Hoop shrinking in thick cylinders is done to achieve (a) Increased stresses (b) Decreased stresses (c ) Uniform stresses (d) None

Hoop shrinking in thick cylinders is done to achieve
(a) Increased stresses
(b) Decreased stresses
(c ) Uniform stresses
(d) None
by

2 Answers

Answer :

(c ) Uniform stresses
by

Answer :

Hoop shrinking technique is used to make the stresses on the cylinder walls evenly distributed around the circumference of the cylinder, which results in a uniform stress distribution. This is important for maintaining structural integrity and preventing failure of the cylinder under load. It also makes sure that the cylinder can withstand the pressure inside it.
by

Related questions

The thick shell is made from laminations to get (a) Increased stresses (b) Decreased stresses (c) Uniform stresses (d) None

Description : The thick shell is made from laminations to get (a) Increased stresses (b) Decreased stresses (c) Uniform stresses (d) None

Last Answer : (c) Uniform stresses

Design of a thin shell under pressure is done on the basis of a. Radial stress b. Longitudinal stress c. Hoop stress d. All the three stresses

Description : Design of a thin shell under pressure is done on the basis of a. Radial stress b. Longitudinal stress c. Hoop stress d. All the three stresses

Last Answer : c. Hoop stress

What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Description : What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Last Answer : c. 1:2

A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.

Description : A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.

Last Answer : c) 210 MPa

In a thick-cylinder pressurized from inside, the hoop stress is maximum at a) The center of the wall thickness b) the outer radius c) the inner radius d) both the inner and the outer radii

Description : In a thick-cylinder pressurized from inside, the hoop stress is maximum at a) The center of the wall thickness b) the outer radius c) the inner radius d) both the inner and the outer radii

Last Answer : c) the inner radius

Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Description : Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Last Answer : b) Thick Cylinders

Lame's theory is associated with a) thick cylindrical shells b) thin cylindrical shells c) direct and bending stresses d) none of these

Description : Lame's theory is associated with a) thick cylindrical shells b) thin cylindrical shells c) direct and bending stresses d) none of these

Last Answer : a) thick cylindrical shells

Which one is most important in a thin shell? a) d/t <20 b) d/t> 10 c) Stresses are uniform d) None

Description : Which one is most important in a thin shell? a) d/t 10 c) Stresses are uniform d) None

Last Answer : c) Stresses are uniform

A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above

Description : A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above

Last Answer : b. Stresses are uniform over the entire thickness

Which of the following is least likely to be an effect of global warming? (1 ) Increased frequency of hurricanes (2) Loss of fertile delta region as for agriculture (3) Decreased rate of photosynthesis in vegetation (4) Shrinking of the polar ice regions

Description : Which of the following is least likely to be an effect of global warming? (1 ) Increased frequency of hurricanes (2) Loss of fertile delta region as for agriculture (3) Decreased rate of photosynthesis in vegetation (4) Shrinking of the polar ice regions

Last Answer : (3) Decreased rate of photosynthesis in vegetation Explanation: Global warming is the current increase in temperature of the Earth's surface (both land and water) as well as it's atmosphere. ... . However, the gradual heating of Earth's surface, oceans and atmosphere will not affect photosynthesis.

Which of the following is least likely to be an effect of global warming? (1) Increased frequency of hurricanes (2) Loss of fertile delta region as for agriculture (3) Decreased rate of photosynthesis in vegetation (4) Shrinking of the polar ice regions

Description : Which of the following is least likely to be an effect of global warming? (1) Increased frequency of hurricanes (2) Loss of fertile delta region as for agriculture (3) Decreased rate of photosynthesis in vegetation (4) Shrinking of the polar ice regions

Last Answer : Decreased rate of photosynthesis in vegetation

A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately a. increased by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Description : A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number ... by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Last Answer : a. increased by 8 times

Hoop strain in a thin shell is a) σh /E b) σl /E c) 3 σh /E d) None

Description : Hoop strain in a thin shell is a) σh /E b) σl /E c) 3 σh /E d) None

Last Answer : d) None

Which stress is the least in a thin shell a. Longitudinal stress b. Hoop stress c. Radial stress d. None

Description : Which stress is the least in a thin shell a. Longitudinal stress b. Hoop stress c. Radial stress d. None

Last Answer : c. Radial stress

Hoop stress in a thin vessel is a. pD/2t b. pD/4t c. pD/3t d. None

Description : Hoop stress in a thin vessel is a. pD/2t b. pD/4t c. pD/3t d. None

Last Answer : a. pD/2t

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Last Answer : (a) Fatigue Failure

Propagation of fatigue failure is always due to compressive stresses. (a) Due to bending (b) Due to tensile (c) Due to fatigue (d) None of the listed

