The ultimate tensile strength of structural mild steel is about (A) 160 N/mm² (B) 260 N/mm² (C) 420 N/mm² (D) 520 N/mm2

The ultimate tensile strength of structural mild steel is about
(A) 160 N/mm²
(B) 260 N/mm²
(C) 420 N/mm²
(D) 520 N/mm
by

1 Answer

Answer :

Answer: Option C
by

Related questions

A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 × 106 N/mm2 , the depth of the joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm

Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so  that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the  value of E = 0.2 ... joist, is  (A) 200 mm  (B) 250 mm  (C) 300 mm  (D) 400 mm 

Last Answer : (D) 400 mm 

The allowable tensile stress in mild steel stirrups, reinforced cement concrete, is(A) 1400 kg/cm2(B) 190 kg/cm2(C) 260 kg/cm2(D) 230 kg/cm

Description : The allowable tensile stress in mild steel stirrups, reinforced cement concrete, is (A) 1400 kg/cm2 (B) 190 kg/cm2 (C) 260 kg/cm2 (D) 230 kg/cm

Last Answer : Answer: Option A

A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2 , the tensile force developed at a temperature of 50°C, is (A) 80 N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option

Description : A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the  ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2  MN/mm2 , the ... N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option 

Last Answer : (C) 120 N/mm

Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)

Description : Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)

Last Answer : Answer: Option D

The permissible diagonal tensile stress in reinforced brick work is (A) About 0.1 N/mm² (B) Zero (C) 0.3 N/mm² to 0.7 N/mm² (D) About 1.0 N/m2

Description : The permissible diagonal tensile stress in reinforced brick work is (A) About 0.1 N/mm² (B) Zero (C) 0.3 N/mm² to 0.7 N/mm² (D) About 1.0 N/m2

Last Answer : Answer: Option A

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Last Answer : c) 8mm

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm

Last Answer : a) 540mm

As per IS: 1139, permissible stress in compression steel reinforcement for High Yield strength deformed bars is [ A ] 140 N/mm2 [ B ] 190 N/mm2 [ C ] 230 N/mm2 [ D ] 415 N/mm2

Description : As per IS: 1139, permissible stress in compression steel reinforcement for High Yield strength deformed bars is [ A ] 140 N/mm2 [ B ] 190 N/mm2 [ C ] 230 N/mm2 [ D ] 415 N/mm2

Last Answer : [ B ] 190 N/mm2

The ultimate average anchorage bond stress for plain bars in tension is _______ if the grade of concrete is M20 [ A ] 1.60 N/mm2 [ B ] 1.92 N/mm2 [ C ] 2.24 N/mm2 [ D ] 2.40 N/mm2

Description : The ultimate average anchorage bond stress for plain bars in tension is _______ if the grade of concrete is M20 [ A ] 1.60 N/mm2 [ B ] 1.92 N/mm2 [ C ] 2.24 N/mm2 [ D ] 2.40 N/mm2

Last Answer : [ B ] 1.92 N/mm2

The ultimate average anchorage bond stress for plain bars in tension is _______ if the grade of concrete is M20 [ A ] 1.60 N/mm2 [ B ] 1.92 N/mm2 [ C ] 2.24 N/mm2 [ D ] 2.40 N/mm2

Description : The ultimate average anchorage bond stress for plain bars in tension is _______ if the grade of concrete is M20 [ A ] 1.60 N/mm2 [ B ] 1.92 N/mm2 [ C ] 2.24 N/mm2 [ D ] 2.40 N/mm2

Last Answer : [ B ] 1.92 N/mm2

Crushing strength of a first class brick should not be less than (A) 3.5 N/mm² (B) 7.0 N/mm² (C) 10.5 N/mm² (D) 14.0 N/mm²

Description : Crushing strength of a first class brick should not be less than (A) 3.5 N/mm² (B) 7.0 N/mm² (C) 10.5 N/mm² (D) 14.0 N/mm²

Last Answer : Answer: Option C

When the steel is subjected to normalising, its __________ decreases. (A) Yield point (B) Ductility (C) Ultimate tensile strength (UTS)

Description : When the steel is subjected to normalising, its __________ decreases. (A) Yield point (B) Ductility (C) Ultimate tensile strength (UTS)

