Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc plough c) Cultivator d) All of the above
Last Answer : a) M.B. Plough
Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc Harrow c) Cultivator d) All of the above
Description : For maximum moisture conservation ploughing is done with A. mb plough b. cultivator c. chisel plough d. dice harrow
Last Answer : c. chisel plough
Description : .Land shipping become necessary often the following implments is used: a. MB plough b. Disc harrow c. Cultivator d. All of these
Last Answer : a. MB plough
Description : .Laying out of field in lands is essential when working with a. Two way plough b. One way plough c. Disc harrow d. Cultivator
Last Answer : b. One way plough
Description : An indigenous plough cuts a _________furrow cross sect
Last Answer : Trapizoidal
Description : Which of the following is not a tractor drawn tillage tool? 1. Cultivator 2. Augar plough 3. Harrow 4. Plank
Last Answer : ans 4
Description : is not a tractor drawn tillage tool A. Cultivator B. Augar plough C. Narrow D. Plank
Last Answer : Plank
Description : is not a tractor drawn tillage tool: a) Cultivator c) Augar plough b) Harrow d) Plank
Description : Which plough will be used for maximum moisture conservation ? a. M B Plugh b. Cultivator c. Chisel plough d. Disc harrow
Last Answer : c. Chisel plough
Description : 1Heavy draft of a disc plough is due to: A. Blunt disc B. Furrows too wide C. Loose bearings D. All are currect
Last Answer : D. All are currect
Description : .The land side of a mould board plough is made of: A. Malleable iron B. Forged steel C. C45 steel D. Soft Centre steel
Last Answer : D. Soft Centre steel
Description : .Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely
Last Answer : c) No affect
Description : In a disc plough with the increase in the disk angle, the transverse component of reaction will a)Increase b) Decrease c) Unaffected d) None of the above
Last Answer : a)Increase
Description : Subsoiler plough is best suited for a. breaking hard pan b. deep ploughing c. making ditches d. inter cultivation
Last Answer : a. breaking hard pan
Description : The two primery tillage equipment a. MB plough and disc harrow b. Disc plough and disc harrow c. Disc harrow and cultivetor d. MB plough and subsoiler
Last Answer : d. MB plough and subsoiler
Description : Dead furrow is made by: a. One way MB plough b. Two way MB plough c. Ridger d. Disc harrow
Last Answer : a. One way MB plough
Description : A coulter attachment is used with: a. Disc harrow b. Seed drill c. MB plough d. Sub soiler
Last Answer : c. MB ploug
Description : Vetical suction of plough influences: a. Pulverization b. Depth of cut c. Width of cut d. Direction of cut
Last Answer : b. Depth of cut
Description : the time taken to plough one acre farm with 35 hp tractor is : A)60 minutes b)75 minutes C)90 minutes d)120 minutes
Last Answer : b)75 minutes
Description : Heavy draft of a disc plough is due to: a) Blunt disc b) Furrows too wide c) Loose bearings d) All of the above
Last Answer : d) All of the above
Description : The landside of a mould board plough is made of: a) Malleable iron b) Forged steel c) C45 steel d) Soft centre steel
Last Answer : d) Soft centre steel
Description : A power tiller is relatively more suitable for : A. Puddling of low land paddy fields with a rotary tiller B. Primary tillage of upland paddy fields with a rotary tillers C. Primary tillage with a mould board plough D. Farm transportation work
Last Answer : A. Puddling of low land paddy fields with a rotary tiller
Description : The type of bearing generally used to support the discs on a standard disc plough is: A. Ball bearing. B. Tapered roller bearing. C. Plain roller bearing. D. Bush bearing.
Last Answer : B. Tapered roller bearing.
