the above
Last Answer : a)Increase
Description : For maximum moisture conservation ploughing is done with A. mb plough b. cultivator c. chisel plough d. dice harrow
Last Answer : c. chisel plough
Description : Subsoiler plough is best suited for a. breaking hard pan b. deep ploughing c. making ditches d. inter cultivation
Last Answer : a. breaking hard pan
Description : The two primery tillage equipment a. MB plough and disc harrow b. Disc plough and disc harrow c. Disc harrow and cultivetor d. MB plough and subsoiler
Last Answer : d. MB plough and subsoiler
Description : Dead furrow is made by: a. One way MB plough b. Two way MB plough c. Ridger d. Disc harrow
Last Answer : a. One way MB plough
Description : A coulter attachment is used with: a. Disc harrow b. Seed drill c. MB plough d. Sub soiler
Last Answer : c. MB ploug
Description : Vetical suction of plough influences: a. Pulverization b. Depth of cut c. Width of cut d. Direction of cut
Last Answer : b. Depth of cut
Description : .Land shipping become necessary often the following implments is used: a. MB plough b. Disc harrow c. Cultivator d. All of these
Last Answer : a. MB plough
Description : the time taken to plough one acre farm with 35 hp tractor is : A)60 minutes b)75 minutes C)90 minutes d)120 minutes
Last Answer : b)75 minutes
Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc Harrow c) Cultivator d) All of the above
Description : Heavy draft of a disc plough is due to: a) Blunt disc b) Furrows too wide c) Loose bearings d) All of the above
Last Answer : d) All of the above
Description : The landside of a mould board plough is made of: a) Malleable iron b) Forged steel c) C45 steel d) Soft centre steel
Last Answer : d) Soft centre steel
Description : A power tiller is relatively more suitable for : A. Puddling of low land paddy fields with a rotary tiller B. Primary tillage of upland paddy fields with a rotary tillers C. Primary tillage with a mould board plough D. Farm transportation work
Last Answer : A. Puddling of low land paddy fields with a rotary tiller
Description : The type of bearing generally used to support the discs on a standard disc plough is: A. Ball bearing. B. Tapered roller bearing. C. Plain roller bearing. D. Bush bearing.
Last Answer : B. Tapered roller bearing.
Description : owest specific energy requirement for the operation of rotavator is about _______ times as great as a mould board plough working in the same soil. a) Equal b) Twice c) Three d) Four
Last Answer : c) Three
Description : …………………………... moves the trash and roots from ahead of shin towords the main furrow so as 10 ensure complete coverage by the plough bottom a. Coulter b. Jointer c. Mould board d. Shin
Last Answer : b. Jointer
Description : A mould board plough bottom acts as a a. Single sided wedge b. Double sided wedge c. Three sided wedge d. All of the above
Last Answer : c. Three sided wedg
Description : .Laying out of field in lands is essential when working with a. Two way plough b. One way plough c. Disc harrow d. Cultivator
Last Answer : b. One way plough
Description : Penetration of disc plough can be improved by a) Increase disc angle b) Decreasing tilt angle c) Both (a) and (b) d) None of the above
Last Answer : b) Decreasing tilt angle
Description : At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above
Last Answer : a) Greater contact area between furrow wall and the convex side of the disc
Description : What is the field capacity of an Indigenous Plough? [a] 0.4 ha per day of 8 hours [b] 0.6 ha per day of 8 hours [c] 0.8 ha per day of 8 hours [d] 0.2 ha per day of 8 hours
Last Answer : [a] 0.4 ha per day of 8 hours
Description : Jointer and coulter are the parts of :- A. Disc plough C. Indigenous plough B. Harrow plough D. MB plough
Last Answer : MB plough
Description : _______ designates the shape of gross peripheral and cross-sectional boundaries of the soil working tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape
Last Answer : c) Edge shape
Description : Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above
Last Answer : (d) All of the above
Description : A battery of emf 2 V and internal resistance `0.5 Omega` is connected across a resistance of `9.5 Omega`. How many electrons pass through a cross-sect
Last Answer : A battery of emf 2 V and internal resistance `0.5 Omega` is connected across a resistance of `9. ... a cross-section of the resistance in 1 second ?
Description : verticalsuctioninmouldboardploughis______whereashorizontalsuctionis______
Last Answer : .0.3to0.5cm,0.5cm
Description : Byincreasingdiskangle,depthpenetration_____beoverwithofcut_______
Last Answer : .decreases,increases
Description : A paddy transplanter uses either root wash type seedlings or __________ seedlings.
Last Answer : soil bearing
Description : The unit of filter medium resistance is________
Last Answer : L^-1
Description : The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.
Last Answer : 35
Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.
Last Answer : 1200 to 1500
Description : In sprayers , operating pressures below ___________Kpa are undesirable for hydraulic nozzles other than flooding type
Last Answer : 140
Description : Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm
Last Answer : a) 300-400rpm
Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm
Last Answer : d) 1100-1200rpm
Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm
Last Answer : c) 600-800rpm
Description : Air output of a duster is given by formula a) Q= 60×A×V b)Q= 60×A×(2GH/Y) c) Q= 240×A×h d) all of the above
Last Answer : d) all of the above
Description : Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives
Last Answer : a) gears
Description : Transplanter using soil bearing seedlings are more popular than washed root seedling transplanter because of a) less labour requirement b) lesser plant missing percentage c) higher work rates d) all of the above
Description : Superchargers are driven by A. Electric current from the battery B. Exhaust gases from engine C. Direct connection with the engine power D. None of the above
Last Answer : C. Direct connection with the engine power
Description : Turbo chargers are driven by A. Direct connection with engine power B. Exhaust gases from engine C. Electric current from the battery D. None of the above
Last Answer : B. Exhaust gases from engine
Description : Turbo chargers or super chargers increases engine power by A. 10-20% C. 50-60% B. 20-30% D. 90-100%
Last Answer : A. 10-20%
Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above
Last Answer : B. L-head
Description : Utility index is a indication of A. Work machine contact hours B. Wear out life of machine C. Operating cost of machine D. Reliability of machine working
Last Answer : A. Work machine contact hours
Description : Alternators are preferred over dynamo because A. Alternators can produce a strong current of 30-40 amperes. B. Alternators don’t required cutout reiny C. Alternators don’t have commutaters D. All of the above
Last Answer : D. All of the above