Last Answer : (B) Ductility

Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron Answer: Option C

Description : Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron Answer: Option C

Last Answer : (C) Cast iron

With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Description : With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Last Answer : (A) Impact strength

Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron

Description : Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron

Last Answer : Option B

As per IS;456, in working stress method of design, permissible tensile stress for M20 grade concrete is given by [ A ] 1. 2 N/mm2 [ B ] 1.5 N/mm2 [ C ] 2.0 N/mm2 [ D ] 2.8 N/mm2

Description : As per IS;456, in working stress method of design, permissible tensile stress for M20 grade concrete is given by [ A ] 1. 2 N/mm2 [ B ] 1.5 N/mm2 [ C ] 2.0 N/mm2 [ D ] 2.8 N/mm2

Last Answer : [ D ] 2.8 N/mm2

Modulus of elasticity of steel as per IS: 4561978 shall be taken as (A) 20 kN/cm² (B) 200 kN/cm² (C) 200 kN/mm² (D) 2 × 106 N/cm2

Description : Modulus of elasticity of steel as per IS: 4561978 shall be taken as (A) 20 kN/cm² (B) 200 kN/cm² (C) 200 kN/mm² (D) 2 × 106 N/cm2

Last Answer : Answer: Option C

If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also

Description : If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also

Last Answer : Answer: Option B

Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild steel bar in tension from initial zero strain to failure is (a) 4, 1, 2, 3 and 5 (b) 1, 4, 3, 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5

Description : Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild ... , 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5

Last Answer : (c) 4, 1, 3, 5 and 2

The curvature of the earth's surface, is taken into account only if the extent of survey is more than (A) 100 sq km (B) 160 sq km (C) 200 sq km (D) 260 sq km

Description : The curvature of the earth's surface, is taken into account only if the extent of survey is more than (A) 100 sq km (B) 160 sq km (C) 200 sq km (D) 260 sq km

Last Answer : (D) 260 sq km

A school has 4 sections of class 12, such that half the number of students of 1st section, 1/3rd of 2nd section, 1/4th of 3rd section and 1/5th of the 4th section are equal. If total number of students in class 12 is 420, find the number of students in sections 1st and 2nd. A) 180 B) 120 C) 240 D) 150 E) 260

Description : A school has 4 sections of class 12, such that half the number of students of 1st section, 1/3rd of 2nd section, 1/4th of 3rd section and 1/5th of the 4th section are equal. If total number of students in ... find the number of students in sections 1st and 2nd. A) 180 B) 120 C) 240 D) 150 E) 260

Last Answer : Answer: D Let number of students in 4 sections be A, B, C, D respectively. Then 1/2 of A = 1/3 of b = 1/4 of C = 1/5 of D So A : B : C : D = 2 : 3 : 4 : 5 [When A/2 = B/3 = C/4, then ratio A: B : C = 2 : 3 : 4] So students in 1st and 2nd section = [(2+3)/(2+3+4+5)] * 420 = 150

Mild steel is used for (A) Structural works in beams, joints and girders (B) Small sized water pipes (C) Columns and struts (D) None of these

Description : Mild steel is used for (A) Structural works in beams, joints and girders (B) Small sized water pipes (C) Columns and struts (D) None of these

Last Answer : Answer: Option A

Select the correct statement (A) Elastic modulus of high tensile steel is nearly the same as that of mild steel (B) Elastic modulus of high tensile steel is more than that of mild steel (C) Carbon percentage in high carbon steel is less than that in mild steel (D) High tensile steel is cheaper than mild steel

Description : Select the correct statement (A) Elastic modulus of high tensile steel is nearly the same as that of mild steel (B) Elastic modulus of high tensile steel is more than that of mild steel (C) ... high carbon steel is less than that in mild steel (D) High tensile steel is cheaper than mild steel

Last Answer : Answer: Option A

Which of the following stresses is used for identifying the quality of structural steel? (A) Ultimate stress (B) Yield stress (C) Proof stress (D) None of the abov

Description : Which of the following stresses is used for identifying the quality of structural steel? (A) Ultimate stress (B) Yield stress (C) Proof stress (D) None of the above

