The unit of filter medium resistance is________

The unit of filter medium resistance is________
by

1 Answer

Answer :

L^-1
by

Related questions

Medium Carbon steel was carbon content about (A) 0.25 % (B) 0.25 – 0.50 % (C) 0.50 – 1.5 % (D) 2.5 – 4.5 %

Description : Medium Carbon steel was carbon content about (A) 0.25 % (B) 0.25 – 0.50 % (C) 0.50 – 1.5 % (D) 2.5 – 4.5 %

Last Answer : (B) 0.25 – 0.50 %

Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Description : Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Last Answer : a) Fluted wheel

peed of a medium speed engine is (a) <350 rpm (b) 350-1000 rpm (c) >1000rpm (d) none of the above

Description : peed of a medium speed engine is (a) 1000rpm (d) none of the above

Last Answer : (b) 350-1000 rpm

The unit of filter medium resistance is(A) cm-1(B) gm/cm-1(C) cm/gm-1(D) gm-1

Description : The unit of filter medium resistance is (A) cm-1 (B) gm/cm-1 (C) cm/gm-1 (D) gm-1

Last Answer : (A) cm-1

Wood is well suited to use as bearing on straw walker cranks in combine due to fact a) Wood corrosion resistance b) Split bearing are needed for practical purpose c) It can take radial as well as thrust loads d) No lubrication is required

Description : Wood is well suited to use as bearing on straw walker cranks in combine due to fact a) Wood corrosion resistance b) Split bearing are needed for practical purpose c) It can take radial as well as thrust loads d) No lubrication is required

Last Answer : b) Split bearing are needed for practical purpose

Soil acceleration increases draft because of a) Increased normal load on soil working surface b) Increased frictional resistance c) Kinetic energy imparted to the soil d) All of the above

Description : Soil acceleration increases draft because of a) Increased normal load on soil working surface b) Increased frictional resistance c) Kinetic energy imparted to the soil d) All of the above

Last Answer : d) All of the above

Scouring will occur as long as a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face b) Frictional resistance at soil tool interface is more than the resistance at parallel soil-soil inter face c) Soil-metal friction is more than angle of soil shearing resistance d) None of the above

Description : Scouring will occur as long as a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face b) Frictional resistance at soil tool interface is more than ... c) Soil-metal friction is more than angle of soil shearing resistance d) None of the above

Last Answer : a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face

Under a given set of operating conditions, the designer and operator has some control of a)Useful soil resistance b) Parasitic Force c)Draft of implement d) Pull of implement

Description : Under a given set of operating conditions, the designer and operator has some control of a)Useful soil resistance b) Parasitic Force c)Draft of implement d) Pull of implement

Last Answer : b) Parasitic Force

Force ( including rolling resistance friction ) that acts upon the stabilising surfaces such landslide and sole of bottom are called a) Useful soil resistance b) Parasitic force d) Draft of implement. d) Pull of implement

Description : Force ( including rolling resistance friction ) that acts upon the stabilising surfaces such landslide and sole of bottom are called a) Useful soil resistance b) Parasitic force d) Draft of implement. d) Pull of implement

Last Answer : b) Parasitic force

Forces which a tool must overcome in cutting, breaking and moving the soil is called a) Useful soil resistance b) Parasitic force c) Draft of implement d) Pull of implement

Description : Forces which a tool must overcome in cutting, breaking and moving the soil is called a) Useful soil resistance b) Parasitic force c) Draft of implement d) Pull of implement

Last Answer : a) Useful soil resistance

A Tillage implement moving at a constant velocity is subjected to a) Force of gravity b) Soil force (resistance) c) Pull of mower d) All of the above

Description : A Tillage implement moving at a constant velocity is subjected to a) Force of gravity b) Soil force (resistance) c) Pull of mower d) All of the above

Last Answer : d) All of the above

Weight per unit of drawbar power is generally ranges between a)50-120kg/kw b)120-150kg/kw c)150-250kg/kw d)250-300kg/kw

Description : Weight per unit of drawbar power is generally ranges between a)50-120kg/kw b)120-150kg/kw c)150-250kg/kw d)250-300kg/kw

Last Answer : a)50-120kg/kw

Total force exerted upon the implement by a power unit called a)pull. B) draft C)side draft. D)unit draft

Description : Total force exerted upon the implement by a power unit called a)pull. B) draft C)side draft. D)unit draft

Last Answer : a)pull

In an epicycle gear reduction unit, the ratio of the number of teeth of the internal gears to the sun gear is: a) 3:1 b) 4:1 c) 2.5:1 d) 4.5:1

Description : In an epicycle gear reduction unit, the ratio of the number of teeth of the internal gears to the sun gear is: a) 3:1 b) 4:1 c) 2.5:1 d) 4.5:1

Last Answer : b) 4:1

The size of a seed rill is expressed by: A. Amount of seed sown per unit time. B. Length x width of the machine. C. Area covered per unit time. D. The number of furrow openers x distance between two furrow

Description : The size of a seed rill is expressed by: A. Amount of seed sown per unit time. B. Length x width of the machine. C. Area covered per unit time. D. The number of furrow openers x distance between two furrow

Last Answer : D. The number of furrow openers x distance between two furrow

Variation in the drop size of seed can be minimised by (a) Using a short, smooth, small diameter tube with the discharge end close to bottom of furrow. (b) Discharging the seed directly from the metering device within a few centimetres of the furrow bottom. (c) Mechanically transferring the seeds from the metering unit in the furrow. (d) All of the above.