Description : owest specific energy requirement for the operation of rotavator is about _______ times as great as a mould board plough working in the same soil. a) Equal b) Twice c) Three d) Four
Last Answer : c) Three
Description : …………………………... moves the trash and roots from ahead of shin towords the main furrow so as 10 ensure complete coverage by the plough bottom a. Coulter b. Jointer c. Mould board d. Shin
Last Answer : b. Jointer
Description : A mould board plough bottom acts as a a. Single sided wedge b. Double sided wedge c. Three sided wedge d. All of the above
Last Answer : c. Three sided wedg
Description : Penetration of disc plough can be improved by a) Increase disc angle b) Decreasing tilt angle c) Both (a) and (b) d) None of the above
Last Answer : b) Decreasing tilt angle
Description : At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above
Last Answer : a) Greater contact area between furrow wall and the convex side of the disc
Description : o over come the rear ward deflection the load given to outer end of the cutter bar is about..... (a)1.57cm/m (b) 2.0cm/m (b)3.0cm/m (d) 3.5cm/m
Last Answer : b) 2.0cm/m
Description : The two primary tillage equipments are 1. MB and disc harrow 2. Disc plough and disc harrow 3. Disc harrow and cultivator 4. MB and subsoiler
Description : The two primary tillage equipments are A. MB and disc harrow B. Disc plough and disc harrow C. Disc harrow and cultivator. D. MB and. Subscriber
Last Answer : MB and disc harrow
Description : Which of the following is not a tractor drawn primary tillage tool? 1. Disc plough 2. rotavator 3. Country plough 4. Bar harrow
Last Answer : ans 3
Description : Scouring indicates: A. movement of soil on tool surface B. sticking of soil on tool surface C. inversion of soil D. none of the above
Last Answer : A. movement of soil on tool surface
Description : illage tool moving with uniform velocity is subjected to A)force of gravity. B)pull of power source C)soil reaction. D)all of the above
Last Answer : D)all of the above
Description : The rotary and oscillating tool which does not turn the soil upside down is a) Power tiller b) Rotravator c) Power harrow d) Treader and rotary tiller
Last Answer : c) Power harrow
Description : _______ designates the shape of gross peripheral and cross-sectional boundaries of the soil working tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape
Last Answer : c) Edge shape
Description : ________ refer to the surface roughness of the tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape
Last Answer : a) Micro shape
Description : he shape of the gross surface of the tillage tool is designated as a) Micro shape c) Edge shape b) Macro shape d) Gross shape
Last Answer : b) Macro shape
Description : The amount of energy required to produce a given degree of pulverisation depends primarily on a) Soil strength b) Energy utilisation efficiency of tool c) Both (a) and (b) d) None of the above
Last Answer : c) Both (a) and (b)
Description : Scouring will occur as long as a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face b) Frictional resistance at soil tool interface is more than ... c) Soil-metal friction is more than angle of soil shearing resistance d) None of the above
Last Answer : a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face
Description : _________means movement of soils across a tool surface without sticking first to avoid soil build ups a) Pulverisation b) Inversion c) Scouring d) Turning
Last Answer : c) Scouring
Description : Forces which a tool must overcome in cutting, breaking and moving the soil is called a) Useful soil resistance b) Parasitic force c) Draft of implement d) Pull of implement
Last Answer : a) Useful soil resistance
Description : What is the field capacity of an Indigenous Plough? [a] 0.4 ha per day of 8 hours [b] 0.6 ha per day of 8 hours [c] 0.8 ha per day of 8 hours [d] 0.2 ha per day of 8 hours
Last Answer : [a] 0.4 ha per day of 8 hours
Description : Jointer and coulter are the parts of :- A. Disc plough C. Indigenous plough B. Harrow plough D. MB plough
Last Answer : MB plough
Description : The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links
Last Answer : D. Between the two lower Links
Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails
Last Answer : c) Spike tooth and hammer mill
Description : The cutter bar of a tractor operated mower ordinarily makes: A. 800-1200 strokes/min B. 1600-2000 strokes/min C. 2400-2800 strokes/min D. 3200-3600 strokes/min
Last Answer : A. 800-1200 strokes/min
Description : Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder
Last Answer : (b) Spike tooth cylinder