Propagation of fatigue failure is always due to compressive stresses. (a) Due to bending (b) Due to tensile (c) Due to fatigue (d) None of the listed

Propagation of fatigue failure is always due to compressive stresses. (a) Due to bending (b) Due to tensile (c) Due to fatigue (d) None of the listed
by

1 Answer

Answer :

(b) Due to tensile
by

Related questions

Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed

Description : Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed

Last Answer : b) Due to tensile

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Last Answer : (a) Fatigue Failure

Tensile and compressive stresses in a beam of symmetrical section are (a) σt = σc (b) σt > σc (c) σt < σc (d) None

Description : Tensile and compressive stresses in a beam of symmetrical section are (a) σt = σc (b) σt > σc (c) σt < σc (d) None

Last Answer : (a) σt = σc

Tensile and compressive stresses in a beam of un-symmetrical section are (a) σt = σc (b) σt =0 (c) σc =0 (d) None

Description : Tensile and compressive stresses in a beam of un-symmetrical section are (a) σt = σc (b) σt =0 (c) σc =0 (d) None

Last Answer : (d) None

Tensile and compressive stresses in a beam of symmetrical section are (a) σt = σc (b) σt > σc (c) σt < σc (d) None

Description : Tensile and compressive stresses in a beam of symmetrical section are (a) σt = σc (b) σt > σc (c) σt < σc (d) None

Last Answer : (a) σt = σc

A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None

Description : A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None

Last Answer : (b) Shear stresses

Nature of stresses produced in buckling and bending are (a) Same (b) Different (c) Only tensile (d) None

Description : Nature of stresses produced in buckling and bending are (a) Same (b) Different (c) Only tensile (d) None

Last Answer : (a) Same

In a simply supported beam loaded with U.D.L over the whole section, the bending stress is …………. at top and ………….. at bottom. (a) Compressive, tensile (b) Tensile, compressive (c) Tensile, zero (d) Compressive, zero

Description : In a simply supported beam loaded with U.D.L over the whole section, the bending stress is …………. at top and ………….. at bottom. (a) Compressive, tensile (b) Tensile, compressive (c) Tensile, zero (d) Compressive, zero

Last Answer : (a) Compressive, tensile

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Last Answer : a) Fatigue Failure

Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Description : Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Last Answer : (iv)None

Parallel fillet welds are under  Shear and bending stresses  Compressive and torsion shear stresses  Tensile and compressive stresses  None

Description : Parallel fillet welds are under  Shear and bending stresses  Compressive and torsion shear stresses  Tensile and compressive stresses  None

Last Answer :  None

Fatigue failure of a material results from __________ stress. (A) Tensile (B) Compressive (C) Fluctuating (D) None of these

Description : Fatigue failure of a material results from __________ stress. (A) Tensile (B) Compressive (C) Fluctuating (D) None of these

Last Answer : (C) Fluctuating

Fatigue failure of a material may occur, when it is subjected to __________ stress. (A) Fluctuating(B) Tensile(C) Compressive(D) Torsion

Description : Fatigue failure of a material may occur, when it is subjected to __________ stress. (A) Fluctuating (B) Tensile (C) Compressive (D) Torsion

Last Answer : (A) Fluctuating

Which property is not required for shaft materials? a. High shear and tensile strength b. Good mach inability c. High fatigue strength d. Good cast ability

Description : Which property is not required for shaft materials? a. High shear and tensile strength b. Good mach inability c. High fatigue strength d. Good cast ability

Last Answer : d. Good cast ability

A transmission shaft subjected to bending loads must be designed on the basis of (a) maximum normal stress theory (b) maximum shear stress theory (c) maximum normal stress and maximum shear stress theories (d) fatigue strength

Description : A transmission shaft subjected to bending loads must be designed on the basis of (a) maximum normal stress theory (b) maximum shear stress theory (c) maximum normal stress and maximum shear stress theories (d) fatigue strength

Last Answer : (a) maximum normal stress theory

eaf springs are designed on the basis of (a) Maximum bending stresses (b) Maximum deflection (c) Maximum bending as well as maximum deflection (d) None

Description : eaf springs are designed on the basis of (a) Maximum bending stresses (b) Maximum deflection (c) Maximum bending as well as maximum deflection (d) None

