Description : Penetration of disc plough can be improved by a. Increasing disc angle b. Decreasing tilt angle c. Both a & b d. None of these
Last Answer : b. Decreasing tilt angle
Description : The depth of penetration of a disc harrow is increased by: a) Tilt angle b) Gang angle c) Disc angle d) All of above
Last Answer : b) Gang angle
Description : Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle
Last Answer : a)Increasing disc angle
Description : In a disc plough with the increase in the disk angle, the transverse component of reaction will a)Increase b) Decrease c) Unaffected d) None of the above
Last Answer : a)Increase
Description : At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above
Last Answer : a) Greater contact area between furrow wall and the convex side of the disc
Description : The penetration of a tandem disc harrow can be increased by a) Increasing tilt angle b) Increasing disc angle c) Increasing disc diameter d) All of the above Ans.c
Last Answer : Ans.c
Description : Tilt angle of a disc plough is generally— (A) 10° (B) 15° (C) 20° (D) 45°
Last Answer : (D) 45°
Description : 1Heavy draft of a disc plough is due to: A. Blunt disc B. Furrows too wide C. Loose bearings D. All are currect
Last Answer : D. All are currect
Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc plough c) Cultivator d) All of the above
Last Answer : a) M.B. Plough
Description : The two primery tillage equipment a. MB plough and disc harrow b. Disc plough and disc harrow c. Disc harrow and cultivetor d. MB plough and subsoiler
Last Answer : d. MB plough and subsoiler
Description : Dead furrow is made by: a. One way MB plough b. Two way MB plough c. Ridger d. Disc harrow
Last Answer : a. One way MB plough
Description : A coulter attachment is used with: a. Disc harrow b. Seed drill c. MB plough d. Sub soiler
Last Answer : c. MB ploug
Description : .Land shipping become necessary often the following implments is used: a. MB plough b. Disc harrow c. Cultivator d. All of these
Last Answer : a. MB plough
Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc Harrow c) Cultivator d) All of the above
Description : Heavy draft of a disc plough is due to: a) Blunt disc b) Furrows too wide c) Loose bearings d) All of the above
Last Answer : d) All of the above
Description : The type of bearing generally used to support the discs on a standard disc plough is: A. Ball bearing. B. Tapered roller bearing. C. Plain roller bearing. D. Bush bearing.
Last Answer : B. Tapered roller bearing.
Description : .Laying out of field in lands is essential when working with a. Two way plough b. One way plough c. Disc harrow d. Cultivator
Last Answer : b. One way plough
Description : .Large tilt angle best for a) Hard soil b) Sticky and non-scouring soil c) Dry and cemented soil d None of the above
Last Answer : b) Sticky and non-scouring soil
Description : .Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely
Last Answer : c) No affect
Description : In an offset disc harrow the angle between two gang is a) less than 90 degree b) 90 degree c) greater than 90 degree d) 180degree
Last Answer : a) less than 90 degre
Description : Disc angle adjustment influences: a. Depth of cut b. width of cut c. Soil break up d. Direction of travel
Last Answer : b. width of cut
Description : It Is used for deep tillage and penetration of soil for storage for rain water in crop root zone. b. Disc plough c. Mould board plough d. None of the above
Last Answer : Ans- a. Chisel plough
Description : The tilt angle varies form…° to….. °. For a good plough a. 20°,30°. c) 15°,30° b. 10°,30°. d) 15°,25°
Last Answer : 15°,25°
Description : An indigenous plough cuts a _________furrow cross sect
Last Answer : Trapizoidal
Description : .The land side of a mould board plough is made of: A. Malleable iron B. Forged steel C. C45 steel D. Soft Centre steel
Last Answer : D. Soft Centre steel
Description : Which one of the below is a multipurpose tool a) Indigenous plough b) Cultivator c) Multipurpose tool bar carrier d) M.B plough
Last Answer : c) Multipurpose tool bar carrier
Description : For maximum moisture conservation ploughing is done with A. mb plough b. cultivator c. chisel plough d. dice harrow
Last Answer : c. chisel plough
Description : Subsoiler plough is best suited for a. breaking hard pan b. deep ploughing c. making ditches d. inter cultivation
Last Answer : a. breaking hard pan
Description : Vetical suction of plough influences: a. Pulverization b. Depth of cut c. Width of cut d. Direction of cut
Last Answer : b. Depth of cut
Description : the time taken to plough one acre farm with 35 hp tractor is : A)60 minutes b)75 minutes C)90 minutes d)120 minutes
Last Answer : b)75 minutes
Description : The landside of a mould board plough is made of: a) Malleable iron b) Forged steel c) C45 steel d) Soft centre steel
Last Answer : d) Soft centre steel
Description : A power tiller is relatively more suitable for : A. Puddling of low land paddy fields with a rotary tiller B. Primary tillage of upland paddy fields with a rotary tillers C. Primary tillage with a mould board plough D. Farm transportation work
Last Answer : A. Puddling of low land paddy fields with a rotary tiller
Description : owest specific energy requirement for the operation of rotavator is about _______ times as great as a mould board plough working in the same soil. a) Equal b) Twice c) Three d) Four
Last Answer : c) Three
Description : …………………………... moves the trash and roots from ahead of shin towords the main furrow so as 10 ensure complete coverage by the plough bottom a. Coulter b. Jointer c. Mould board d. Shin
Last Answer : b. Jointer
Description : A mould board plough bottom acts as a a. Single sided wedge b. Double sided wedge c. Three sided wedge d. All of the above
Last Answer : c. Three sided wedg
Description : pecific energy requirement of rotary tillers can be reduce by a) Increasing the bite length b) Decreasing depth to diameter ratio c) Both (a) and (b) d) Excessive reduction in total power requirement
Last Answer : c) Both (a) and (b)
Description : The implement which can work in offset position a)offset disc harrow b) mower c) both (a) and (b) d) none of the above
Last Answer : c) both (a) and (b)
Description : Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true
Last Answer : d) Both (b) and (c) are true
Description : Improved uniformity is obtained if seed tube is inclined rear ward at _________ with vertical. a)5-15° b)15-30° c)30-40° d)40-50
Last Answer : b)15-30°
Description : Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder
Last Answer : a.) Decreasing cylinder peripheral speed.
Description : Function of idler pully are a. to increase the angle of contact of belt on pully b. maintain belt tension as belt stretches c. canter to centre distance remain same d. all the above
Last Answer : d. all the above
Description : swirl plate in the cone nozzle is provided to. a. Impart rotational motion to the liquid passing through it. b. To increase the droplet size. c. To decrease the droplet size. d. To increase the spray angle.
Last Answer : a. Impart rotational motion to the liquid passing through it.
Description : Durability of the fertilizer increases with a) Increase in the kinetic angle of repose b) Decrease in the kinetic angle of repose c) Decrease in the speed of the forward travel d) None of the above
Last Answer : b) Decrease in the kinetic angle of repose
Description : n single action disc harrow the two gangs are at set single a) less than 90 degree b) at 90 degree c) greater than 90 degree d) at 180 degree
Last Answer : c) greater than 90 degree
Description : Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front
Last Answer : a) Concave
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill
Last Answer : a) Raspbar type cylinder
Description : 0ff-set disc harrows are best suitable to work for a) primary implement b) breaking clods c) orchard cultivation d) surface finishing
Last Answer : c) orchard cultivation
Description : In standard disc plow the tilk angel varies between: A.30-40 ° B.40-45° C.20-25° D.2-3°
Last Answer : C.20-25°
Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails
Last Answer : c) Spike tooth and hammer mill
Description : Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front