Description : Propagation of fatigue failure is always due to compressive stresses. (a) Due to bending (b) Due to tensile (c) Due to fatigue (d) None of the listed

Last Answer : (b) Due to tensile

eaf springs are designed on the basis of (a) Maximum bending stresses (b) Maximum deflection (c) Maximum bending as well as maximum deflection (d) None

Description : eaf springs are designed on the basis of (a) Maximum bending stresses (b) Maximum deflection (c) Maximum bending as well as maximum deflection (d) None

Last Answer : (c) Maximum bending as well as maximum deflection

A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None

Description : A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None

Last Answer : (b) Shear stresses

Stresses in a thin cylindrical shell under internal pressure is independent of a. Diameter b. Thickness c. Length d. Diameter and thickness

Description : Stresses in a thin cylindrical shell under internal pressure is independent of a. Diameter b. Thickness c. Length d. Diameter and thickness

Last Answer : c. Length

Keeping loading same but increasing the length, normal stresses in a long column will (a) Increase (b) Decrease (c) No change (d) None

Description : Keeping loading same but increasing the length, normal stresses in a long column will (a) Increase (b) Decrease (c) No change (d) None

Last Answer : (b) Decrease

Keeping loading same but increasing the length, shear stresses in a beam will (a) Increase (b) Decrease (c) No change (d) None

Description : Keeping loading same but increasing the length, shear stresses in a beam will (a) Increase (b) Decrease (c) No change (d) None

Last Answer : (c) No change

Keeping loading same but increasing the length, normal stresses in a beam will (a) Increase (b) Decrease (c) No change (d) None

Description : Keeping loading same but increasing the length, normal stresses in a beam will (a) Increase (b) Decrease (c) No change (d) None

Last Answer : (a) Increase

Nature of stresses produced in buckling and bending are (a) Same (b) Different (c) Only tensile (d) None

Description : Nature of stresses produced in buckling and bending are (a) Same (b) Different (c) Only tensile (d) None

Last Answer : (a) Same

In shafts with keyways the allowable stresses are usually ------------ proportional to the twisting moment. a.25% b. 50% c. 75% d. 95%

Description : In shafts with keyways the allowable stresses are usually ------------ proportional to the twisting moment. a.25% b. 50% c. 75% d. 95%

Last Answer : c. 75%

Ratio of diameters of two shafts joined in series is 2. If the two shafts have the same material and the same length the ratio of their shear stresses is a. 2 b. 4 c. 8 d. 16

Description : Ratio of diameters of two shafts joined in series is 2. If the two shafts have the same material and the same length the ratio of their shear stresses is a. 2 b. 4 c. 8 d. 16

Last Answer : c. 8

Tensile and compressive stresses in a beam of symmetrical section are (a) σt = σc (b) σt > σc (c) σt < σc (d) None

Description : Tensile and compressive stresses in a beam of symmetrical section are (a) σt = σc (b) σt > σc (c) σt < σc (d) None

Last Answer : (a) σt = σc

Variation of bending stresses in a beam have (a) Parabolic variation (b) Linear variation (c) Cubical variation (d) None

Description : Variation of bending stresses in a beam have (a) Parabolic variation (b) Linear variation (c) Cubical variation (d) None

Last Answer : (b) Linear variation

Tensile and compressive stresses in a beam of un-symmetrical section are (a) σt = σc (b) σt =0 (c) σc =0 (d) None

Description : Tensile and compressive stresses in a beam of un-symmetrical section are (a) σt = σc (b) σt =0 (c) σc =0 (d) None

Last Answer : (d) None

Tensile and compressive stresses in a beam of symmetrical section are (a) σt = σc (b) σt > σc (c) σt < σc (d) None

Description : Tensile and compressive stresses in a beam of symmetrical section are (a) σt = σc (b) σt > σc (c) σt < σc (d) None

Last Answer : (a) σt = σc

In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum at the inner surface and minimum at the outer surface c) maximum at the inner surface and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Description : In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum ... and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Last Answer : c) maximum at the inner surface and zero at the outer surface

A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Description : A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Last Answer : b) 1.5 kg/cm2

The maximum strain in a thick cylinder under pi will be a) σh/E+μ σl/E b) σh/ E+ μσr/E c) σr/E+μ σl/E d) None

Description : The maximum strain in a thick cylinder under pi will be a) σh/E+μ σl/E b) σh/ E+ μσr/E c) σr/E+μ σl/E d) None

Last Answer : b) σh/ E+ μσr/E

A thick cylinder under pi and po will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Description : A thick cylinder under pi and po will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Last Answer : 2. Inner radius

A thick cylinder under internal fluid pressure’ pi will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Description : A thick cylinder under internal fluid pressure’ pi will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Last Answer : 2. Inner radius