Last Answer : (c) Maximum bending as well as maximum deflection

Lame's theory is associated with a) thick cylindrical shells b) thin cylindrical shells c) direct and bending stresses d) none of these

Description : Lame's theory is associated with a) thick cylindrical shells b) thin cylindrical shells c) direct and bending stresses d) none of these

Last Answer : a) thick cylindrical shells

Variation of bending stresses in a beam have (a) Parabolic variation (b) Linear variation (c) Cubical variation (d) None

Description : Variation of bending stresses in a beam have (a) Parabolic variation (b) Linear variation (c) Cubical variation (d) None

Last Answer : (b) Linear variation

The type of stress induced in a closed coiled helical tension spring is a. tensile b. compressive c. torsional shear d. tensile and compressive

Description : The type of stress induced in a closed coiled helical tension spring is a. tensile b. compressive c. torsional shear d. tensile and compressive

Last Answer : c. torsional shear

A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None

Description : A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None

Last Answer : c. Principal tensile stress

The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, is (a) One-half of the radius (b) One-third of the radius (c) One-quarter of the radius (d) One-fifth of the radius

Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (c) One-quarter of the radius (d) One-fifth of the radius

Last Answer : (c) One-quarter of the radius

A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None

Description : A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None

Last Answer : (c) Shear considerations only

It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting

Description : It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting

Last Answer : b) Tensile

When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Description : When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Last Answer : c) Shear stress

When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above

Description : When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above

Last Answer : (b) Compressive

When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature

Description : When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature

Last Answer : (d) Temperature

The value of Poison’s ratio depends upon (a) Nature of load, tensile or compressive (b) Magnitude of load (c) Material of the test specimen (d) Dimensions of the test specimen

Description : The value of Poison’s ratio depends upon (a) Nature of load, tensile or compressive (b) Magnitude of load (c) Material of the test specimen (d) Dimensions of the test specimen

Last Answer : (c) Material of the test specimen

When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ

Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ

Last Answer : b) 32M/πdᵌ

__________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength. (A) Lancing (B) Shot peening (C) Slugging (D) Spinning

Description : __________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength. (A) Lancing (B) Shot peening (C) Slugging (D) Spinning

Last Answer : (B) Shot peening

A member which is subjected to reversible tensile or compressive stress may fail at a stress lower than the ultimate stress of the material. This property of metal, is called (A) Plasticity of the metal (B) Elasticity of the metal (C) Fatigue of the metal (D) Workability of the metal

Description : A member which is subjected to reversible tensile or compressive stress may fail at a stress lower  than the ultimate stress of the material. This property of metal, is called  (A) Plasticity of the ... ) Elasticity of the metal  (C) Fatigue of the metal  (D) Workability of the metal

Last Answer : (C) Fatigue of the metal

Cotter joint is employed when the members are subjected to which sort of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the above

Description : Cotter joint is employed when the members are subjected to which sort of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the above

Last Answer : c) Axial tensile or compressive

Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned

Description : Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned

Last Answer : c) Axial tensile or compressive

In the analysis, all the principal stresses are assumed as a. Shear stresses b. Compressive stresses c. Tensile stresses d. None

Description : In the analysis, all the principal stresses are assumed as a. Shear stresses b. Compressive stresses c. Tensile stresses d. None

Last Answer : c. Tensile stresses

Nature of the three principal stresses is a. Firstly All tensile b. Secondly All compressive c. Thirdly All shear d. None

Description : Nature of the three principal stresses is a. Firstly All tensile b. Secondly All compressive c. Thirdly All shear d. None

Last Answer : a. Firstly All tensile

The equations for principal stresses are valid only when (a)σ x and σ y are both tensile (b) σ x is compressive and σ y is tensile (c) σ x is tensile and σ y is compressive (d) None

Description : The equations for principal stresses are valid only when (a)σ x and σ y are both tensile (b) σ x is compressive and σ y is tensile (c) σ x is tensile and σ y is compressive (d) None

Last Answer : (a)σ x and σ y are both tensile

A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is (A) bn (fc /2) (d - n/3) (B) Atft (d - n/3) (C) ½ n1 (1 - n1/3) cbd² (D) All the above

Description : A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is (A) bn (fc ... (B) Atft (d - n/3) (C) ½ n1 (1 - n1/3) cbd² (D) All the above