Description : Variation in the drop size of seed can be minimised by (a) Using a short, smooth, small diameter tube with the discharge end close to bottom of furrow. (b) Discharging the seed directly from ... (c) Mechanically transferring the seeds from the metering unit in the furrow. (d) All of the above.

Last Answer : d) All of the above.

The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance between the speed pick up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Description : The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance ... up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

345- Excessive stalk deflection particularly when cutting close to ground results in ...... (a) Stubbles of uneven length (b) Increased tedency of stalk to cut by cutting unit..... (c) Less unevenness in cutting (d) Less missing or uncut stalk

Description : 345- Excessive stalk deflection particularly when cutting close to ground results in ...... (a) Stubbles of uneven length (b) Increased tedency of stalk to cut by cutting unit..... (c) Less unevenness in cutting (d) Less missing or uncut stalk

Last Answer : (a) Stubbles of uneven length

Filter medium resistance is important during the __________ of filtration. (A) Early stages (B) Final stages (C) Entire process (D) None of these

Description : Filter medium resistance is important during the __________ of filtration. (A) Early stages (B) Final stages (C) Entire process (D) None of these

Last Answer : (A) Early stages

Filter medium resistance is that offered by the(A) Filter cloth(B) Embedded particles in the septum(C) Filter cloth and the embedded particle collectively(D) None of these

Description : Filter medium resistance is that offered by the (A) Filter cloth (B) Embedded particles in the septum (C) Filter cloth and the embedded particle collectively (D) None of these

Last Answer : (C) Filter cloth and the embedded particle collectively

Filter aids like asbestos, kieselguhr, diatomaceous earth etc. are used to increase the porosity of the final filter cake & reducing the cake resistance during filtration. Filter aid is (A) Added to the feed slurry (B) Pre-coated on the filter medium prior to filtration (C) Separated from the cake by dissolving solids or by burning it off (D) All 'a', 'b' & 'c'

Description : Filter aids like asbestos, kieselguhr, diatomaceous earth etc. are used to increase the porosity of the final filter cake & reducing the cake resistance during filtration. Filter aid is (A) Added to the feed slurry (B) Pre ... the cake by dissolving solids or by burning it off (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

During the washing of cake (A) All the resistances are constant (B) Filter medium resistance increases (C) Filter medium resistance decreases (D) Cake resistance decreases

Description : During the washing of cake (A) All the resistances are constant (B) Filter medium resistance increases (C) Filter medium resistance decreases (D) Cake resistance decreases

Last Answer : (A) All the resistances are constant

The controlling resistance in a rotary drum vacuum filter is the __________ resistance.(A) Piping (B) Cake (C) Filter medium (D) None of these

Description : The controlling resistance in a rotary drum vacuum filter is the __________ resistance. (A) Piping (B) Cake (C) Filter medium (D) None of these

Last Answer : (B) Cake

During filtration operation, the filtrate encounters the resistance of the (A) Filter medium (B) Cake (C) Channel carrying the slurry to the upstream side of the cake and filtrate away from the filter medium (D) All (A), (B) and (C)

Description : During filtration operation, the filtrate encounters the resistance of the (A) Filter medium (B) Cake (C) Channel carrying the slurry to the upstream side of the cake and filtrate away from the filter medium (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Filtrate flow rate in case of a rotary drum vacuum filter (in which Rm < < Rc ) is proportional to __________ and the cycle time (where, μ = filtrate viscosity Rm = filter medium resistance Rc = cake resistance). (A) √μ (B) 1/√μ (C) 1/μ (D) 1/μ

Description : Filtrate flow rate in case of a rotary drum vacuum filter (in which Rm < < Rc ) is proportional to __________ and the cycle time (where, μ = filtrate viscosity Rm = filter medium resistance Rc = cake resistance). (A) √μ (B) 1/√μ (C) 1/μ (D) 1/μ

Last Answer : (B) 1/√μ

verticalsuctioninmouldboardploughis______whereashorizontalsuctionis______

Description : verticalsuctioninmouldboardploughis______whereashorizontalsuctionis______

Last Answer : .0.3to0.5cm,0.5cm

Byincreasingdiskangle,depthpenetration_____beoverwithofcut_______

Description : Byincreasingdiskangle,depthpenetration_____beoverwithofcut_______

Last Answer : .decreases,increases

A paddy transplanter uses either root wash type seedlings or __________ seedlings.

Description : A paddy transplanter uses either root wash type seedlings or __________ seedlings.