Last Answer : Answer: Option B

If yielding strength=400N/mm², the find the permissible shear stress according to ASME standards. a) 72 N/mm² b) 76 N/mm² c) 268 N/mm² d) 422 N/mm²

Description : If yielding strength=400N/mm², the find the permissible shear stress according to ASME standards. a) 72 N/mm² b) 76 N/mm² c) 268 N/mm² d) 422 N/mm²

Last Answer : a) 72 N/mm²

For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above

Description : For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above

Last Answer : Answer: Option D

The compressive strength an ordinary Portland cement (1:3) after 7 days test should not be less than. (a) 11N/mm2 (b) 17.5 N/mm2 (c) 22 N/mm2 (d) 27.5N/m2

Description : The compressive strength an ordinary Portland cement (1:3) after 7 days test should not be less than. (a) 11N/mm2 (b) 17.5 N/mm2 (c) 22 N/mm2 (d) 27.5N/m2

Last Answer : (b) 17.5 N/mm2

As per IS:1139, the characteristic yield strength for cold twisted deformed bars is [ A ] 250 N/mm2 [ B ] 415 N/mm2 [ C ] 500 N/mm2 [ D ] 550 N/mm2

Description : As per IS:1139, the characteristic yield strength for cold twisted deformed bars is [ A ] 250 N/mm2 [ B ] 415 N/mm2 [ C ] 500 N/mm2 [ D ] 550 N/mm2

Last Answer : [ C ] 500 N/mm2

As per IS:1139, the characteristic yield strength for hot rolled High yield strength deformed bars is [ A ] 250 N/mm2 [ B ] 415 N/mm2 [ C ] 500 N/mm2 [ D ] 550 N/mm2

Description : As per IS:1139, the characteristic yield strength for hot rolled High yield strength deformed bars is [ A ] 250 N/mm2 [ B ] 415 N/mm2 [ C ] 500 N/mm2 [ D ] 550 N/mm2

Last Answer : [ B ] 415 N/mm2

Minimum compressive strength of cement required at the age of 3 days for ordinary Portland cement of grade 33 is [ A ] 1.15 N/mm2 [ B ] 11.5 N/mm2 [ C ] 2.10 N/mm2 [ D ] 21 N/mm2

Description : Minimum compressive strength of cement required at the age of 3 days for ordinary Portland cement of grade 33 is [ A ] 1.15 N/mm2 [ B ] 11.5 N/mm2 [ C ] 2.10 N/mm2 [ D ] 21 N/mm2

Last Answer : [ B ] 11.5 N/mm2

In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Description : In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Last Answer : b) 450 N/mm2

A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm

Description : A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm

Last Answer : b) 2.5cm

A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2 MN/mm2 and Poisson's ratio is 0.25, the change in the volume of the bar is: (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm

Description : A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2  MN/mm2  and Poisson's ratio is 0.25, the change in the volume of the bar is:  (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm

Last Answer : (C) 3.125 cm

A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the bar, is (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm

Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a  load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending  strain energy stored in the ... (A) 411 N mm  (B) 511 N mm  (C) 611 N mm  (D) 711 N mm 

Last Answer : (C) 611 N mm 

If a concrete column 200 × 200 mm in cross-section is reinforced with four steel bars of 1200 mm2 total cross-sectional area. Calculate the safe load for the column if permissible stress in concrete is 5 N/mm2 and Es is 15 Ec (A) 264 MN (B) 274 MN (C) 284 MN (D) 294 MN

Description : If a concrete column 200 200 mm in cross-section is reinforced with four steel bars of 1200  mm2  total cross-sectional area. Calculate the safe load for the column if permissible stress in  concrete is 5 N/mm2 ... 15 Ec (A) 264 MN  (B) 274 MN  (C) 284 MN  (D) 294 MN 

Last Answer : (C) 284 MN 

A spring of mean radius 40 mm contains 8 action coils of steel (N = 80000 N/mm2 ), 4 mm in diameter. The clearance between the coils being 1 mm when unloaded, the minimum compressive load to remove the clearance, is (A) 25 N (B) 30 N (C) 35 N (D) 40 N