A thick cylinder under external fluid pressure’ p0′ will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Description : A thick cylinder under external fluid pressure’ p0′ will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Last Answer : 2. Inner radius

Which stress is constant in a thick shell a) σh b) σl c) σr d) None

Description : Which stress is constant in a thick shell a) σh b) σl c) σr d) None

Last Answer : b) σl

Maximum shear stress in a thick shell is a) (σh+ σl)/2 b) (σh+ σr)/2 c) (σh– σl)/2 d) None

Description : Maximum shear stress in a thick shell is a) (σh+ σl)/2 b) (σh+ σr)/2 c) (σh– σl)/2 d) None

Last Answer : b) (σh+ σr)/2

In a thick shell which stress is negligible a) σh b) σl c) σr d) None

Description : In a thick shell which stress is negligible a) σh b) σl c) σr d) None

Last Answer : b) σl

The type of spring used to achieve any linear and non-linear load-deflection characteristics is (a)spiral spring (b) non-ferrous spring (c)Belleville spring (d) torsion spring

Description : The type of spring used to achieve any linear and non-linear load-deflection characteristics is (a)spiral spring (b) non-ferrous spring (c)Belleville spring (d) torsion spring

Last Answer : (c)Belleville spring

The type of spring used to achieve greater load carrying capacity within given space is (a)spiral spring (b) springs in series (c)multi-leaf spring (d) concentric spring

Description : The type of spring used to achieve greater load carrying capacity within given space is (a)spiral spring (b) springs in series (c)multi-leaf spring (d) concentric spring

Last Answer : (d) concentric spring

For a cold dilute feed to produce thick viscous liquor, backward feeding as compared to forward feeding results in (A) Increased economy (B) Decreased economy (C) Lower capacity (D) No effect on economy

Description : For a cold dilute feed to produce thick viscous liquor, backward feeding as compared to forward feeding results in (A) Increased economy (B) Decreased economy (C) Lower capacity (D) No effect on economy

Last Answer : (A) Increased economy

In order to achieve economy, the spacing of stirrups at mid span section---------- compared to that of support section [ A ] May be decreased [ B ] May be increased [ C ] Must be kept equal [ D ] None of the above.

Description : In order to achieve economy, the spacing of stirrups at mid span section---------- compared to that of support section [ A ] May be decreased [ B ] May be increased [ C ] Must be kept equal [ D ] None of the above.

Last Answer : [ B ] May be increased

The laminated springs are given initial curvature (a) To have uniform strength (b) To make it more economical (c) So that plates may become flat, when subjected to design load (d) None of these

Description : The laminated springs are given initial curvature (a) To have uniform strength (b) To make it more economical (c) So that plates may become flat, when subjected to design load (d) None of these

Last Answer : (c) So that plates may become

The laminated springs are given initial curvature (a) To have uniform strength (b) To make it more economical (c) So that plates may become flat, when subjected to design load (d) None of these

Description : The laminated springs are given initial curvature (a) To have uniform strength (b) To make it more economical (c) So that plates may become flat, when subjected to design load (d) None of these

Last Answer : (c) So that plates may become flat, when subjected to design load

The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose endsare hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2, the permissible maximumcrippling load will be (a) 1.288 tonnes (b) 12.88 (c) 128.8 tonnes (d) 288.0

Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose endsare hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2, the permissible maximumcrippling load will be (a) 1.288 tonnes (b) 12.88 (c) 128.8 tonnes (d) 288.0

Last Answer : (b) 12.88

A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Description : A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Last Answer : d.16.27 mm.

Which of the following assumptions are made in torsion theory? a. Shaft is perfectly straight b. Material of the shaft is heterogeneous c. Twist cannot be uniform along the length of the shaft d. Shaft is perfectly curve

Description : Which of the following assumptions are made in torsion theory? a. Shaft is perfectly straight b. Material of the shaft is heterogeneous c. Twist cannot be uniform along the length of the shaft d. Shaft is perfectly curve v

Last Answer : a. Shaft is perfectly straight b. Material of the shaft is heterogeneous

The shear stress varies from centre to the surface of the shaft with (a) Uniform rate (b) Varying rate (c) Remains same (d) None of these

Description : The shear stress varies from centre to the surface of the shaft with (a) Uniform rate (b) Varying rate (c) Remains same (d) None of these

Last Answer : (a) Uniform rate

The variation of shear stress in a circular shaft subjected to torsion is a. Linear b. Parabolic c. Hyperbolic. d. Uniform

Description : The variation of shear stress in a circular shaft subjected to torsion is a. Linear b. Parabolic c. Hyperbolic. d. Uniform

Last Answer : a. Linear