With a 12 V supply, a silicon diode, and a 370 - ohm resistor in series, what voltage will be dropped across...

With a 12 V supply, a silicon diode, and a 370 - ohm resistor in series, what voltage will be dropped across the diode? a) 0.3V b) 0.7V c) 0.9V d) 1.4V
by

2 Answers

Answer :

With a 12 V supply, a silicon diode, and a 370 - ohm resistor in series, what voltage will be dropped across the diode?

0.7V

by

Answer :

0.7V
by

Related questions

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

For practical purposes, in a simple series circuit, the source voltage will be dropped across one resistor if it has ______________. A. half the resistance of the other resistor B. a resistance equal to the other C. at least ten times the resistance of the other D. a partial short circuit

Description : For practical purposes, in a simple series circuit, the source voltage will be dropped across one resistor if it has ______________. A. half the resistance of the other resistor B. a resistance equal to the other C. at least ten times the resistance of the other D. a partial short circuit

Last Answer : Answer: C

A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A

Description : A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A voltmeter having a resistance of 1.2 kOhm is connected across 600 ohm resistances and reads 5 V. The value of resistance R shall be:

Last Answer : A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A voltmeter having a resistance of 1.2 kOhm is connected across 600 ohm resistances and reads 5 V. The value of resistance R shall be: 2.4 kOhm

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is

Description : The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

Last Answer : The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is 11%

What voltage would be measured across the 45 ohm resistor?

Description : What voltage would be measured across the 45 ohm resistor?

Last Answer : Not enough information. But if you know the current, you can useOhm's Law (just multiply the resistance times the current).

If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Last Answer : 500Ω

A series circuit consists of a two ohm RESISTOR and a one ohm INDUCTOR. The relationship between current and voltage is: w) current will lag by 30 degrees. x) current will lag by 26 degrees. y) current will lead by 26 degrees. z) current will lead by 30 degrees.

Description : A series circuit consists of a two ohm RESISTOR and a one ohm INDUCTOR. The relationship between current and voltage is: w) current will lag by 30 degrees. x) current will lag by 26 degrees. y) current will lead by 26 degrees. z) current will lead by 30 degrees.

Last Answer : ANSWER: X -- CURRENT WILL LAG BY 26 DEGREES.

In a series RC circuit, 12 V (rms) is measured across.the resistor and 15 V (rms) is measured across the ...

Description : In a series RC circuit, 12 V (rms) is measured across.the resistor and 15 V (rms) is measured across the capacitor. The value of rms source voltage is: A. 3 V B. 27 V C. 19.2 V D. 1.9 V

Last Answer : In a series RC circuit, 12 V (rms) is measured across.the resistor and 15 V (rms) is measured across the capacitor. The value of rms source voltage is: 19.2 V

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Description : Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Last Answer : Answer: A

If four 90 ohm resistors are connected in series across an 18 V source, the current equals

Last Answer : If four 90 ohm resistors are connected in series across an 18 V source, the current equals 50 mA.

A series combination of resistance 100 ohm and capacitance 50µf is connected in series to a 230 V, 50HZ supply. Calculate (i) Capacitive reactance (ii) Current (iii) Power factor (iv) Power consumed

Description : A series combination of resistance 100 ohm and capacitance 50µf is connected in series to a 230 V, 50HZ supply. Calculate (i) Capacitive reactance (ii) Current (iii) Power factor (iv) Power consumed 

Last Answer : For RC series circuit

A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the proper connections for across the line starting B. the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Description : A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the ... the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Last Answer : Answer: D

The potential difference across a 4 ohm resistor is 20 volts. What is the current in the resistor?

Description : The potential difference across a 4 ohm resistor is 20 volts. What is the current in the resistor?

Last Answer : ANSWER: 5 AMPS

The potential difference across a 4 ohm resistor is 20 volts. Assuming that all of the energy dissipated by this resistor is in the form of heat, how many joules of heat are radiated in 10 seconds?

Description : The potential difference across a 4 ohm resistor is 20 volts. Assuming that all of the energy dissipated by this resistor is in the form of heat, how many joules of heat are radiated in 10 seconds?  

Last Answer : ANSWER: 1000 JOULES

The constant potential difference across a 2 ohm resistor is 20 volts. How many watts of power are dissipated by this resistor?

Description : The constant potential difference across a 2 ohm resistor is 20 volts. How many watts of power are dissipated by this resistor?

Last Answer : ANSWER: 200 WATTS

Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor

Description : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

Last Answer : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the polarity as indicated. The ratio of potential difference acro

Description : In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the polarity as indicated. The ratio of potential difference acro

Last Answer : In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the ... difference across `5Omega` and resistance `R` is

A voltage of 30 V is applied across a colour coded carbon resistor with first, second and third rings of blue, black and yellow colurs. What is the cu

Description : A voltage of 30 V is applied across a colour coded carbon resistor with first, second and third rings of blue, black and yellow colurs. What is the cu

Last Answer : A voltage of 30 V is applied across a colour coded carbon resistor with first, second and ... What is the current flowing through the resistor ?

A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)

Description : A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)

Last Answer : ANSWER: Z -- 5 V/R

If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : -

Description : If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : -  a) 15 mA b) 1.5 mA c) 10 mA d) 1 mA

Last Answer : If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : - 1.5 mA

What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Last Answer : Answer: C

In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit

Description : In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit

Last Answer : Answer: D

At what instant does the greatest voltage appear across the resistor in a series RC circuit when the capacitor is charging?

Description : At what instant does the greatest voltage appear across the resistor in a series RC circuit when the capacitor is charging?

Last Answer : At the instant of the initiation of the action.