Description : A spring of mean radius 40 mm contains 8 action coils of steel (N = 80000 N/mm2 ), 4 mm in  diameter. The clearance between the coils being 1 mm when unloaded, the minimum compressive  load to remove the clearance, is  (A) 25 N  (B) 30 N  (C) 35 N  (D) 40 N 

Last Answer : (C) 35 N 

A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is: (A) 4.0 mm (B) 4.5 mm (C) 5.0 mm (D) 5.5 mm

Description : A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that  stress in the wire does not exceed 100 N/mm2  is:  (A) 4.0 mm  (B) 4.5 mm  (C) 5.0 mm  (D) 5.5 mm

Last Answer : (C) 5.0 mm 

A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 MN/mm2 , the stresses developed are: (A) b = 10 N/mm2s = 20 N/mm2(B) b = 8 N/mm2s = 16 N/mm2(C) b = 6 N/mm2s = 12 N/mm2(D) b = 5 N/mm2s = 10 N/mm

Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that  of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2  MN/mm2  and Eb = 0.1 ... 6 N/mm2 s  = 12 N/mm2 (D) b = 5 N/mm2 s  = 10 N/mm

Last Answer : (A) b = 10 N/mm2 s  = 20 N/mm

Modulus elasticity of steel is generally taken as [ A ] 2 x 105 N/mm2 [ B ] 2 x 106 N/mm2 [ C ] 2 x 106 N/mm2 [ D ] 2 x 105 N/mm2

Description : Modulus elasticity of steel is generally taken as [ A ] 2 x 105 N/mm2 [ B ] 2 x 106 N/mm2 [ C ] 2 x 106 N/mm2 [ D ] 2 x 105 N/mm2

Last Answer : [ A ] 2 x 105 N/mm2

Modulus elasticity of steel is generally taken as [ A ] 2 x 105 N/mm2 [ B ] 2 x 106 N/mm2 [ C ] 2 x 106 N/mm2 [ D ] 2 x 105 N/mm2

Description : Modulus elasticity of steel is generally taken as [ A ] 2 x 105 N/mm2 [ B ] 2 x 106 N/mm2 [ C ] 2 x 106 N/mm2 [ D ] 2 x 105 N/mm2

Last Answer : [ A ] 2 x 105 N/mm2

Cast iron has (A) Very high tensile strength (B) High ductility (C) High malleability (D) Elastic limit close to ultimate breaking strength

Description : Cast iron has (A) Very high tensile strength (B) High ductility (C) High malleability (D) Elastic limit close to ultimate breaking strength

Last Answer : (D) Elastic limit close to ultimate breaking strength

Cast iron has (A) High ductility (B) High malleability (C) Very high tensile strength (D) Its elastic limit very close to ultimate breaking strength

Description : Cast iron has (A) High ductility (B) High malleability (C) Very high tensile strength (D) Its elastic limit very close to ultimate breaking strength

Last Answer : (D) Its elastic limit very close to ultimate breaking strength

Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Description : Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Last Answer : (B) Endurance limit

Cast iron is having very high (A) Proximity between its elastic limit and ultimate breaking strength (B) Ductility (C) Tensile strength (D) All (A), (B) and (C)

Description : Cast iron is having very high (A) Proximity between its elastic limit and ultimate breaking strength (B) Ductility (C) Tensile strength (D) All (A), (B) and (C)

Last Answer : (A) Proximity between its elastic limit and ultimate breaking strength

When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Last Answer : (c) 0.50

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Description : Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Last Answer : (D) Endurance limit

Distortion or change in shape of a cast partial denture clasp during its clinical use probably indicates that the: A. Ductility was too low B. Hardness was too great C. Ultimate tensile strength was too low D. Tension temperature was too high E. Elastic limit was exceeded

Description : Distortion or change in shape of a cast partial denture clasp during its clinical use probably indicates that the: A. Ductility was too low B. Hardness was too great C. Ultimate tensile strength was too low D. Tension temperature was too high E. Elastic limit was exceeded

Last Answer : E. Elastic limit was exceeded

What is the full form UTS of rails a. Ultimate technical Strength b. Ultimate tensile Strength* c. Upper Top surface d. None of above

Description : What is the full form UTS of rails a. Ultimate technical Strength b. Ultimate tensile Strength* c. Upper Top surface d. None of above

Last Answer : b. Ultimate tensile Strength*