Last Answer : Answer: Option D

If the permissible compressive and tensile stresses in a singly reinforced beam are 50 kg/cm2 and 1400 kg/cm2 respectively and the modular ratio is 18, the percentage area At of the steel required for an economic section, is (A) 0.496 % (B) 0.596 % (C) 0.696 % (D) 0.796 %

Description : If the permissible compressive and tensile stresses in a singly reinforced beam are 50 kg/cm2 and 1400 kg/cm2 respectively and the modular ratio is 18, the percentage area At of the steel required for an economic section, is (A) 0.496 % (B) 0.596 % (C) 0.696 % (D) 0.796 %

Last Answer : Answer: Option C

In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Description : In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Last Answer : Answer: Option D

The purpose of reinforcement in pre-stressed concrete is (A) To provide adequate bond stress (B) To resist tensile stresses (C) To impart initial compressive stress in concrete (D) All of the above

Description : The purpose of reinforcement in pre-stressed concrete is (A) To provide adequate bond stress (B) To resist tensile stresses (C) To impart initial compressive stress in concrete (D) All of the above

Last Answer : Answer: Option C

The longitudinal shearing stresses acting on the surface between the steel and concrete are called. (a) Bond stress (b) Tensile stresses (c) Compressive stresses (d) None of these

Description : The longitudinal shearing stresses acting on the surface between the steel and concrete are called. (a) Bond stress (b) Tensile stresses (c) Compressive stresses (d) None of these

Last Answer : (a) Bond stress

Reinforced cement concrete is equally strong in taking (a) Tensile and compressive stress (b) Compressive and shear stresses. (c) Tensile, compressive and shear stresses. (d) Tensile and shear stresses.

Description : Reinforced cement concrete is equally strong in taking (a) Tensile and compressive stress (b) Compressive and shear stresses. (c) Tensile, compressive and shear stresses. (d) Tensile and shear stresses.

Last Answer : (c) Tensile, compressive and shear stresses.

While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (A) Direct shear stress

The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure. a) Fracture b) Fatigue c) Yielding d) None of the mentioned

Description : The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure. a) Fracture b) Fatigue c) Yielding d) None of the mentioned

Last Answer : b) Fatigue

During transverse vibrations, shaft is subjected to which type of stresses? A) Tensile stresses B) Torsional shear stress C) Bending stresses D) All of the above

Description : During transverse vibrations, shaft is subjected to which type of stresses? A) Tensile stresses B) Torsional shear stress C) Bending stresses D) All of the above

Last Answer : C) Bending stresses

During transverse vibrations, shaft is subjected to which type of stresses? a. Tensile stresses b. Torsional shear stress c. Bending stresses d. All of the above

Description : During transverse vibrations, shaft is subjected to which type of stresses? a. Tensile stresses b. Torsional shear stress c. Bending stresses d. All of the above

Last Answer : c. Bending stresses

The application of elastic theory to the beams is based on the assumption that (a) At any cross-section, plane sections before bending remain plane after bending (b) All tensile stresses are taken up by reinforcement alone and none by the concrete. (c) Steel reinforcement is free from initial stresses when it is embedded in concrete. (d) All of the above

Description : The application of elastic theory to the beams is based on the assumption that (a) At any cross-section, plane sections before bending remain plane after bending (b) All tensile stresses are taken ... reinforcement is free from initial stresses when it is embedded in concrete. (d) All of the above

Last Answer : (d) All of the above

Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed

Description : Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed

Last Answer : b) Tensile

Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed

Description : Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed

Last Answer : b) Tensile

The underground sewers are more subjected to A. Tensile force B. Compressive force C. Bending force D. Shearing force

Description : The underground sewers are more subjected to A. Tensile force B. Compressive force C. Bending force D. Shearing force

Last Answer : ANS: B

The rim of the flywheel is subjected to, 1. direct tensile stress and bending stress 2. torsional shear stress and bending stress 3. direct shear stress and bending stress 4. compressive stress and bending stress

Description : The rim of the flywheel is subjected to, 1. direct tensile stress and bending stress 2. torsional shear stress and bending stress 3. direct shear stress and bending stress 4. compressive stress and bending stress

Last Answer : 1. direct tensile stress and bending stress