What is the phase angle of an ohm inductor in series with an ohm resistor connected to a 5 KHz source?

Description : What is the phase angle of an ohm inductor in series with an ohm resistor connected to a 5 KHz source?

Last Answer : You need to provide values of resistor and inductor etc to find the phase angle.

A circuit has a resistance of 200 ohms. The resistance of the circuit can be reduced to 120 ohms by adding which of the following to the circuit. w) 80 ohm resistor in series x) 150 ohm resistor in parallel y) 240 ohm resistor in series z) 300 ohm resistor in parallel

Description : A circuit has a resistance of 200 ohms. The resistance of the circuit can be reduced to 120 ohms by adding which of the following to the circuit. w) 80 ohm resistor in series x) 150 ohm resistor in parallel y) 240 ohm resistor in series z) 300 ohm resistor in parallel

Last Answer : ANSWER: Z -- 300 OHM RESISTOR IN PARALLEL

A 20 ohm resistor and a 60 ohm resistor are connected in parallel to a voltage source. If the current in the 60 ohm resistor is one ampere, the current in the 20 ohm resistor will be: w) 1/3 ampere x) 2/3 ampere y) 1 ampere z) 3 amperes

Description : A 20 ohm resistor and a 60 ohm resistor are connected in parallel to a voltage source. If the current in the 60 ohm resistor is one ampere, the current in the 20 ohm resistor will be: w) 1/3 ampere x) 2/3 ampere y) 1 ampere z) 3 amperes

Last Answer : ANSWER: Z -- 3 AMPERES

What is the voltage dropped by each resistor of the circuit described in question 17?

Description : What is the voltage dropped by each resistor of the circuit described in question 17?

Last Answer : E1 = 60 volts. E2 = 180 volts. E3 = 240 volts.

An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Description : An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Last Answer : ANSWER: Z -- 200 OHMS

When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is?

Description : When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is? A.14.4 V B.1.4 V C.100 V D.10 V

Last Answer : When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is? A.14.4 V B.1.4 V C.100 V D.10 V

In the illustrated circuit 'A', what power is consumed by a 3 ohm resistor with a 12 volt source? EL-0041 A. 12 watts B. 48 watts C. 64 watts D. 232 watts

Description : In the illustrated circuit 'A', what power is consumed by a 3 ohm resistor with a 12 volt source? EL-0041 A. 12 watts B. 48 watts C. 64 watts D. 232 watts

Last Answer : Answer: B

In the illustration what is the minimum wattage needed for a 3 ohm resistor with a 12 VDC power source in circuit 'A'? EL-0041 A. 12 watts B. 48 watts C. 64 watts D. 232 watts

Description : In the illustration what is the minimum wattage needed for a 3 ohm resistor with a 12 VDC power source in circuit 'A'? EL-0041 A. 12 watts B. 48 watts C. 64 watts D. 232 watts

Last Answer : Answer: B

If the 12 Ohm resistor draws a current of 1 A as shown in the figure, the value of resistance R is

Description : If the 12 Ohm resistor draws a current of 1 A as shown in the figure, the value of resistance R is

Last Answer : If the 12 Ohm resistor draws a current of 1 A as shown in the figure, the value of resistance R is

As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100.

Description : As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is A) 25 A B) 50 A C) 100 A D) 200A

Last Answer : As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is 50 A

A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V,

Description : A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum when the supply frequency is 1 kHz. The ... (A) 40, 400 Hz (B) 10, 100 Hz (C) 20, 50 Hz (D) 50, 20 Hz

Last Answer : A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum ... supply frequency is 1 kHz. The approximate values of Q-factor and bandwidth are, respectively 20, 50 Hz

A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current

Description : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

Last Answer : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

‘Germanium diode knee voltage is lower than silicon diode knee voltage.' Justify.

Description :  ‘Germanium diode knee voltage is lower than silicon diode knee voltage.' Justify.

Last Answer : Justification: The band gap between conduction and valence band for Germanium (0.66eV) is less as compared to Silicon (1.11eV).Hence less energy is required to start conduction in Germanium diode. 

The cut-in voltage of a silicon diode is approx.

Description : The cut-in voltage of a silicon diode is approx. • 0.7 volt • 0.3 volt • 1.4 volt • None of the above.

Last Answer : The cut-in voltage of a silicon diode is approx. 0.7 volt

We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance

Description : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

Last Answer : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be 2.4 kOhm

When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage is being measured B. input impedance much less than the impedance across which the voltage is being measured C. sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Description : When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage ... sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Last Answer : Answer: A

Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Description : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Last Answer : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power ... B. 160 W C. `37.5 W` D. 60 W

Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Description : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Last Answer : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power ... `37.5` W B. 75W C. 80W D. 40 W

A permanent magnet moving coil instrument gives full scale deflection of 25mA when a voltage of 75mV is applied across it. Calculate: (i) Resistance of shunt required for full scale deflection of 150 A. (ii) Series resistance for full scale deflection of 500 V.

Description : A permanent magnet moving coil instrument gives full scale deflection of 25mA when a voltage of 75mV is applied across it. Calculate: (i) Resistance of shunt required for full scale deflection of 150 A. (ii) Series resistance for full scale deflection of 500 V.

Last Answer : Answer :

In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage

Description : In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage across RLC is 15 V. What is the voltage across C?

Last Answer : In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage across RLC is 15 V. What is the voltage across C? 7 V

What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively?

Description : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

Last Answer : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured...

Description : A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured across all the resistors except the third resistor. The voltage across the third resistor is: A. 0 V B. 1.2V C. 6V D. 0.6V

Last Answer : A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured across all the resistors except the third resistor. The voltage across the third resistor is: 6V