Last Answer : soil bearing

An indigenous plough cuts a _________furrow cross sect

Description : An indigenous plough cuts a _________furrow cross sect

Last Answer : Trapizoidal

The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.

Description : The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.

Last Answer : 35

In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Last Answer : 1200 to 1500

In sprayers , operating pressures below ___________Kpa are undesirable for hydraulic nozzles other than flooding type

Description : In sprayers , operating pressures below ___________Kpa are undesirable for hydraulic nozzles other than flooding type

Last Answer : 140

Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : a) 300-400rpm

Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : d) 1100-1200rpm

Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Last Answer : c) 600-800rpm

Air output of a duster is given by formula a) Q= 60×A×V b)Q= 60×A×(2GH/Y) c) Q= 240×A×h d) all of the above

Description : Air output of a duster is given by formula a) Q= 60×A×V b)Q= 60×A×(2GH/Y) c) Q= 240×A×h d) all of the above

Last Answer : d) all of the above

Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives

Description : Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives

Last Answer : a) gears

Transplanter using soil bearing seedlings are more popular than washed root seedling transplanter because of a) less labour requirement b) lesser plant missing percentage c) higher work rates d) all of the above

Description : Transplanter using soil bearing seedlings are more popular than washed root seedling transplanter because of a) less labour requirement b) lesser plant missing percentage c) higher work rates d) all of the above

Last Answer : d) all of the above

Superchargers are driven by A. Electric current from the battery B. Exhaust gases from engine C. Direct connection with the engine power D. None of the above

Description : Superchargers are driven by A. Electric current from the battery B. Exhaust gases from engine C. Direct connection with the engine power D. None of the above

Last Answer : C. Direct connection with the engine power

Turbo chargers are driven by A. Direct connection with engine power B. Exhaust gases from engine C. Electric current from the battery D. None of the above

Description : Turbo chargers are driven by A. Direct connection with engine power B. Exhaust gases from engine C. Electric current from the battery D. None of the above

Last Answer : B. Exhaust gases from engine

Turbo chargers or super chargers increases engine power by A. 10-20% C. 50-60% B. 20-30% D. 90-100%

Description : Turbo chargers or super chargers increases engine power by A. 10-20% C. 50-60% B. 20-30% D. 90-100%

Last Answer : A. 10-20%

.When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Last Answer : B. L-head

Utility index is a indication of A. Work machine contact hours B. Wear out life of machine C. Operating cost of machine D. Reliability of machine working

Description : Utility index is a indication of A. Work machine contact hours B. Wear out life of machine C. Operating cost of machine D. Reliability of machine working

Last Answer : A. Work machine contact hours

Alternators are preferred over dynamo because A. Alternators can produce a strong current of 30-40 amperes. B. Alternators don’t required cutout reiny C. Alternators don’t have commutaters D. All of the above

Description : Alternators are preferred over dynamo because A. Alternators can produce a strong current of 30-40 amperes. B. Alternators don’t required cutout reiny C. Alternators don’t have commutaters D. All of the above

Last Answer : D. All of the above

main function of the current regulator is A. To prevent the reversal flow of current from the battery when dynamo speed is drops. B. To safeguard against flow of high currents to battery when armature develops more current. C. To prevent building up of high voltage in a circuit. D. None of the above

Description : main function of the current regulator is A. To prevent the reversal flow of current from the battery when dynamo speed is drops. B. To safeguard against flow of high currents to battery when armature develops ... . C. To prevent building up of high voltage in a circuit. D. None of the above

Last Answer : B. To safeguard against flow of high currents to battery when armature develops more current.

Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at high speed. C. To permit the generation to deliver current to the battery or to the lightening and ignition circuit. D. None of the above

Description : Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at ... deliver current to the battery or to the lightening and ignition circuit. D. None of the above

Last Answer : A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces.

.Fandem wheels are preferred over dual wheels because a) they tends to reduce load on an area by50% b)they tends to reduce soil contact pressure c)reduces sub soil compact ness pressure d)none of the above

Description : .Fandem wheels are preferred over dual wheels because a) they tends to reduce load on an area by50% b)they tends to reduce soil contact pressure c)reduces sub soil compact ness pressure d)none of the above

Last Answer : a) they tends to reduce load on an area by50%

Dual wheels have disadvantage of a)reducing soil contact pressure and sub soil compact negative pressure b) concentrating load over an area c)reduces load on area by 50% d) none of the above

Description : Dual wheels have disadvantage of a)reducing soil contact pressure and sub soil compact negative pressure b) concentrating load over an area c)reduces load on area by 50% d) none of the above

Last Answer : b) concentrating load over an area

Suggested or recommended difference in mass to power ratio between ballasted and unballasted tractor is of the order a)10kg/PTO KW b)6kg/PTO kw c)20kg/PTO kw d)30kg/PTO kw

Description : Suggested or recommended difference in mass to power ratio between ballasted and unballasted tractor is of the order a)10kg/PTO KW b)6kg/PTO kw c)20kg/PTO kw d)30kg/PTO kw

Last Answer : b)6kg/PTO kw